Ford 2010 Transit Connect - Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

may seek to access the information independently of Ford MotorCompany and Ford of Canada. To the extent that any lawpertaining to Event Data Recording applies to SYNC 威 or its features, please note the following: Once 911 Assist (if equipped)is enabled (set ON), 911 Assist may, through any paired an...

CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Brake system warning light: To confirm the brake system warninglight is functional, it willmom...

Safety belt: Reminds you to fasten your front driver and passengersafety belt. A Belt-Minder 威 chime will also sound to remind you tofasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder 威 chime feature. Charging system: Illuminates when t...

GAUGES Speedometer: Indicates the current vehicle speed. Tachometer: Indicates the engine speed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the engine. Instrument Cluster 17 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Print...

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range. If it enters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, switchoff the engine and let the engine cool. If it enters...

Information display 1. Distance to empty / clock: Registers the approximate distancethe vehicle can travel beforerefuelling is necessary. Clock showsthe current set time. Switching the display between“clock” and “distance toempty”: • Vehicles with “clock” displayednormally: Press the Select button(4...

AUDIO SYSTEMS AM/FM stereo (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the saf...

Sound Adjustments Press MENU repeatedly to cycle through the following features: BASS: Press to adjust the level of bass. TREBLE: Press to adjust the level of treble. BALANCE: Press to adjust the audio between the left (L) and right (R) speakers. FADE: Press to adjust the audio between the back (B) ...

MENU: Press repeatedly to access the following features: MAN: Press < or > to manually advance down or up the chosen frequency band. SCAN: Press < or > for a brief sampling of radio stations or CD tracks. SHUFFLE CD: Select to shuffle the tracks on the current CD. REPEAT CD: Select to re...

The auxiliary input jack allows youto connect your portable musicplayer and play music through thevehicle speakers with high fidelity. Required equipment: 1. Any portable music playerdesigned to be used withheadphones 2. An audio extension cable withstereo male 1/8 in. (3.5 mm)connectors at each end...

portable music players have different output levels, so not all playersshould be set at the same levels. Some players will sound best at fullvolume and others will need to be set at a lower volume. 3. If the music sounds distorted at lower listening levels, turn theportable music player volume down....

Voice recognition Your Bluetooth system is equipped with a voice recognition system which allows you to perform some operations by speaking certaincommands to the system. The system will respond with a series of beeps,confirmations or questions when necessary. At any time, you can say,“Cancel” if yo...

Microphone Your vehicle has a microphonelocated in the A-pillar for thehands-free phone features and voicecommands. To mute the microphone: During an active call, press < or > on theaudio system. Press again toun-mute and return to normalfunction. Voice commands Voice commands allow you to spe...

Making a call using voice commands To make a hands-free call using your system: 1. Press the VOICE button on the stalk. 2. When the tone sounds, say, “Phone”. The system will confirm you arein phone mode. 3. Say, “Dial name” or “Dial number”. 4. When prompted, say the desired name or phone number. T...

To accept the incoming call, press the button on the audio system. To reject the incoming call, by pressing CD or AM/FM on the audio system. Redialing a number To redial a number: 1. Press on the audio system to enter the phone menu. 2. Press MENU repeatedly to cycle through CALL OUT, CALL IN,MISSED...

3. Press < or > on the audio system to scroll through the list of paired(bonded) phones. 4. When the desired selection appears in the display that you would liketo delete, press MENU. GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communicatio...

• Wipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and...

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Temperature control: Controls the temperature of the airflow in the vehicle. For optimum defrosting performance, set the dial to the defrostsymbol . 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a bri...

4. Recirculated air: Press to activate/deactivate air recirculation in the vehicle cabin. Recirculated air may reduce the amount of timerequired to cool down the interior of the vehicle and may also helpreduce undesired odors from reaching the interior of the vehicle.Recirculated air will not functi...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument p...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Rear fog lamp The headlamp control also operatesthe rear fog lamp. The rear fog lampcan only be turned on when theheadlamp control is inthe position. P...

VERTICAL AIM ADJUSTMENT 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from thecenter...

