Honeywell 8650 - Installation Manual
Honeywell 8650 – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – the unit when they are installing the wall plate.
- Page 4 – Retrofit Mounting Installation; The following illustration is for
- Page 5 – Retrofit Mounting Options
- Page 6 – WIRING; Follow the wiring details explained in this section.; FHD500 Monitor Wall Plate; in electrical shock and/or equipment damage.
- Page 7 – Terminal Strip Wiring
- Page 8 – Use the following diagram to properly wire the FHD500:; TY
- Page 9 – TROUBLESHOOTING; Screen is black
F
UME
H
OOD
D
ISPLAY
500 S
ERIES
(FHD500)
75 Discovery Way • Acton, MA 01720 •
Tel (978) 795-1285 • Fax (978) 795-1111
•
www.phoenixcontrols.com
©2024 Phoenix Controls. Specifications subject to change without notice. Rev.A 04/2024 651-000-014 ECN-00046798
FHD500 I
NSTALLATION
G
UIDE
I
NSTALLATION
G
UIDE
GENERAL INSTALLATION INSTRUCTIONS
This document covers mounting and wiring for the Phoenix Controls Fume Hood Display 500 Series (FHD500). This document
assumes that you are an engineer, technician, or service person trained to perform control system installations.
Before You Begin
Unpack and inspect the package contents for damaged or missing components. If contents are damaged, notify the appropriate
carrier at once and return any damaged components for immediate repair or replacement. Included in the package are the following:
•
Fume Hood Display 500 Series (FHD500)
•
Hardware bag containing two (2) Phillips Pan Head Screw #8 x 3/4 and wiring pin installation tool
Required Tools and Materials
•
Fume Hood Display 500 Series (FHD500)
•
Two (2) Phillips Pan Head Screw #8 x 3/4
•
Depending on what you order, there could also be a Hub and retro/recess mount bracket with additional hardware.
•
Suitable tools and fasteners for mounting the device and accessories:
•
Two (2) Phillips screwdriver used to install and remove an existing Fume Hood Monitor
•
Small flat-blade screwdriver used for making wiring connections
•
Included wiring pin installation tool
Electrical Box/Mounting
The FHD500 and its components are designed to be installed within standard size electrical gang boxes.
The FHD500 monitor requires standard 3-1/4 in (82.75 mm) mounting hole spacing or standard European 2-3/8 in (60.3 mm)
mounting hole spacing.
If utilizing an electrical box, suitable US model electrical boxes are Raco 8670, Raco 8650, Raco 8663, or equivalent.
FHD500 Base Plate and Display
Using the supplied screws, mount the base plate to the single gang electrical box using either the US 3-1/4 in (82.75 mm) hole
spacing or the European 2-3/8 in (60.3 mm) hole spacing. Pull the wires through the hole in the base plate and leave enough slack
to install the wires in the terminals. Install the wires using the instructions in the wiring section.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell 8650
Summary
2 FHD500 I NSTALLATION G UIDE 651-000-014 ECN-00046798 ©2024 Phoenix Controls. Specifications subject to change without notice. Rev.A MOUNTING THE FHD500 The FHD500 screen is mounted to the base plate from the bottom up and at a slight angle, making sure that all interior connections are properly al...
4 FHD500 I NSTALLATION G UIDE 651-000-014 ECN-00046798 ©2024 Phoenix Controls. Specifications subject to change without notice. Rev.A Retrofit Mounting Installation For retrofit mounting of the FHD500, use the following guidance: • Mount the FHD500 and bracket assembly to the fume hood:1. Slide the ...
©2024 Phoenix Controls. Specifications subject to change without notice. Rev.A 04/2024 651-000-014 ECN-00046798 FHD500 I NSTALLATION G UIDE 5 Retrofit Mounting Options • RD1: Retrofit stainless surface plate to cover FHD1xx recess mounting holes • RM1: Retrofit stainless surface plate to cover FHMx0...
