Hobart FP400 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS

– 2 – TABLE OF CONTENTS MODEL FP400 FOOD PROCESSOR ............................................................................................. 3 GENERAL .......................................................................................................................................... 4 INST...

Page 3 - MODEL FP400 FOOD PROCESSOR

– 3 – © HOBART CORPORATION, 1998 MODEL FP400 FOOD PROCESSOR (Shown with Feed Hopper Attachment)

Page 4 - UNPACKING

– 4 – Installation, Operation and Care of HOBART MODEL FP400 FOOD PROCESSOR PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL The FP400 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicingvegetables, fruits, or cheese. A wall rack, and a wide range of slicer, shredder, an...

Page 5 - VERIFY CORRECT ROTATION

– 5 – VERIFY CORRECT ROTATION Verify correct rotation of the knife shaft. Make sure it moves in a clockwise direction looking down intothe feed cylinder. If the rotation is incorrect, UNPLUG THE ELECTRICAL CORD and interchange anytwo of the three power supply leads (non grounding wires) inside the p...

Page 6 - OPERATION

– 6 – OPERATION WARNING: ROTATING KNIVES INSIDE. ALWAYS USE THE FEED HOPPER OR PUSHER PLATEFEED ATTACHMENT. KEEP HANDS OUT. Proper assembly of the FP400, including selection of the appropriate cutters, is necessary for correctoperation of the food processor. Refer to the CUTTING TOOL GUIDE for sizes...

Page 7 - INSTALLING THE CUTTING TOOLS; Always push the red STOP button before changing cutters.; Dicing and French Fries; the dicing grid clockwise as far as it will go.

– 7 – INSTALLING THE CUTTING TOOLS Always push the red STOP button before changing cutters. Slicing, Shredding, Grating, and Julienne Cutting 1. Pull the locking handle forward and swing the feed cylinder out to the rear. 2. Place the ejector plate (Fig. 4) on the knife shaft. Press the ejector plat...

Page 8 - The feed cylinder cannot be closed.; REMOVING THE CUTTING TOOLS; Removing the Feed Attachments in this manual).

– 8 – 4. Screw the decoring screw (if using the pusher plate feed attachment) (left-hand thread) OR the agitator device (if using the feed hopper attachment) (left-hand thread) into position in the cuttingtool center. 5. Release the catch, swing the feed cylinder back into position, and raise the lo...

Page 10 - clockwise and remove it.

– 10 – Pusher Plate (Use the decoring screw to secure the plates to the knife shaft.) 1. Press the STOP button. 2. Fit the feed cylinder with three internal knives (see Fig. 8). 3. Move the pusher plate handle (Fig. 10) all the way up. 4. Insert the pusher plate attachment shaft (Fig. 10) into the f...

Page 13 - CLEANING; Do not leave the cutting blades in a wet condition when not in use.

– 13 – CLEANING WARNING: TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING. Clean the machine immediately after each use. Dismantle all removable parts from the machine andwash them in warm water and a mild detergent. Rinse thoroughly and wipe dry with a soft clean cloth.Wipe the e...

Page 14 - MAINTENANCE; REPLACEMENT DICING GRIDS

– 14 – 2. Remove the feed cylinder. The feed cylinder guides (see Fig. 7) OR the three knives (see Fig. 8) may be removed for cleaning by unscrewing the nuts (see Fig's. 7 & 8) with the wrench provided.Rinse all parts with lukewarm water. 3. Remove the cutting tool. 4. If you have used a dicing ...

Page 15 - TROUBLESHOOTING; SYMPTOM; Low output or poor cutting results.; POSSIBLE CAUSE; Broken wire or connection.; SUGGESTED ACTION

– 15 – TROUBLESHOOTING SYMPTOM Machine will not start or stopswhile operating and won't restart. Low output or poor cutting results. POSSIBLE CAUSE 1. M a c h i n e p l u g n o t i n s t a l l e dsecurely into receptacle. 2. Feed cylinder not locked incorrect position. 3. Feed hopper locking knob no...

Page 16 - Cutting tool locked to shaft.

– 16 – SYMPTOM Cutting tool locked to shaft. Decoring screw or agitator devicecannot be removed. POSSIBLE CAUSE Build-up between cutting tool anddicing grid or potato chip grid. Devices have tightened during useof the machine. SUGGESTED ACTION Always use the ejector plate. Usea thick leather glove a...

Hobart FP400 - Manual

Table of Contents:

Summary

Other Hobart Models