Replacing interior bulbs Check the operation of all bulbs frequently. Replacing front dome lamps 1. Make sure the headlamp switch isin the off position. 2. Switch off the interior lamps. 3. Pry out the light assembly with aflat screwdriver. Install in reverse order. Replacing rear dome lamps 1. Make...

Replacing reading bulbs 1. Open the reading lamp assembly. 2. Pull the bulb straight out andreplace it. 3. After the bulb has been replaced,close the lamp assembly. Install in reverse order. Replacing exterior bulbs Check the operation of all bulbs frequently. Replacing headlamp bulbs 1. Make sure t...

3. Remove the bulb socket from thelamp assembly by turning itcounterclockwise. 4. Pull the bulb straight out of thesocket. Install in reverse order. Lights 47 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)

MULTI-FUNCTION LEVER Windshield wiper Move the lever down for a singlewipe. For intermittent operation, move control up one position andadjust the rotary control to thedesired speed. For normal operation, move control up two positions and upthree positions for high speedwiping. Windshield washer To ...

OVERHEAD STORAGE SHELF The storage shelf above thewindshield can be used for storinglight objects such as safety jackets,coats, etc. WARNING: Do not place heavy or hard objects in the overhead storage, which may fall while driving, and could cause serious injury. AUXILIARY POWER POINTS (12VDC) Power...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror: up, down and from side-to-side. Push the tab to help reduce glare atnight. WARNING: Do not adjust the mirror while the vehicle is in motion. EXTERIOR MIRRORS Power side view mirrors...

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Setting speed control The controls for using your speedcontrol...

• Depress the brake pedal until thedesired vehicle speed is reached,press SET +. Turning off speed control Press OFF. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) The following functions can be operated...

Seek Move the SEEK switch up or down: • In radio mode, this will locate thenext radio station up or down thefrequency band. • In CD mode, it will select thenext or previous track. Mode Briefly press the button on the side: • In radio mode, this will locate thenext pre-set radio station. • In CD mode...

DUAL REAR DOORS Open the right hand door first fromeither the outside (1) or inside (2)the vehicle. Open the left hand door second bysqueezing the handle to unlatch thedoor and pulling it open. 1 2 Driver Controls 59 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)

Note: The dual rear doors should be closed before driving your vehicle. Leaving the doors open could cause serious damage to them and theircomponents. The left door must be closed first. Opening the doors fully Push the yellow button located onthe door and swing it open. Thecheck arms will automatic...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. If your vehicle is equipped with the SecuriLock™ Passive Anti-theftsystem, your keys are electronically coded to your vehicle; using anon-coded key wil...

Two-step door unlocking • Press and release to unlock the passenger doors. • Within three seconds, press and release again to unlock all the doors. Note: The interior lamps will illuminate if the control on the overhead lamp is not set to the off position. One-step door unlocking If the one step doo...

Replacing the battery The remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent. To replace the battery: 1. Carefully separate the transmitterunit from the key using a flat object(e.g. a screwdriver) at the recess onthe back. 2. Open the transmitter unit bysepara...

7. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmittershould operate normally after battery replacement. Replacing lost remote entry transmitters If you would like to have your remo...

Illuminated entry The interior lamps illuminate when the remote entry system is used tounlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the on position, or • the remote transmitter lock control is pressed, or • after 25 seconds...

Anti-theft indicator The anti-theft indicator is located in the instrument cluster. • When the ignition is in the offposition, the indicator will flashbriefly to indicate theSecuriLock™ system isfunctioning as a theft deterrent.The indicator light will stop flashing after approximately 10 seconds. •...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front manual seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Always drive and ride with your seatback upright and the lap belt...

To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as poss...

• Unlocked SAFETY RESTRAINTS Personal Safety System 姞 The Personal Safety System 威 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditi...

are properly restrained. Accident statistics suggest that children aremuch safer when properly restrained in the rear seating positions than inthe front. WARNING: Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use ...

Front outboard safety belt energy management retractors The front safety belt energy management retractors allow webbing to bepulled out of the retractor in a gradual and controlled manner inresponse to the occupant’s forward momentum. This helps reduce therisk of force-related injuries to the occup...

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) until you hear a snap and feel itlatch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. To unfasten, push the release ...

Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. This mode should be used any time a ch...

