Page 3 - IMPORTANT NOTICES; General; How to discard this product; In the European Union; Cd; Pb
i IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international us- ers. • The operator of this equipment must read and follow the descriptions in this manual. Wrong op- eration or maintenance can cancel the warranty or cause injury. • Do not c...
Page 4 - ii; SAFETY INSTRUCTIONS; Prohibitive Action; Safety Instructions for the Operator; WARNING
ii SAFETY INSTRUCTIONS Indicates a condition that can cause death or serious injury if not avoided. Indicates a condition that can cause minor or moderate injury if not avoided. Use the proper fuse. Use of a wrong fuse can cause fire or damage to the equipment. Handle the LCD monitor with care. The ...
Page 5 - iii; Safety Instructions for the Installer; About the TFT LCD
SAFETY INSTRUCTIONS iii Safety Instructions for the Installer WARNING WARNING CAUTION CAUTION Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. Do not install the equipment where it may get wet from rain or water spl...
Page 6 - iv; TABLE OF CONTENTS
iv TABLE OF CONTENTS Note: This manual contains both English and Japanese instructions. The Installation Materials, Outline Drawings, and Interconnection Diagram are located at the back of this manual . FOREWORD ...........................................................................................
Page 7 - FOREWORD; A Word to the Owner of the MU-190; Features; Program
v FOREWORD A Word to the Owner of the MU-190 FURUNO Electric Company thanks you for purchasing the MU-190 19” Monitor Unit. We are con-fident you will discover why the FURUNO name has become synonymous with quality and reliabil-ity. For over 60 years FURUNO Electric Company has enjoyed an enviable r...
Page 8 - SYSTEM CONFIGURATION
vi SYSTEM CONFIGURATION Connectable equipment Note 1: Landscape orientation only. Note 2: *: When inputting VGA, SVGA or XGA, a circle may be displayed as an ellipse because the aspect ratio differs (see "DISP MODE*" on page 15). Equipment Resolution Signal FCV-1200L/1200LM VGA* Analog RGB, ...
Page 9 - vii; EQUIPMENT LISTS; Standard supply
vii EQUIPMENT LISTS Standard supply Optional supply Name Type Code No. Qty Remarks Monitor Unit MU-190 - 1 Installation Materials CP26-01600 000-019-210 1 set • Installation Materials (CP26-01601, Code No.: 001-116-250, See page A-1.) • Cable Assembly (DVI-D/D S-LINK 5M, Code No.: 001-132-960-10) Ac...
Page 10 - Preparation; Mounting method; Mounting location; Run cables before installing the monitor unit
1 1. MOUNTING, WIRING 1.1 Preparation Mounting method You can install the monitor unit as follows. See the outline drawings at the back of this manual for mounting dimensions. • Flush mount, fixed at front (standard)• Flush mount, fixed at front, with hood (option)• Flush mount, fixed at rear (optio...
Page 11 - Flush Mount, Fixed at Front
1. MOUNTING, WIRING 2 1.2 Flush Mount, Fixed at Front Flush mount, fix at front is the standard installation method. 1. Use the flush mounting template (supplied) to make a cutout in the mounting location.2. Attach the flush mounting sponges H19 and V19 to the back of the monitor unit in the order s...
Page 12 - How to attach or detach the masking panel for 19” LCD
1. MOUNTING, WIRING 3 7. Set the masking panel to each side of the monitor unit. How to attach or detach the masking panel for 19” LCD Do the following to attach or detach the masking panel for 19” LCD. 1.3 Flush Mount, Fixed at Front, with Hood The flush mount, fixed at front method allows you to a...
Page 14 - Flush Mount, Fixed at Rear
1. MOUNTING, WIRING 5 7. Set the cutouts of the hood (19) assembly to the knobs on the hood fixing plates (19). 8. Press the top of the hood (19) assembly to set the knobs in the cutouts. 9. Set the hood (19) assembly with the knobs tightly (4 pcs.). 1.4 Flush Mount, Fixed at Rear The flush mount, f...
Page 17 - Tabletop Mount
1. MOUNTING, WIRING 8 6. Set the cutouts of the hood (19) assembly to the knobs on the hood fixing plates 19. 7. Press the top of the hood assembly to set the knobs in the cutouts. 8. Set the hood assembly with the knobs tightly (4 pcs.). 1.6 Tabletop Mount You can fix the monitor unit to a tabletop...
Page 18 - How to attach the hood
1. MOUNTING, WIRING 9 2. Set the mounting bracket to the mounting location with four self-tapping screws. 3. Attach the bracket support to the rear of the monitor unit with the binding head screws (9 pcs.). 4. Connect all cables at the back of the monitor unit. See section 1.8.5. Loosen the knobs of...
Page 19 - Flush Mount a Series Side by Side
1. MOUNTING, WIRING 10 1.7 Flush Mount a Series Side by Side You can flush mount two or three monitor units side by side, using the optional flush mount kit OP26-13 for two monitor units or OP26-14 for three monitor units (see page vii). 1. Make a cutout in the mounting location as shown below (see ...
Page 20 - Wiring; Connector; How to fix power cable
1. MOUNTING, WIRING 11 1.8 Wiring Refer to the figure below and the interconnection diagram at the back of this manual to connect cables. Connector *1: Attach a crimp-on lug (inner dia. φ 4) for monitor unit side. Make the length of the ground wire as short as possible. *2: Slide switch • ON (upward...
Page 21 - ADJUSTMENTS; Installation Settings
12 2. ADJUSTMENTS Adjust the MU-190 according to the equipment connected. Note: Sections 2.2, 2.3 and 2.4 are for Non-SOLAS. 2.1 Installation Settings The [INSTALLATION SETTING] menu appears only when the power is turned on for the first time after installation. For ECDIS (FEA-2107) or chart radar (...
Page 23 - How to open the [INSTALLATION SETTING] menu
2. ADJUSTMENTS 14 How to open the [INSTALLATION SETTING] menu Turn off the monitor unit. While you hold the DISP key, press the /BRILL key to turn on the mon- itor unit. Press and hold the DISP key for more than five seconds. Note: When the "DVI PWR SYNC" slide switch is ON, turn on the conn...
Page 26 - How to adjust the menu window
2. ADJUSTMENTS 17 2.4 The Menu Window Setting (For Non-SOLAS) 2.4.1 How to adjust the menu window You can adjust the position and transparency of the menu window on the [OSD] (On Screen Dis-play) menu. 1. Press the MENU key to show the menu. 2. Press the W or X key to select [OSD]. 3. Press the S or...
Page 27 - How to change the signal name
2. ADJUSTMENTS 18 2.4.2 How to change the signal name You can change the signal name ([RGB], [DVI1/2] or [VIDEO]) to a name (ex. the equipment name) which is easy to understand. The name is shown in the DISP selection window and the indication shown at the upper right of the screen (see section 3.4)...
Page 28 - OPERATION; Controls; Turn the power on/off
19 3. OPERATION Note: When you connect the monitor unit to FAR-21x7, FEA-2107 or FCR-21x7, you can turn the power on/off and adjust the brilliance via the application of the FAR-21x7, FEA-2107 or FCR-21x7 only (see section 2.1). 3.1 Controls The dimmer for the power LED and keys changes with the dis...
Page 29 - Unlock the key operation; How to Adjust the Display Brilliance
3. OPERATION 20 Slide switch “ON” The external equipment connected to the DVI port (DVI-D1 or DVI-D2) can turn on/off the monitor unit. See the operator’s manual for the external equipment connected. Note 1: You can not turn on the power with the /BRILL key on MU-190. Note 2: When you connect the ca...
Page 30 - How to Select the Source for Main Picture; How to Display the PIP Window; SYSTEM Menu; How to set the auto dimmer
3. OPERATION 21 3.4 How to Select the Source for Main Picture Select the signal to display on the entire screen as follows: 1. Press the DISP key to show the DISP selection window. The window shows the signal names as you customized them at paragraph 2.4.2. This window disappears if there is no oper...
Page 31 - How to clear the memory
3. OPERATION 22 2. Press the X key to select [SYSTEM]. 3. Press the S or T key to select [AUTO DIMMER]. 4. Press the W or X key to select an interval to check brightness. Note: When you connect the monitor unit to FAR-21x7, FEA-2107 or FCR-21x7, set to [OFF]. 5. Press the MENU key to close the menu....
Page 32 - Maintenance; Routine maintenance; NOTICE
23 4. MAINTENANCE,TROUBLESHOOTING 4.1 Maintenance Routine maintenance Regular maintenance is important for good performance. Check the following on a regular basis to keep the equipment in good condition. Fuse replacement The fuse in the fuse holder at the bottom of the display protects the equipmen...
Page 33 - Parts location; ELECTRICAL PARTS
4. MAINTENANCE, TROUBLESHOOTING 24 4.2 Troubleshooting See the following table to find the possible causes of trouble and the actions to restore normal operation. If repair of the equipment is necessary, report the result of the troubleshooting to the service technician. 4.3 Parts Location and Parts...
Page 34 - FURUNO; SPECIFICATIONS OF MONITOR UNIT
FURUNO MU-190 SP - 1 E3519S04C SPECIFICATIONS OF MONITOR UNIT MU-190 1 GENERAL 1.1 Display 19-inch color LCD 1.2 Effective area 376.32 x 301.06 mm 1.3 Resolution SXGA (1280 x 1024 pixel) 1.4 Pixel pitch 0.294 mm (Horizon/Vertical) 1.5 Brightness 450 cd/m 2 typical 1.6 Contrast 900: 1 1.7 View angle ...
Page 35 - 工事材料表
CODE NO. 001-116-250-00 TYPE CP26-01601 略 図 OUTLINE 名 称 NAME 数量 Q'TY 用途／備考 REMARKS 番 号 NO. 型名／規格 DESCRIPTIONS 1/1 -2 INSTALLATION MATERIALS 工事材料表 26AH-X-9401 MU-190 FﾏｳﾝﾄｽﾎﾟﾝｼﾞV19 FLUSH MOUNTING SPONGE V 19 26-005-3124-0 2 100-351-560-10 1 CODE NO. 化粧ﾊﾟﾈﾙ19 MASKING PANEL FOR 19" LCD 26-007-112...
