Honeywell 9PGTPA 100 - User Manual
Honeywell 9PGTPA 100 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – MAINTENANCE MANUAL; CAS-100 COLLISION AVOIDANCE SYSTEM; Installation Planning; B. Location of Equipment; wiring
- Page 3 – C. Interwiring and Cable Fabrication
- Page 9 – TPA-100A TCAS Processor Aft Connector
- Page 11 – Pin
- Page 24 – Chassis Ground
- Page 25 – Strap Common
- Page 26 – ITA-81A Aft Connector
- Page 27 – D. Wire Strapping Options; (b) Aircraft Altitude Limit Program Straps
- Page 30 – Equipment Installation; lead length; B. TCAS Directional Antenna Installation; (1) Directional Antenna Positioning and Wiring Specifications
- Page 34 – Adapter and Moldable Shim Assembled on the Airframe
- Page 35 – C. TCAS Omni Antenna Installation; (1) Antenna Positioning and Wiring Specifications; E. Dedicated TCAS Traffic Display
- Page 36 – Equipment
- Page 40 – CAUTION: INSTRUMENT FLIGHT RULES TCAS RAMP TEST EQUIPMENT; • Pitot-Static Test Set
- Page 47 – Table 2005. Upper TCAS Antenna Bearing Accuracy Chart; Ground Reference; Degrees
- Page 48 – Table 2006. Lower TCAS Antenna Bearing Accuracy Chart; Remove the Flight Data Recorder Test set from the FDR.
- Page 52 – Input Discetes and Program Pin Information
- Page 53 – Table 2007. Input Discretes and Program Pin Information; Airworthiness and Operational Approval of TCAS System
- Page 54 – Removal and Replacement; are aligned and the connector is fully engaged.; B. Directional Antenna; sealant to assembly screws.
- Page 55 – D. Dedicated TCAS Traffic Display; connector from aft of unit.; E. TRA-67 ATC Mode S Transponder System Component
- Page 56 – Maintenance Procedures; performing
- Page 57 – Aircraft Maintenance Programs; Air; B. Honeywell TCAS Maintenance Recommendations
- Page 59 – TPA-100A TCAS Processor Outline Drawing
- Page 71 – ITA-81A Traffic Display Outline Drawing
- Page 73 – CAS-100 Interwiring Diagram
- Page 86 – TABLE A. RADIO ALTIMETER STRAPS; Electrical Characteristics
- Page 87 – TABLE B. ANTENNA DELAY PROGRAM STRAPS; EITHER PRIMARY OR FAN POWER.; Differential
- Page 88 – PIN; Primary Alt. Rate Input
- Page 107 – Table 2017. IVA-81B Configuration Matrix
Page 2001
1 Dec 2003
34-45-4
7
MAINTENANCE MANUAL
CAS-100 COLLISION AVOIDANCE SYSTEM
Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.
MAINTENANCE PRACTICES
1. General
The function of this section is to supply the service personnel with installation and maintenance
data for the Honeywell CAS-100.
Components that are necessary in a CAS-100 installation that are part of other systems are
included in this manual only as necessary to know their function in a TCAS system. Components
that are part of the CAS-81 system are included in the related component maintenance manuals
recorded in Table 5 of this manual.
Installation and maintenance data for the Mode S transponder, control units, and transponder
related omni antennas are given in the applicable Mode S transponder system maintenance
manual. (Refer to Table 5 in the DESCRIPTION AND OPERATION section of this manual.)
The installation instructions are supported by mechanical outline drawings and electrical
interconnection drawings. These drawings, found at the back of this section, must be reviewed
by the installing agency and specifications peculiar to the applicable airframe established before
the installation is started.
2. Unpacking
Be careful when remove the contents of the CAS-100 components. Open send containers and
carefully remove all items. Check the contents to make sure that all items identified on the packing
list are included. Visually examine each component for damage caused during shipment; that is
examine for dents, depth of abrasions, damaged paint, etc. If some component is damaged, tell
the transportation carrier immediately.
3. Preinstallation Testing
The components of the CAS-100 system have all been adjusted and tested before shipment.
Thus, preinstallation testing is not necessary. If preinstallation bench testing of the units is
necessary, reference must be made to Section 1000, TESTING AND TROUBLESHOOTING, of
the component maintenance manual for the applicable unit. Refer to Table Intro-1 in the
INTRODUCTION section of this manual for a list of component maintenance manuals.
4. Equipment Changes and Markings
Honeywell uses a standardized marking system to give a procedure for identifying equipment that
has changes included. Refer to the front of the applicable unit Component Maintenance Manual
for a list of Service Bulletins affecting the different units in the CAS-100 system.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2002 1 Dec 2003 34-45-4 7 MAINTENANCE MANUAL CAS-100 COLLISION AVOIDANCE SYSTEM Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document. 5. Installation Planning A. General The following paragraphs contain data for the initial inst...
Page 2003 1 Dec 2003 34-45-4 7 MAINTENANCE MANUAL CAS-100 COLLISION AVOIDANCE SYSTEM Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document. The bottom TCAS antenna (directional or omni) must be put within 5 degrees of the center line ...
Page 2009 1 Dec 2003 34-45-4 7 MAINTENANCE MANUAL CAS-100 COLLISION AVOIDANCE SYSTEM Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document. (b) Directional Antenna Connectors Four coaxial cables that use TNC connectors connect the dir...
