Honeywell CT1800- User Manual
Honeywell CT1800– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Thermostat
- Page 3 – MOUNT WALLPLATE OR SUBBASE
- Page 4 – WIRE WALLPLATE OR SUBBASE; NOTE: All wiring must comply with local electrical codes; from affecting thermostat operation.
- Page 5 – SINGLE STAGE HEAT PUMP; Subbase Terminal
- Page 6 – MOUNT THE THERMOSTAT; wallplate or subbase.; SET HEAT ANTICIPATOR LEVER; OIL BURNER CONTROL; as shown above, or as recorded in Step 7.
- Page 7 – CAUTION
- Page 8 – Helping You Control Your World; Heating/Cooling System
1
69-0394—3
D.F. • Rev. 11-96 • Printed in U.S.A. • • ©Honeywell Inc. 1996 • Form Number 69-0394—3
Installation Instructions
CT1800 24V gas or oil heat, or 3 wire zone valves.
CT1801 24V gas or oil heat/cool.
CT1802 24V central electric heat/cool or single stage
heat pump without auxiliary heat.
Not for use on line voltage (120V) millivolt systems
.
CT1800, CT1801, CT1802
Electromechanical Fuel Saver Thermostat and Wallplate/Subbase
Recycling Notice
This control contains mercury in a sealed tube. Do
not
place control in the trash at the end of its useful life.
If this control is replacing a control that contains mercury in
a sealed tube, do
not place your old control in the trash.
M3375
THERMOSTAT FEATURES
M3375
I—Front of thermostat.
M9613
HIGH TEMPERATURE
CONTROL LEVER
(RED)
LOW TEMPERATURE
CONTROL LEVER (BLUE)
THERMOSTAT COVER
THERMOMETER
THERMOSTAT
BASE
24 HOUR PROGRAM DIAL
(GRAY AREA FOR
NIGHT SETTINGS)
AAA ALKALINE
BATTERY (2) INCLUDED
LOW TEMPERATURE
CONTROL LEVER
(BLUE)
HIGH
TEMPERATURE
CONTROL LEVER
(RED)
SWITCH
BULBS
CAPTIVE
MOUNTING
SCREW
CAPTIVE
MOUNTING
SCREW
WALLPLATE (BEHIND
THERMOSTAT. HELD
ON BY TWO CAPTIVE
SCREWS.)
ADJUSTABLE HEAT
ANTICIPATOR
PROGRAM
INDEX WHEEL
TIME INDICATOR
ARROW
HEAT
ANTICIPATOR
SETTING
LEVER
M9615
III—Cover removed.
II—Hinged cover lifted.
24 HOUR PROGRAM DIAL
(GRAY AREA FOR NIGHT
SETTING)
TIME
INDICATOR
ARROW
PROGRAM
PIN
STORAGE
THERMOSTAT COVER
PROGRAM
INDEX WHEEL
PROGRAM
PIN SLOT
PROGRAM PINS
FLIP-UP
COVER
M9614
Contact your local waste management authority for
instructions regarding recycling and the proper disposal of
this control, or of an old control containing mercury in a
sealed tube.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell CT1800
Summary
69-0394—3 2 TABLE 1—THERMOSTAT AND SUBBASE APPLICATIONS. a 1 PREPARATION Check thermostat and wallplate suitability for your heating or heating/cooling system. Refer to Table 1. Assemble tools as required. FLAT BLADESCREWDRIVER HAND OR POWERDRILL WITH 3/16 INCHDRILL BIT, IF NEEDED TODRILL HOLES IN W...
3 69-0394—3 M6115 BULBSWITCH ANTICIPATORSCALE ANTICIPATORSETTING LEVER Disconnect wires from old thermostat, wallplate orsubbase. Tape each end and label with the letter of the terminal designation to make reconnection easier. Ifthere are only two wires labeling is not necessary. IMPORTANT: If old t...
69-0394—3 4 3 SCREW HOLES WITH PLASTICANCHORS HEATING-ONLYWALLPLATE M9612 AUTO OFF COOL HEAT ON FAN B O W Y R G M2419 SPIRIT LEVEL 5 WIRE WALLPLATE OR SUBBASE NOTE: All wiring must comply with local electrical codes and ordinances. Refer to illustration and strip thermostat wireinsulations as necess...
