Furuno PP-505 - Manual - manualsarea.com

Page 2 - SAFETY INSTRUCTIONS; Do not place heater near the equipment.; Electrical shock can result.; Use the correct fuse.; WARNING; ELECTRICAL SHOCK HAZARD; CAUTION; Safety Information for Operator

i SAFETY INSTRUCTIONS WARNING Do not open the cover ofthe equipment. This equipment uses highvoltage electricity which canshock or burn.Only qualified personnelshould work inside theequipment. Do not disassemble or modify theequipment. Fire, electrical shock or serious injury canresult. Immediately ...

Page 3 - ii; WARNING LABEL

ii A warning label is attached to the printer. Do not remove the label. If the label is missing or damaged,contact your dealer about replacement. WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. Name: Warning Label (1)Type: 86-003-1011Code No.: 100-236-231 WA...

Page 4 - iii; FOREWORD; A Word to the Owner of the PP-505; Selectable printing interval.

iii FOREWORD A Word to the Owner of the PP-505 Congratulations on your choice of the FURUNO PP-505 Printer. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our exten...

Page 5 - iv; TABLE OF CONTENTS; Mount; APPENDIX REPLACEMENT OF PRINTER ASSEMBLY/THERMAL HEAD AP-1

iv TABLE OF CONTENTS 1. OPERATION .................................................................................................. 1 1.1 General ..............................................................................................................................1 1.2 Panel ..................

Page 6 - Indicators; GRAPH

1 1. OPERATION 1.1 General Operation of the PP-505 is simple; just turn on the power. The depth graph or the log, whichever is selected for printing, is printed out at the interval set. Below are example printouts. 60m 80m 100m 20m 40m Marker 2003/12/01 13:05:00 038.6m/01.0m 35 20.02’N/135 45.15’E 1...

Page 7 - OPERATION; Changing the mode; Turning on the Power

OPERATION 2 Changing the mode Press the [MODE] key to change the printing mode from depth graph to log printing alternately. The printing interval setting is printed whenever the [MODE] key is pressed. Changing the printing interval Press the [INTERVAL] key to choose printing interval. Depth graph: ...

Page 8 - Red mark; Remedy for paper jam

3 2. REPLACEMENT OF THERMAL PAPER When the thermal paper runs out, the PAPER LED blinks, printing stops automatically and the audible alarm sounds for five seconds. With 1 m of paper remaining, a red paper end mark appears on the paper. When the red mark appears, replace the thermal paper as shown i...

Page 9 - Set; Name; Main Unit; Mounting; Water spray

4 3. INSTALLATION 3.1 Complete Set Name Type Mass Qty Remark Main Unit PP-505 3.1 kg(with hanger) 1 Spare Parts SP08-01600 1 Installation Materials CP16-00800 1 Accessories FP08-00500 1 Flush Mount Kit OP08-4 1 Option (004-511-330) 3.2 General Mounting Considerations This equipment can perform its i...

Page 10 - Tabletop mount; Bulkhead mount; Name Type

3. INSTALLATION 5 3.3 Tabletop/Bulkhead Mount The main unit can be mounted on a desktop, bulkhead, or in a panel. Make sure the selected location is strong enough to support the main unit against possible vibration and shock. If necessary, appropriate reinforcement measures should be made on the mou...

Page 12 - Checking the power connector; Diagnostic test

7 4. MAINTENANCE Checking the power connector Check for loosened or disconnected power connector. WARNING Do not open the cover of the equipment. This equipment uses high voltage electricity which can shock or burn.Only qualified personnel should work inside the equipment. Do not disassemble or modi...

Page 14 - Hold the flexible cable end with a

AP-2 6. Pull out the connector end of the flexible cable from the connector. Take care not to damage the flexible cable. End of FlexibleCable (Connector) 180 ° 7. Remove the thermal head from the head holder with a screwdriver as shown below, and then take the thermal head assembly out of the printe...

Page 15 - Fix the flexible cable to the carriage with; Fold back the end of the cable and insert

AP-3 11. Fix the flexible cable to the carriage with the flexible cable support, inserting the projection on the carriage into the hole of the cable. Flexible Cable Support Carriage Projection 12. Fold back the end of the cable and insert it into the connector. End of FlexibleCable 180 °

Page 16 - FURUNO; SPECIFICATIONS OF PRINTER

FURUNO SP - 1 E5540S03-1 SPECIFICATIONS OF PRINTER PP-505 1 DATA FORMAT 1.1 Receiving System RS-232C 1.2 Speed 9600 bps 1.3 Data Length 8 bits 1.4 Parity Non 1.5 Stop Bit 1 bit 2 PRINTER SECTION 2.1 Printing System 9 dots serial thermal head printing system 2.2 Character Alphanumeric 2.3 Dot Pitch 0...

Furuno PP-505 - Manual

Table of Contents:

Summary

Other Furuno Models