Honeywell IS4813 - Manual

2 Introduction Product Overview The IS48xx series are miniature laser scan engines. The non-decode IS4813 and IS4815 laser scan engines are designed for direct integration into custom OEM devices equipped with a decoder. The engine’s small size is ideal for integration into mobile computers, hand-he...

3 Models and Accessories Non-Decode Engines Options Model Description IS4813 Non-Decode, 3.3VDC Scan Engine IS4815 Non-Decode, 5VDC Scan Engine Accessories Part Number Description 19-00358 Flex Cable, 10-POS, 67.5 mm Length Decode Engines Options Base Model Description IS4823 3.3VDC Scan Engine with...

4 Components of the IS4800 Engine Series IS4813 and IS4815 Non-Decode Engine Item Description Item Location 1 Pin Locator Holes (see page 6) Figure 3. IS4813/IS4815 2 Threaded Mounting Points (see page 6) 3 Exit Beam Location, Laser Light Aperture AVOID EXPOSURE! – LASER LIGHT IS EMITTED FROM THIS A...

6 Mounting Specifications IS4813 and IS4815 Scan Engine Dimensions The engine has two M1.6 tapped holes on the bottom of the chassis for mounting the engine with screws. Two additional blind holes are provided on the bottom of the engine for keying purposes to assist with engine alignment (see figur...

8 IS4823 and IS4825 (-0) Decode Printed Circuit Board Dimensions Warning: The limited warranty (on page 38) is void if the following recommendations are not adhered to when mounting the IS4800 series laser scan engine. When securing the decode board: • Use 3M™ 4032 1/32" double-coated urethane f...

9 Exit Beam Specifications Figure 9. IS4800 Series Exit Beam Specifications See page see pages 13 - 16 for information on window material specifications and enclosure design considerations. Specifications are subject to change without notice.

10 Return Aperture Specifications Figure 10. IS4800 Series Return Aperture Specifications See page see pages 13 - 16 for information on window material specifications and enclosure design considerations. Specifications are subject to change without notice.

11 Enclosure Specifications The IS4800 laser scan engine series was specifically designed for integration into custom housings for OEM applications. The scan engine’s performance will be adversely affected or permanently damaged when mounted in an unsuitable enclosure. Note: THIS DEVICE DOES NOT COM...

12 Flex Cables Note: To ensure optimum engine stability, use the flex cables shipped with the scan engine.  The host flex cable is used to carry power and data signals between the engine and the host system. The flex cable should allow for a minimal voltage drop and maintain a good ground connectio...

13 Exit Laser Beam Clearance • Keep the scan engine’s beam sweep free from obstructions. For detailed information on the exit beam angle and location, please refer to Exit Beam Specifications on page 9. • A dark matte-finish on the internal walls of the housing can be utilized to avoid internal beam...

14 Output Window Coatings • Anti-Reflection An anti-reflective coating can be applied to the inside and/or outside of the window to reduce the possibility of internal beam reflections interfering with the scan performance of the engine. If an anti-reflective coating is applied, it is recommended tha...

17 Scan Engine Field of View and Depth of Field Field of View  Distance from Engine Face Width of Field of View  50 mm (2") 57 mm (2.2") 254 mm (10") 264 mm (10.4")  9 See page for detailed information on the engine's exit beam specifications.  Figure 13. Typical Field of View ...

18 Timing Diagrams Startup Condition Timing Diagram The timing diagram below illustrates the correct power up procedure for the IS4813 and IS4815 engines. Scan Enable and Laser Enable are host driven signals. The Scan Enable and Laser Enable signals should be kept LOW (ON) at power up. Scan Control ...

19 Scan Sense Timing Diagram The Scan Sense signal is a 50% duty cycle square wave with the transitions from HIGH to LOW indicating a change in the scan direction of the scanning beam (see Figure 14). Valid scan data occurs between the HIGH to LOW transitions. Figure 15 illustrates the condition in ...

20 Descriptions of IS4823 and IS4825 Operating Modes Activation Modes The following activation modes initiate the engine’s laser and motor drive circuitry for bar code scanning. Activate Scanning with the External Trigger (Default). An external I/O pin is used to enable the scanning cycle. A High-to...