WARNING: After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which does not have this feature) must be checked by an authorized dealer toverify that the automatic locking retractor feature for child seats is stillfunctioning properly. In additio...

WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safetybelt and increase the risk of injury in a collision. Safety belt warning light and indicator chime The ...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

1. Turn the ignition switch to the on position. DO NOT START THEENGINE. 2. Wait until the safety belt warning light turns off (Approximately1–2 minutes). • Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. Buckle then unbuckle the driver’s safety belt nine t...

WARNING: Additional equipment may affect the performance of the airbag sensors increasing the risk of injury. Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment. Children and airbags Children must always be properlyrestrained. Ac...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

A difficulty with the system is indicated by one or more of the following: • The readiness light will eitherflash or stay lit. • The readiness light will notilluminate immediately afterignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the p...

WARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. WARNING: If the side airbag has deployed, the airbag will not function again.The side airbag system(including the seat) must beinspected and serviced by anauthorized dealer. If the airbag is not re...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

Each time you use the safety seat, check that the seat is properlyattached to the lower anchors and tether anchor, if applicable. Tug thechild seat from side to side and forward and back where it is secured tothe vehicle. The seat should move less than one inch when you do thisfor a proper installat...

• Five-passenger vehicle Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct tether anchor. Once the child safety seat has been installed, using either the safety beltor the lower anchors of the LAT...

2. Locate the anchor for the centerseating position. 3. Clip the tether strap to theanchor as shown. Second-row outboard seating positions 1. Remove the head restraint. For instructions on how to remove thehead restraint, refer to Second row adjustable head restraints earlier in this chapter. Note: ...

• On four-passenger vehicles theanchor is located on thedriver-side upper rear door framearea close to the roof. 3. Clip the tether strap to theanchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision. 4. Tighten the c...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a p...

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

WARNING: The Tire Pressure Monitoring System is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge,see Inflating your tires in this chapter. Failure to properly maintain your tire pressure could increase the ri...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low TirePressureWarning Light Possiblecause Customer Action Required Flashing WarningLight Spare tire inuse Your temporary spare tire is inuse. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a description ofhow the system functions underthese condition...

under-inflated, carefully drive the vehicle to the nearest location whereair can be added to the tires. Inflate all the tires to the recommendedinflation pressure. TPMS reset procedure The TPMS reset procedure needs to be performed after each tirerotation. WARNING: To determine the required pressure...

2. Place the ignition in the off position and keep the key in the ignition. 3. Cycle the ignition to the onposition with the engine off. 4. Turn the hazard flashers on thenoff 3 times. This must beaccomplished within ten seconds. If the reset mode has been entered successfully, the horn will soundon...

8. Remove the valve cap from the valve stem on the right rear tire.Decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire.Decrease the air pressure until the horn sounds. Training is complete after the horn sounds for the last tire trained(...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires, Wheels and Loading 147 2010 Transit Conne...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

you have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat folded down, you have room for12-100 lb. (45 kg) bags of cement. Do you have enough load capacityto transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation ...

RECREATIONAL TOWING Follow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehicle behinda motorhome. These guidelines are designed to ensure that yourtransmission is not damaged. Note: Put your climate control system in recircu...

STARTING Positions of the ignition 1. O (off) — locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. This position also shuts theengine and all electrical accessoriesoff. 2. I (accessory) — allows theelectrical accessories such as theradio to operate while the engine...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or adjust the heatingor air conditioning to bring in fresh air. ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coola...

Parking brake To set the parking brake (1), pullthe parking brake handle up as faras possible. The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. WARNIN...

During Traction Control events the “sliding car” icon in the instrument cluster will flash. If the Traction Control system is activated excessively in a short periodof time, the braking portion of the system may become temporarilydisabled to allow the brakes to cool down. In this situation, Traction...

During an event that activates the Roll Stability Control™ (RSC 威 ) the “sliding car” icon in the instrument cluster will flash. Certain adverse driving maneuvers may activate the Roll Stability Controlsystem, which include: • Emergency lane-change • Taking a turn too fast • Quick maneuvering to avo...

the van on a regular basis. These drivers will gain valuable experiencehandling the van. This experience will help make each trip safer. The van should be operated at a safe speed which, in some conditions,may be less than the posted speed limit. Further, all occupants should be properly restrained....

