Grizzly Industrial G0719 - Manual

-4- model g0719 (mfg. since 10/10) model G0719 15" disc sander w /stand © Grizzly Industrial, Inc. • Customer Service: (800) 523-4777 • Website: www.grizzly.com macHine data sHeet Product Dimensions: Weight ............................................................................................

-6- model g0719 (mfg. since 10/10) For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tanc...

-8- model g0719 (mfg. since 10/10) additional safety for Disc sanders pOsitiOn taBLE COrrECtLy. make sure the gap between the table and sanding disc does not exceed 3 ⁄ 16 "—too large of a gap increases the risk of workpiece grab and pinch injuries, while too small of a gap increases the risk of...

model g0719 (mfg. since 10/10) -9- sECtiOn 2: pOWEr suppLy availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize t...

model g0719 (mfg. since 10/10) -11- Wear safety glasses dur- ing the entire setup pro- cess! this machine presents serious injury hazards to untrained users. read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! sECtiOn 3: sEtup the foll...

-12- model g0719 (mfg. since 10/10) inventory The following is a description of the main compo-nents shipped with your machine. Lay the compo-nents out to inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, re...

model g0719 (mfg. since 10/10) -13- The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleani...

-14- model g0719 (mfg. since 10/10) site Considerations figure 5. minimum working clearances. 26" 4" 20" 30" Minimum Minimum Dust Port Wall Wall 33.5" Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is ...

model g0719 (mfg. since 10/10) -15- figure 8. door w/panel installation. figure 9. Foot installation. assembly When assembling this machine, we recommend tightening fasteners with hand tools only. Air or electric impact tools can easily over-tighten fas-teners, causing them to dig into the paint or ...

-16- model g0719 (mfg. since 10/10) figure 10. sander installation. figure 11. Fully assembled sander. 6. With the help of another person, place the sanding unit onto the top of the cabinet, as shown in figure 10 , and fasten it to the cabi- net using (4) m8-1.25 x 45 hex bolts and (4) 5 ⁄ 16 " ...

model g0719 (mfg. since 10/10) -17- 6. turn the machine OFF . 7. remove the switch disabling key, as shown in figure 14 . test run once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. the test run consists of verifying the following: ...

-18- model g0719 (mfg. since 10/10) sECtiOn 4: OpEratiOns Operation Overview The purpose of this overview is to provide the nov-ice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to...

model g0719 (mfg. since 10/10) -19- the model g0719 sander accepts 15" diameter adhesive-backed sanding discs. these are avail- able in a variety of grits. the sanding disc sticks to the surface of the cast iron disc platen, using the pressure-sensitive adhesive (psA) backing. the sandpaper can ...

model g0719 (mfg. since 10/10) -21- ACCessories sECtiOn 5: aCCEssOriEs prO-stiCk ® abrasive surface Cleaners extend the life of your sanding discs and sleeves! Choose the pro-stick ® with a handle for greater control or without a handle for more usable area. size Model 1 1 ⁄ 2 " X 1 1 ⁄ 2 " ...

-22- model g0719 (mfg. since 10/10) sECtiOn 6: MaintEnanCE always disconnect power to the machine before performing maintenance. failure to do this may result in serious person- al injury. For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructi...

-26- model g0719 (mfg. since 10/10) table tilt Calibration When the table is perpendicular to the sanding disc, the scale should read 0˚. if not, follow this procedure. tools needed: machinist's square ............................................. 1phillips head screwdriver ............................

model g0719 (mfg. since 10/10) -27- these pages are current at the time of printing. however, in the spirit of improvement, we may make chang-es to the electrical systems of future machines. study this section carefully. if there are differences between your machine and what is shown in this section...

model g0719 (mfg. since 10/10) -29- sECtiOn 9: parts REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PWR1013 WRENCH 10 X 13 21 PB03M HEX BOLT M8-1.25 X 16 2 P0719002 MOTOR BRAKE ASSEMBLY 22 P0719022 STAND LOWER SHELF 2-1 P0719002-1 COMPRESSION SPRING 23 P0719023 STAND SIDE PANEL 2-2 P0719002-2 SPACE...

-30- model g0719 (mfg. since 10/10) 101 102 103 104 105 106 107 109 108 Machine Labels safety labels warn about machine hazards and ways to prevent injury. the owner of this machine Must maintain the original location and readability of the labels on the machine. if any label is removed or becomes u...

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

Warranty anD rEturns Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!