Honeywell GC-715N24 - Manual

Page 2 - MEMO; CAUTION; Explanation of Graphical Symbols.; dangerous voltage

MEMO RISK O F ELECTRIC SHO C K DO N O T O PEN CAUTION CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER(OR BACK). NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PRERSONNEL Explanation of Graphical Symbols. This symbol is intended to alert the user to the pres...

Page 3 - CAUTIONS FOR SAFE OPERATION !; Accessory

CAUTIONS FOR SAFE OPERATION ! ● Changes or modifications not approved by manufacturer could void the user’s authority to operate the equipment. ● To prevent fire or shock hazard, do not expose this camera to rain or moisture. ● To prevent electric shocks and other hazards, do not use different from ...

Page 4 - Name and function of each section; Outlines

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ 68 51 ① AUTO IRIS lens connector ② AUTO IRIS lens select switch ③ Sync. select switch ④ Video output connector ⑤ Power input connector ⑥ Power lamp ⑦ DC IRIS level adjustment (when using DC IRIS lens) ⑧ V- PHASE adjustment (when using LINE LOCK) Name and function of each section [uni...

Page 5 - Installation; Mounting a Lens; adjust carefully. It may cause any hunting.; Connection of AC power supply; Recommended power source capacity :

Installation Mounting a Lens 1. Remove the protective cap in front of the camera.2. Confirm the mount ring whether it is for C or CS. * Caution13. Attach the lens to the lens mount ring.4. If the lens has an Auto Iris mechanism, connect the iris cable to the Lens connector (EE/VSD S/W must be set to...

Page 6 - Adjustment and operations; Configuration

Adjustment and operations Fig 1. SIDE view Fig 2. REAR view Configuration The function of each part 1. Button “1” & “2” In line lock mode, zero crossing point can be adjusted by pressing these buttons.In MWB mode, manual white balance can be adjusted by pressing these buttons. 2. Button “3” In O...

Page 7 - ME

3. Connector “4” Used for EEPROM data setting in factory. 4. DIP switch “5” Shipment setting consists of “AGC High”, “AWC”, “SENS”. Fig 3. Button detail ① “EE/ME” Mode ( Electronic Exposure / Manual Exposure ) If using electronic exposure or a lens with automatic iris, the “EE/ME” switch has to be s...

Page 8 - in case of using DC iris lens.; Auto

◆ in case of using AUTO iris lens -. Set “EE/VSD” switch on Side to “VSD”. -. Set “EE/VSD” switch on Rear to “VSD”. ② “EE/VSD” Mode ( Lens type selection ) If using a manual lens, the “EE/VSD” switch has to be set to “EE”. If using a lens with automatic iris, the “EE/VSD” switch has to be setto “VSD...

Page 9 - BMB

⑤ “BMB/SENS” Mode What is BMB?-. BMB is the trade mark of Honeywell, that means BLACK MASK BLC. ( BMB BMB TM ) -. It is to improve the weak points of Electronic Iris & BLC.-. Mask the excessive light by 3 making level and minimize the loss of outlines of Objects due to strong light. ④ “AGC” Mode...

Page 11 - ! Cautions in SENS mode; FL

! Cautions in SENS mode 1. In high sensitivity mode , moving object is displayed as if it is flowing, because the integration time of the CCD becomes long.Further, movement is unnatural due to intermittent read-out. 2. In high sensitivity mode, white blemishes may be remarkable. 3. In high sensitivi...

Page 14 - SPECIFICATIONS

SPECIFICATIONS 23 23 GC-715N24 GC-715P24 Imaging device 1/3” CCD(total 410,000pixels) 1/3” CCD (total 470,000pixels) Effective pixel 768H * 494V(380,000pixels) 752H * 582V(440,000pixels) Scanning system 525 Lines 2:1 Interlace 625 Lines 2:1 Interlace Sync system Internal/ Line lock Internal/ Line lo...

Honeywell GC-715N24 - Manual

Table of Contents:

Summary

Other Honeywell Models