BRAKE-SHIFT INTERLOCK This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the on position unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Park) with ignition inthe on ...

AUTOMATIC TRANSMISSION OPERATION Understanding the gearshift positions of the 4–speed automatictransmission This vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive Shift Strategy offers the optimal transmission operation andshift quality. When the vehicle’s battery has been di...

The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the figures forapproximate zone coverage areas).As you move closer to the obstacle,the rate of the tone increases. Whenthe obstacle is less than 10 inches...

When driving through water, traction or brake capability may be limited.Also, water may enter your engine’s air intake and severely damage yourengine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into thetransmission and cause int...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch isaccessible from behind the g...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

Have a flat serviced by an authorized dealer in order to prevent damageto the TPMS sensors, refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing ofthe flat tire, have the a...

• Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to im...

Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as soon as possible. Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)and turn engine off. Removing the spare tire Th...

3. Detach the first cable by pullingup the cap and sliding it away fromthe wheel. Then turn the end of thecable so it fits through the slot andremove the cable and bracket. 4. Detach the second cable byunscrewing the bolt. Tire change procedure WARNING: When one of the front wheels is off the ground...

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m M12 x 1.5 66 90 * Torque specifications are for nut and bolt threads free o...

JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your aut...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Pr...

• Some automatic car washes may cause damage to the finish on yourwheel rims or covers. Chemical-strength cleaners, or cleaningchemicals, in combination with brush agitation to remove brake dustand dirt, could wear away the clearcoat finish over time. • Do not use hydrofluoric acid-based or high cau...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). WINDOWS AND W...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth, then use a clean and dry white cottoncloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portionof the instr...

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). In Canada, useMotorcraft Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the rin...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Lift and swivel the hood badgeback. 2. Insert the key and turn it to theleft to release the primary latch.Then, turn they key to the right torelease the secondary latch. Note: To prevent damage to, or loss of the key, remove the keyimmediately after opening the hoodand swivel the...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Engine oil filler cap 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Windshield washer fluid reservoir 7. Air filter assembly 8. Automatic transmission fluid dipstick 9. Engine oil dipstick 10. Power st...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil ...

• If the oil level is between the MIN and MAX marks , the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MINmark, add enough engine oil toraise the level within the MIN andMAX range. Refer to Adding engine oil in this chapter. • Oil levels above MAX markmay cause engine dam...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interval s...

• Add Motorcraft Specialty Orange Engine Coolant withBittering Agent, or equivalent meeting Ford specificationWSS-M97B44-D. Refer to Maintenance product specifications and capacities in this chapter. • Do not add/mix a Yellow or Green type of engine coolant suchas Motorcraft Premium Gold Engine Cool...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely col...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol, leadedfuel or any other fuel. The use of leaded fuel is prohibited by law andcould damage your vehicle. Your vehicle was not designed to use fuel or ...

empty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might no...

economy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general, lower temperatures give lower fuel economy. Driving style — good driving and fuel economy habits Give consideration to the lists that follow and ...

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example bugdefl...

for 15 seconds without cranking the engine. If the service enginesoon indicator blinks eight times, it means that the vehicle is not ready for I/M testing; if the service engine soon indicator stays on solid, it means that the vehicle is ready for I/M testing. The OBD-II system is designed to check ...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

4. Place the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifnecessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure...

If necessary, add fluid in 1/2 pint (250 ml) increments through the fillertube until the level is correct. After adding fluid, wait 20 minutes beforechecking the fluid level in order to allow the level to stabilize. If an overfill occurs, excess fluidshould be removed by an authorizeddealer. If the ...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A AdvanceTrac ..............................160 Air cleaner filter ...............240–241 Airbag supplemental restraintsystem ..................................92, 101 and child safety seats ..............94description ........................92, 101disposal ....................................103dr...

V Vehicle Identification Number(VIN) ..........................................247 Vehicle loading ..........................146 Ventilating your vehicle ...........156 W Warning lights (see Lights) .......12 Washer fluid ..............................214 Water, Driving through .............170 Wind...