Hobart LT1 ML-104239 - Manual

Page 2 - TABLE OF CONTENTS

– 2 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 UNPACKING . . ....

Page 3 - The Model LT1 Dishwasher is a low temperature (140; MODEL LT1 DISHWASHER

– 3 – Installation, Operation and Care of Model LT1 DISHWASHER SAVE THESE INSTRUCTIONS GENERAL The Model LT1 Dishwasher is a low temperature (140 ° F recommended, 120 ° F minimum), chemical sanitizing, rack-type dishwasher for use with accessory 20" x 20" racks. It is equipped with a 3 ⁄ 4 h...

Page 4 - INSTALLATION; UNPACKING; Remove the two screws and nuts that secure

– 4 – PL-40920-1 FRONT RACK TRACKAND SPLASH GUARD SCREWS INSTALLATION UNPACKING Immediately after unpacking the dishwasher, check it for possible shipping damage. If this machineis found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installat...

Page 6 - Turn drain pan and drain pan strainer 180; Water Supply Connection; The recommended water supply temperature is 140

– 6 – DISH TABLES Dish table end should be turned down and fitted over the lipof the dishwasher tank (Fig. 4). Use an NSF approved sealerbetween table and tank lip to prevent leaks. Fasten tables tothe tank lip; truss head screws (by others) are recommended. PLUMBING CONNECTIONS Fig. 4 WARNING: PLUM...

Page 7 - ELECTRICAL CONNECTION; ELECTRICAL DATA; Connect the incoming power supply through the hole for; CHEMICAL SUPPLIES; FILL

– 7 – ELECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THEAPPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCALELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING O...

Page 8 - CYCLE TIMER ADJUSTMENT; by the door cycle switch.

– 8 – CYCLE TIMER ADJUSTMENT The cycle timer, which regulates the dishwasher cycle, may require adjustment in order to suit localconditions. To gain access to the cycle timer, loosen the bottom screw on the access cover locatedon the right side of the control box and rotate the access cover up (Fig....

Page 9 - OPERATION

– 9 – OPERATION CAUTION: Items made of pewter, aluminum, and silver will be attacked by the sodiumhypochlorite sanitizing agent (liquid bleach) used in this machine and therefore should not bewashed in it. In addition to these detailed instructions, brief instructions for operation and cleaning can ...

Page 10 - MACHINE PREPARATION; To initially fill the machine, press the

– 10 – MACHINE PREPARATION Check to make sure that the pump intake strainer (Fig. 12), the drain pan strainer (Fig. 13), and thedrain tube (Fig. 17) are in place and that both strainers are free of debris. The pump intake strainermust drop completely to the bottom of the sump. THE DRAIN AND STRAINER...

Page 12 - CLEANING THE DISHWASHER; Thoroughly cleanse and flush the dishwasher; switch On, close the doors, and press and hold the; Cleaning the Wash Arms; Replace the end caps.

– 12 – CLEANING THE DISHWASHER C l e a n t h e d i s h w a s h e r a f t e r e a c h w o r k i n gshift. Never use steel wool to clean warewashersurfaces. Use only products formulated to besafe on stainless steel. 1. Drain machine. Turn the P OWER switch Off. 2. Thoroughly cleanse and flush the dish...

Page 14 - MAINTENANCE; DELIMING

– 14 – MAINTENANCE DELIMING WARNING: DELIMING SOLUTION MUST NOT COME IN CONTACT WITH BLEACH OR RINSESOLUTION CONTAINING BLEACH USED IN THIS MACHINE. MIXING MAY CAUSE HAZARDOUSGAS TO FORM. THIS ENTIRE PROCEDURE MUST BE FOLLOWED STEP-BY-STEP FOR SAFEAND SATISFACTORY RESULTS. The dishwasher should be d...

Page 15 - LUBRICATION

– 15 – 13. Run machine without loading dishware for two complete cycles to remove the chemical deliming agent. 14. Reconnect sanitizer, detergent, and rinse aid systems. 15. With the standpipes installed in their respective containers (red in detergent, white in sanitizer, blue in rinse aid), press ...

Page 16 - TROUBLESHOOTING; SYMPTOMS

– 16 – TROUBLESHOOTING Symptoms that persist after possible causes have been checked may require service. SYMPTOMS POSSIBLE CAUSES No Machine Operation 1. Machine POWER switch in the OFF position. 2. Blown fuse or tripped circuit breaker at power supply.3. DELIME/NORMAL switch in the DELIME position...

Hobart LT1 ML-104239 - Manual

Table of Contents:

Summary

Other Hobart Models