Heat & Glo 6000 ARCH - Manual

Heat & Glo 6000 ARCH

Heat & Glo 6000 ARCH – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
Page: / 46

Table of Contents:

  • Page 2 – SAFETY AND WARNING INFORMATION
  • Page 3 – ii; Section 5: Replacement Parts
  • Page 4 – Appliance Certification; CERTIFICATION; Installation Codes
  • Page 9 – Clearance Requirements
  • Page 10 – CAUTION; NOTE: DIMENSIONS SHOWN IN INCHES
  • Page 11 – A. Vent System Approvals; Installers Guide. The drawing; Figure 6. Vent Components and Terminations
  • Page 12 – Figure 7. D-Series Direct Vent Component Specifications
  • Page 14 – Figure 9. Vertical Venting; VERTICAL VENTING
  • Page 16 – Figure 11. Venting with two 90° elbows
  • Page 17 – Figure 12. Venting with two 90° elbows
  • Page 18 – Figure 13. Venting with three 90° elbows
  • Page 19 – Figure 14. Venting with three 90° elbows
  • Page 20 – B. Installing Vent Components; Attach the First Vent Component to the
  • Page 21 – Continue Adding Vent Components; • Ensure that each succeeding vent component is
  • Page 22 – To install support brackets for horizontal runs:
  • Page 23 – Figure 18. Installing Support Brackets; NOTE
  • Page 25 – Figure 21. Hole and New Framing Members
  • Page 26 – Figure 23. Attic Firestop
  • Page 27 – Figure 24. Round and Trapezoid Termination
  • Page 28 – =AREA WHERE TERMINAL IS NOT PERMITTED; Figure 25. Vent Termination Minimum Clearances
  • Page 31 – Securing of a Fireplace; Standing Pilot Ignition and Direct
  • Page 32 – Figure 28. Gas Controls Systems; • Locate the gas line access hole in the outer casing of
  • Page 34 – Figure 30. Standing Pilot Ignition Wiring Diagram
  • Page 35 – Figure 31. Fan Wiring Diagram
  • Page 36 – Figure 33. Minimum Vertical and Maximum
  • Page 37 – Figure 34. Sealant Material; Hearth Extensions
  • Page 38 – Placing the Ember Material
  • Page 39 – Lift the trim door up; Figure 35. Glass Assembly; Figure 36. Placement of the Ember Material
  • Page 41 – IMPORTANT
  • Page 42 – Figure 37. Burner Flame Patterns
  • Page 43 – Standing Pilot Only; PART
  • Page 44 – DSI Ignition Only
  • Page 45 – Both Standing Pilot and DSI Ignition; GLASS SPECIFICATIONS:
  • Page 46 – Accessories
Loading the manual

WARNING

IF THE INFORMATION IN
THESE INSTRUCTIONS IS
NOT FOLLOWED EXACTLY, A

FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY,
OR LOSS OF LIFE.

- Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this
or any other appliance.

- What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's
instructions.

• If you cannot reach your gas supplier, call the

fire department.

- Installation and service must be performed by a

qualified installer, service agency, or the gas
supplier.

Heat-N-Glo Fireplace

Models:

8000 DVTFL

6000 DVTFL

6000 XLT

6000 ARCH

SL-42 DVT

U.S. Patents 4,793,322; 4,875,464; 5,000,162 and Patents Pending
Canadian Patent 1,297,746

Installers Guide

WARNING: IMPROPER
INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR
MAINTENANCE CAN CAUSE
INJURY OR PROPERTY DAMAGE.
REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL
INFORMATION CONSULT A
QUALIFIED INSTALLER, SERVICE
AGENGY, OR THE GAS SUPPLIER.

Underwriters Laboratories Listed

484-980-B 7/97

READ THIS MANUAL BEFORE INSTALLING

OR OPERATING THIS APPLIANCE. THIS

INSTALLERS GUIDE MUST BE LEFT WITH

APPLIANCE FOR FUTURE REFERENCE.

1.

This appliance may be installed in an

aftermarket, permanently located,

manufactured (mobile) home, where

not prohibited by local codes.

2. This appliance is only for use with the

type of gas indicated on the rating

plate. This appliance is not convertible

for use with other gases, unless a

certified kit is used.

Please contact your Heat-N-Glo Fireplace
dealer for any questions or concerns. For the
number of your nearest Heat-N-Glo dealer,
please call 612-890-8367.

Printed in U.S.A.

Copyright 1997,
Heat-N-Glo Fireplace Products, Inc.
6665 West Highway 13, Savage, MN 55378

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - SAFETY AND WARNING INFORMATION

i SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Firepla...

Page 3 - ii; Section 5: Replacement Parts

ii Table ofContents Safety and Warning Information ................... i Section 1: Approvals and Codes ................... 1 Approval Listings and Codes ............................ 1 Appliance Certification .................................. 1Installation Codes .......................................

Page 4 - Appliance Certification; CERTIFICATION; Installation Codes

1 Approval Listingsand Codes Appliance Certification The Heat-N-Glo fireplace models discussed in thisInstallers Guide have been tested to certificationstandards and listed by the applicable laboratories. CERTIFICATION MODEL LABORATORY TYPE STANDARD 8000DVTFL Underwriters Direct Vent ANSI Z21.50•CGA...

Other Heat & Glo Models

All Heat & Glo Other