Page 2 - © 2002 Kalatel, a GE Interlogix company; All Rights Reserved.; Tech Support
© 2002 Kalatel, a GE Interlogix company All Rights Reserved. Any GE Interlogix, Kalatel division, software supplied with GE Interlogix, Kalatel division, products is proprietary and furnished under license and can be used or copied only in accordance with the terms of such license. This document con...
Page 3 - UTP M
Rugged Dome Camera Installation Manual Table of Contents 1038346B / February 2003 3 T ABLE OF C ONTENTS B EFORE Y OU B EGIN ............................................................... 4 1 P REPARING THE H OUSING AND C AMERA ............................ 5 1.1 R ETROFITTING WITH THE UTP M ODULE .....
Page 4 - EFORE; A basic knowledge of CCTV systems and components; Customer Support; Improper use of this equipment can cause equipment damage.
Before You Begin Rugged Dome Camera Installation Manual 4 1038346B / February 2003 B EFORE Y OU B EGIN Read these instructions before installing or operating this product. Note: This installation should be made by a qualified service person and should conform to local codes. This manual provides ins...
Page 5 - To retrofit your unit with the UTP module, proceed to section 1.1.; Figure 1. Interior of housing
Rugged Dome Installation Manual Preparing the Housing and Camera 1038346B / February 2003 5 1 P REPARING THE H OUSING AND C AMERA Using the provided Allen wrench, loosen the tamper-resistant housing cover screws. • If your unit has the factory-installed flying lead with coaxial video cable, proceed ...
Page 6 - ETROFITTING WITH THE; ODULE; ) Disconnect the flying lead from the PC assembly and remove it
Preparing the Housing and Camera Rugged Dome Installation Manual 6 1038346B / February 2003 1.1 R ETROFITTING WITH THE UTP M ODULE To put the unit in UTP mode see Figure 2 and perform the following. 1) Disconnect the flying lead from the PC assembly and remove it from the housing. 2) Disconnect the ...
Page 7 - Figure 3. Inserting the mounting screw into the UTP module; ) Screw the UTP module onto the UTP module mounting post; Connection to the PC assembly; ) Attach the UTP cable to the PC assembly.
Rugged Dome Installation Manual Preparing the Housing and Camera 1038346B / February 2003 7 To install the UTP module see Figure 3 and Figure 4 and perform the following. M3.5x3 fillister-head screw Figure 3. Inserting the mounting screw into the UTP module 1) Insert the M3.5x3 fillister-head mounti...
Page 8 - OUNTING THE; Pendant mount
Mounting the Unit Rugged Dome Installation Manual 8 1038346B / February 2003 2 M OUNTING THE U NIT Cables should be prepared and accessible at the mounting location. Figure 5. Surface-mount Figure 6. Flush-mount To surface-mount the housing see section 2.1. To flush-mount the housing see section 2.2...
Page 9 - ) Trace the position of the mounting holes.
Rugged Dome Installation Manual Mounting the Unit 1038346B / February 2003 9 2.1 S URFACE -M OUNTING THE H OUSING To surface-mount the housing, see Figure 8 and perform the following. Mounting surface Anchors Outer plate Inner plate M4x20 truss-head tapping screws (3) M4x12 pan-head double-washer sc...
Page 10 - To mount the outer plate, perform the following.
Mounting the Unit Rugged Dome Installation Manual 10 1038346B / February 2003 5) If necessary, cut out the outlined back cable entry hole. To mount the outer plate, perform the following. 1) Install the provided mounting anchors in the mounting holes. 2) Mount the plates to the anchors in the mounti...
Page 11 - ) Remove the ceiling panel from the ceiling.; installation location.
Rugged Dome Installation Manual Mounting the Unit 1038346B / February 2003 11 2.2 F LUSH -M OUNTING THE H OUSING To flush-mount the housing, see Figure 9 and perform the following. Back plate Ceiling panel Outer plate Inner plate M5x20 pan-head double-washer screws (3) M4x12 pan-head double-washer s...
Page 13 - To prepare the mounting surface perform the following.; ) Using the bracket surface as a template, mark the mounting holes; on the mounting surface.; ) Drill the mounting holes and a pass-through hole for the camera; Pendant or wall-mount; Figure 10. Installing the housing into the bracket
Rugged Dome Installation Manual Mounting the Unit 1038346B / February 2003 13 2.3 U SING P ENDANT - AND W ALL -M OUNT B RACKETS To install the housing on pendant-mount, extended-pendant-mount, or wall-mount brackets, perform the following. Note: The extended-pendant-mount bracket is extended with a ...
Page 14 - ) Remove the three mounting screws from the pendant of the; corresponding holes in the bracket.
Mounting the Unit Rugged Dome Installation Manual 14 1038346B / February 2003 1) Remove the three mounting screws from the pendant of the mounting bracket. 2) Let the housing cover drop down and rest on the hinge. 3) Feed the cables through the bracket. 4) Slide the housing into the pendant of the m...
Page 15 - OAXIAL; Figure 11. Camera cables; ABLE; Figure 12. Cable connections to the PC assembly
Rugged Dome Installation Manual Making Cable Connections 1038346B / February 2003 15 3 M AKING C ABLE C ONNECTIONS To make cable connections using the flying lead with coaxial cable see section 3.1. To make cable connections using UTP see section 3.2. 3.1 C OAXIAL C ABLE To make remaining cable conn...
Page 16 - DJUSTING THE; OCUS; ) Turn the zoom ring to set the desired zoom.; HASE; Phase adjust up; Figure 13. Adjusting the line-lock phase on the PC assembly
Adjusting the Camera Rugged Dome Installation Manual 16 1038346B / February 2003 4 A DJUSTING THE C AMERA To adjust the camera focus see section 4.1. To make phase adjustments see section 4.2. To make auto-iris lens adjustments see section 4.3. 4.1 F OCUS 1) Loosen the zoom ring thumbscrew. 2) Turn ...
Page 18 - UTO; Figure 14. Adjusting the DC level on the PC assembly
Adjusting the Camera Rugged Dome Installation Manual 18 1038346B / February 2003 4.3 A UTO I RIS L ENSES For auto iris lenses, use an insulated adjustment tool to adjust the DC level with the blue pot on the PC assembly (Figure 14). Proper adjustment will ensure the correct exposure depending on the...
Page 20 - LOSING THE
Closing the Housing Rugged Dome Installation Manual 20 1038346B / February 2003 5 C LOSING THE H OUSING Shut the housing cover and use the provided Allen wrench to tighten the housing cover screws. Ensure that the cover is tightened securely to maintain the unit’s IP66 ratings.