21 Transmit “NO READ” Message on Laser Timeout If the scanning cycle terminates without scanning a bar code during the cycle, a “NO READ” message is transmitted with the termination of the scanning cycle. Activate the LED Signal During the “NO READ” Transmission The LED signal is activated with the ...

22 Serial Configuration Mode The IS4823/IS4825 can be configured by scanning configuration bar codes † Figure 16 or by serial commands sent from the host device. With serial configuration, each command sent to the engine is the ASCII representation of each numeral in the configuration bar code (see ...

23 Example 2: The following sample illustrates the serial command sequence for configuring the engine for the factory default settings, disabling Code 128 scanning, and adding a “G” as a configurable prefix. Commands for features that require sequences of multiple bar codes for activation (i.e. pref...

24 General Design Specifications Operational Light Source: Visible Laser Diode (VLD) @ 650 nm Laser Power: 1 mW Depth of Scan Field: 50 mm – 254 mm (2" – 10") for 0.33 mm (13 mil) bar codes Width of Scan Field: 57 mm (2.2") @ 50 mm (2") from engine face 264 mm (10.4") @ 254 mm (1...

25 Electrical IS4813 IS4815 Input Voltage: 3.3VDC ± 0.3VDC 5.0VDC ± 5% Power Consumption: 400 mW 350 mW Typical Operating Current: < 120 mA @ 3.3VDC < 70 mA @ 5.0VDC Peak Operating Current*: < 300 mA @ 3.3VDC < 200 mA @ 5.0VDC Standby Current: < 30 mA @ 3.3VDC < 15 mA @ 5.0VDC IS48...

26 Detailed Electrical Specifications Absolute Maximum Ratings Signal Signal Description Minimum Maximum Vinput Voltage Applied to Any input pin (except D+ and D-) * † -0.3V Vin Voutput Voltage Applied to Any output pin ** -0.3V Vin + 0.3V * For USB version, Voltages on D+ and D- signal must conform...

28 Scan Engine Terminations IS4813 Engine Connections 10-Pin ZIF Connector Figure 17. IS4813 Pin Signal Name Function 1 No Connect No Connect 2 Power, V 3.3V ± 0.3V CC 3 No Connect No Connect 4 Laser Enable* High = Laser OFF Low = Laser ON, only if pin 5 (scan enable) is also Low 5 Scan Enable* High...

29 Decode Printed Circuit Board Terminations USB Decode PCB, 3.3V Figure 19. 12-Pin ZIF Connector Pin Signal Name Function 1 No Connect No Connection 2 +3.3V Power: Supply Voltage Input, +3.3V ± 0.3V 3 GND Ground: Power and Signal Ground 4 D- Input: USB D- Signal 5 <reserved> Pin Function Rese...

32 Flex Cable Specifications and Installation Guidelines Figure 22. Flex Cable Specifications and Installation Guidelines Specifications are subject to change without notice.

33 Bar Code Element Time Calculation Realization of the full depth of field for all bar codes given in the specification is based on the ability of the decoding hardware to resolve a varying range of minimum element times. The minimum element time calculation for a given bar code size at a given dis...

34 Regulatory Compliance Note: THIS DEVICE DOES NOT COMPLY WITH 21 CFR 1040. USE ONLY AS A COMPONENT. The IS4800 Series Laser Scan engines are designed to meet the requirements of IEC Class 2 in accordance with IEC 60825-1:2007. IEC Class 2 is defined as follows: Emission Duration: Greater than 0.25...

35 United States Laser Safety To assist with the FDA filing requirements (refer to Regulatory Requirements), Honeywell has registered the scan engine with the FDA as a component. Customers can contact CDRH at the following address: U.S. Food and Drug Administration Center for Devices and Radiologica...

36 Canada Laser Safety The Radiation Protection Bureau currently accepts products meeting the FDA standards in Canada. For more information contact: Radiation Protection Bureau 775 Brookfield Road Ottawa, Ontario K1A 1C1 EMC Products meeting FCC 47 CFR Part 15 will meet Industry Canada interference-...

38 Limited Warranty Honeywell International Inc. ("HII") warrants its products and optional accessories to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not c...

39 Index A Accessories ........................................................... 3 Activate ................................................. See Modes Aperture clearance .......................................................... 13 ASCII ..............................................................

41 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please contact us by using one of the methods below: Knowledge Base: