Fujitsu M3093GX - Manual

iv 5.3.1 Cleaning the document cover, document holding pad, and document bed ........ 5-2 5.3.2 Cleaning the ADF ............................................................................................... 5-3 5.4 Consumables/Periodical replacement parts .............................................

v FIGURES page 2.1 Received components ................................................................................................. 2-1 2.2 M3093EX/GX parts names ......................................................................................... 2-2 2.3 M3093EX/GX Indicators ...............

vi TABLES page 1.1 The differences between the M3093EX and the M3093GX ....................................... 1-1 3.1 SCSI-ID setting ........................................................................................................... 3-6 6.1 Check items ........................................

1 – 1 CHAPTER 1 PREFACE This manual describes how to operate the M3093EX and M3093GX image scanners. An imagescanner optically reads image information from a document and outputs the information to thehost system. The differences between the M3093EX and the M3093GX image scanners arelisted in table ...

2 – 1 CHAPTER 2 COMPONENTS 2.1 Checking the Components 2.2 Part Names and Functions 2.3 Indicator Panel Functions After unpacking image scanner, confirm that all the components have been received. Thissection describes the components of the image scanner and their functions. 2.1 Checking the Compone...

2 – 2 2.2 Part Names and Functions This section shows the exterior view of image scanner. This sectionalso provides names of each part and describes their functions. 2.2.1 Exterior view of image scanner The image scanner can read a document of A4 or letter size at maxi-mum. Figure 2.2 M3093EX/GX par...

2 – 3 2.2.2 Functions of each part Document cover: Closed over and holds a document to beread. Document bed: A document to be read is placed on thebed also called Flatbed (FB). Document holding pad: Presses a document to the document bed. Automatic document feeder (ADF): Automatically feeds document...

2 – 4 2.3 Indicator Functions Figure 2.3 M3093EX/GX Indicators 2.3.1 Indicators The meaning of each indicator is as follows: Power indicator (Green): Lights to indicate the power is on. Read (reading in progress) indicator (Green): Lights to indicate reading is in progress. Check (device check) indi...

3 – 1 CHAPTER 3 INSTALLATION AND CONNECTIONS This chapter explains how to install and connect the image scanner. 3.1 Precautions Do not install the image scanner in the following places and environ-ments. See the appendix A.1 “Installation Specifications” for theinformation such as size of installat...

3 – 2 3.2 Removing the Carrier Fixing Bracket To keep the scanner from being damaged during shipping, the carrierunit is fixed with a bracket. After placing the carrier unit at theinstallation place, remove this bracket as explained below. 1 Place the image scanner on the edge of the desk top so tha...

3 – 3 3.3 Connections Connect the image scanner using the following procedure. 1 Set the power switch to off. 3 Connect the interface cables (for M3093EX). Connect the interface cables to the interface connectors and fasten the cableswith catches and screws as shown below.Connect the other end of ea...

3 – 5 3.4 Mounting the Stacker Mount the stacker using the following procedure. Hook the pins on the stacker to the holes of the image scanner. → Push ← Push

4 – 1 CHAPTER 4 OPERATIONS 4.1 Turning on the Power 4.2 Reading a Document in Flatbed Mode 4.3 Reading Documents in ADF Mode Documents can be read in the flatbed mode or automatic document feeder (ADF) mode. In theflat-bed mode, each document is placed on the document bed and is read one by one. In ...

4 – 2 4.2 Reading a Document in Flatbed Mode This section explains how to read a document placed on the documentbed. 4.2.1 Reading a standard-size document If the size of the document is smaller than the document bed, read thedocument using the following procedure: 1 Open the document cover. 2 Place...

4 – 3 Document cover Reference mark Figure 4.1 Flatbed reading Document bed Document 4.2.2 Reading a page from a thick book To read a page from a thick book, remember the following points: 1 Do not close the document cover forcibly. Keep the cover openfor reading. 2 Any document parts that are not i...

4 – 4 4.2.3 Reading a document larger than the document board If the size of the document is larger than the document board, read thedocument using the following procedure: 1 Open the document cover at an angle of about 80°, then slide thecover to the direction of the arrow to remove it. 2 Place the...

4 – 5 4.3 Reading Documents in ADF Mode This section explains how to read documents using the automaticdocument feeder. If the following steps are not closely followed, afeed error may occur. 1 Check the documents as follows: (a) Paper quality • Wood-free paper.• PPC paper; Specified by XEROX Corpor...

4 – 6 (THICK mode) (NORMAL mode) Paper select lever ADF frame Section A enlargerd NOTICE: Paper should be straightened to fit the condition below. Top of the paper More than30 mm Less than5 mm Read surface Feed direction Read surface Feed direction Top of the paper More than30 mm Less than5 mm 2 Swi...

4 – 7 3 Pull up the ADF paper chute as follows: • Hold the document cover with one hand and pull up the ADF paper chute with the other hand until it clicks. Push for storage ADF paper chute Shaft Document cover Figure 4.3 ADF paper chute setting ADF paper chute Document cover 4 Fan the documents as ...

4 – 9 7 Open the right and left guides of the ADF paper chute about 5mm wider than the document width. 8 Place the documents face down onto the ADF paper chute withthe top edges facing the automatic feeder hole. 9 Adjust the guides to the document sides. Skewing may occur ifthere is a gap between th...

5 – 1 CHAPTER 5 MAINTENANCE 5.1 Removing Jammed Documents 5.2 Notes on Daily Use 5.3 Cleaning 5.4 Consumables/Periodical replacement parts ADF lever Automatic document feeder (ADF) Figure 5.1 Removing jammed documents This section explains how to remove jammed documents, and provides notes on daily ...

5 – 4 5.4 Consumables / Periodical replacement parts 5.4.1 Parts number and replacement cycle Customer is responsible to change these items periodically. Part number PA02201-0020 PA02212-K001(*2) Part name Pad ASY Pick roller Replacement cycle Every 100,000 pages or annually(*1) Every 200,000 pages ...

5 – 5 3 Insert the pad assembly into the ADF frame hole (the bigger one),slide the assembly to the direction of the arrow until it clicks. Pad assy ADF frame NOTICE: Pad can be replaced by aligning the holes of the pad with the pins of the Pad holder. Figure 5.4 Pick Roller replacement Guide A Thumb...

5 – 6 Figure 5.5 Move the Retaining spring A direction Retaining Spring Bearing A c. Pinch the retaining spring and slide it toward the roller. Freebearing A from the bracket bysliding it toward the roller. d. Slide the pick roller shaft in the direction of arrow B and removethe shaft from bearing B...

6 – 1 Possible cause The power switch was notturned on. The power cable was notconnected correctly. —————————— The documents were notplaced on the ADF correctly. The ADF was not closedcompletely. The interface cables were notconnected correctly. Terminator was not con-nected. (M3096GX). Halftone pro...

A – 1 APPENDIX A A.1 Installation Specifications Table A.1 Installation specifications Specification Item External dimensions (mm) Weight (kg) Height 173 11 100 to 120 VAC, 200 to 240 VAC Single-phase 50/60 Hz 100 VA Input power Depth 376 Width 530 Voltage Number of phases Frequency Power Operation ...

A – 2 A.2 External Dimensions (Unit: mm) Figure A.1 External dimensions 376 530 173

B – 1 APPENDIX B B.1 Test mode for maintenance CAUTION: Please follow the procedure here or the offset data may be changed incor- rectly. If the scanner does not react as the procedure below, turn off thescanner and start from the beginning. (1) Activating a test mode Open the ADF cover and set the ...

B – 2 (2) Activating the continuous operation test Open the ADF and close it again. If no document is loaded on the ADF within five sec-onds after closing the ADF, the image scanner runs in flatbed mode. If documents areloaded on the ADF within five seconds after closing the ADF, the image scanner c...

C – 1 APPENDIX C C.1 Option Name Specification Scanner Feature IPC-2 CA01952-0191 M3093EX Image processing M3093GX • Automatic separation• Image emphasis• Outline extraction• Mirror image• Dynamic threshold• Noise suppression• Smoothing CMP-2 CA M3093GX • 4 Mbyte memory• MH/MR/MMR compression Contac...

C – 2 (5) Remove the two screws in the following figure. (6) Remove the four screws from the interface connector and remove the two screws A in the following figure. (7) Remove the cover from the interface PCA. (8) Connect the IPC-2 option board connector and tighten the screw. Two screws Screw A In...

Reader Comment Form We would appreciate your comments and suggestions for improving this publication. Clean How did you use this publication? Is the material presented effectively? Learning Installing Sales Fully Well Well Reference Maintaining Operating Covered illustrated Organized Publication No....