Honeywell 800-08115 - Manual
Honeywell 800-08115 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 2. Installing the GSMVLP5 in the LYNX Touch; unit with the blade of a medium size screwdriver (Refer to Figure 3).; For Documentation and Online Support:
- Page 3 – Figure 3. Installing the ILP5 in the LYNX Touch
- Page 4 – Electrical Specifications; GSMVLP5
800-08115 1/11 Rev. B
GSMVLP5 GSM and
ILP5 Ethernet
Communications Modules
Installation and Setup Guide
Installing Communication Modules
!
RF Exposure
WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna(s) or transmitter.
Installing the GSMVLP5 in the LYNX Touch Series Control
Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the
module in the LYNX Touch.
1. Install the provided FCC/IC label (P/N 800-08334) on the control’s case back (refer to Figure 1).
5000-100-186-V0
FCC ID: CFS-8DLL
YNXTOUCH1
IC: 573F-L
YNXTOUCH1
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY
CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS
DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
800-08126 1/11 Rev A
LYNX TOUCH SERIES
COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: AC3AL05BL5000
RINGER EQUIVALENCE: 0.1B
IC MODEL: L
YNXTOUCH1
CONTAINS TRANSMITTER MODULE
IC: 7830A-MC55I
FCC ID: QIPMC55I
800-08334 2/11 Rev A
FCC ID: CFS-8DLLYNXTOUCH1
IC: 573F-LYNXTOUCH1
LYNX TOUCH SERIES
IC MODEL: LYNXTOUCHG1
Figure 1. FCC/IC Label Location
2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the
unit with the blade of a medium size screwdriver (Refer to Figure 2).
3. Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly
seated into the receptacle on the control (Refer to Figure 2).
4. Secure the GSMVLP5 with the three provided screws (Refer to Figure 2).
5. Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device.
Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and
Setup Guide (P/N 800-06834 or higher).
For Documentation and Online Support:
http://www.security.honeywell.com/hsc/resources/MyWebTech
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
SCREW (3) SIM CARD 5000-100-151-V1 ROTATED 180 CONNECTOR BOARD CONNECTOR BOARD RECEPTACLE GSMVLP5 LYNX TOUCH LOCKING TABS Figure 2. Installing the GSMVLP5 in the LYNX Touch Installing the ILP5 in the LYNX Touch Series Control Ensure that the connector board and cable are securely installed in the IL...
5000-100-154-V1 SCREW (3) ROTATED 180 CONNECTOR BOARD RJ45 RECEPTACLE CONNECTOR BOARD RECEPTACLE ILP5 LYNX TOUCH TIE WRAPPOINT REMOVE ILP5 SPACER ILP5 SPACER REMOVE ILP5 KNOCKOUT TIE WRAP (1) RJ45 RECEPTACLE LYNX TOUCH ALTERNATE INSTALLATION LOCKING TABS ETHERNET CABLE TO ILP5 Figure 3. Installing t...
Electrical Specifications GSMVLP5 Voltage Input 5V Current Idle 15 mA, standby Average 300mA, average transmit Peak 1.6A peak transmit, 25% duty cycle ILP5 Voltage Input 5V Current: 83 mA, 100 Base T with traffic 41 mA, 10 Base T with traffic 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melvil...
