Honeywell 8712309L - User Manual

A

ENGLISH

Electronic Deadbolt with Keypad

1 2 3
4 5 6 0
7 8 9

G

H

I

J

K

M

M

H

L

B

C

D

E

F

1 - Exterior Faceplate
1 - Interior Faceplate
1 - User Guide
2 - Keys

1 - Strike Plate
1 - Mounting Plate
1 - Latch
1 - 1 3/8” Screws

2 - Mounting Post

2 - 5/16” Screws
2 - 1” Screws
4 - 3/4” Screws

Read this manual carefully before installing and operating!

Please carefully check the above list to confirm all items have been received. If any items are
missing, please contact Consumer Assistance. (See page for contact information)

3/4” Screws

1” Screws

5/16” Screws

1 3/8” Screws

Optional Set Screw

Mounting Post

Package Includes:

A

Exterior Faceplate

User Guide

Keys

Latch

Strike plate

Interior Faceplate

Mounting Plate

1

Installation Overview

Install Interior Assembly

5

NOTE: Make sure the Turn Knob is in the correct position.
Be careful not to pinch the control wire when assembling

I

H

C

B

3 Install Exterior Assembly

Refer to Template included

for Door Prep Instructions

Example

Preparing Door

• Drill

• 2 1/8” Hole Saw

• 1” Hole Saw

• 3/4” Chisel

Tools Needed for Door Preparation

(if there is no knob hole):

NOTE: Skip this step if your door comes with pre-drilled holes.

2 1/8” Hole Saw

K

E

F

Strike Plate Installation

NOTE: The strike plate on the door frame

needs to be straight and not protruding from

door frame. Make adjustment before installing

or this will cause problems with bolt

fitting into latch hole.

1” Hole Saw

1.

2.

3.

4.

2

J

M

C

C

Install Enclosed Latch and Strike Plate.

Do not over-tighten latch screws.

Deadbolt Latch Must Be

Retracted During Installation.

Screw Mounting Post (M)

into holes on Mounting Plate (C).

Remove (J) Screw from inside

the battery compartment within the

(B) Housing to release the Mounting

Plate (C).

Preparation for Interior Assembly.

The latch plate on the door needs to be straight and not protruding

from door. Make adjustment before installing or this will cause

problems with bolt fitting into latch hole.

NOTE: Do not extend Cylindrical Cover past 2-3/4” (70mm).

TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET:

1. Hold latch with numbers facing forward and thumb pressing on the bolt.

2. Rotate the cylinder cover clockwise.

3. Pull and twist the extension plate all the way out.

4. Rotate the cylinder counter clockwise so that the marking aligns with

the 2-3/4” position indicator.

2-3/4” position

E

2-3/8” position

E

K

Read this manual carefully before

installing and operating!

Important

Use the QR code below for the most up to date instructions:

Turn Knob

Testing Operation

7

Test unlocking

Press 1-2-3-4-

• #2 Phillips Screwdriver

Do Not use an electronic screwdriver

Tools Needed for Lock Installation:

L (optional)

H

C

VERTICAL

POSITION

(L) screw goes into the door to

prevent the lock from shifting and

is optional.

Work with the door open

Check that the Rubber Gasket is secured on the Exterior Assembly. Insert the

Exterior Assembly onto the door with the tailpiece going through the Deadbolt

Latch in the

VERTICAL POSITION

.

Secure mounting

plate to the door

Route the Control Wire through the door UNDER the Deadbolt Latch.

Please check your door to see if it’s aligned properly and then adjust the strike plate.

If not, go back to step 2 and ensure you followed the steps.

C

B

Carefully insert control wire

into the wire connector

Work with the door open

4 Install Interior Assembly

NOTE:

Make sure the connector dots line up with the dots on the control wire

Do not Turn Knob until batteries have been installed and

lock has handed. This automatically determines if your

door opens to the left or right.

Do not use rechargeable

batteries or non-alkaline

batteries. Do not use a mix

of old and new batteries.

Install Batteries and Cover

6

B

This Electronic lock requires (4) High Quality AA Alkaline
batteries. When all 4 batteries are installed in the correct
position the lock will automatically lock which determins the
handing of the door.

When completed the lock will beep and the touchscreen will
flash red and green and the numbers will light up.

NOTE: Do not touch the Keypad until the light turns off.

Before Opening Door

Let Motor Complete Cycle

Test the lock button with door open