Ford 2010 Taurus - Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

information”) only to help provide you with the directions, trafficreports, or business searches you request. If you do not wantFord or its vendors to receive this information, do not activatethe service. Ford Motor Company and the vendors it uses toprovide you with this information do not store you...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Standard instrument cluster shown, optional cluster similar Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many...

Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic co...

Low washer fluid (RTT): Illuminates when the washer level inthe washer fluid reservoir is low. Door ajar (RTT): Illuminates in the message center display whenthe ignition is in the run positionand any door is open. Trunk ajar (RTT): Illuminates in the message center display whenthe ignition is in th...

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the off or accessory position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is ope...

MESSAGE CENTER Your vehicle’s message center allows you to configure/personalize certainvehicle options to suit your needs. The message center is also capable of monitoring many vehicle systemsand will alert you to potential vehicle problems and various conditionswith an informational message follow...

If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic...

System check and vehicle feature customization Press the SETUP button repeatedlyto cycle the message center throughthe following features: RESET FOR SYSTEM CHECK When this message appears, press RESET and the message center willbegin to cycle through the following systems and provide a status of the...

3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET button to change the Oil Life Start Value. Each release and presswill reduce the value by 10%. Note: Oil life start value of 100% equals 7,500 miles (12,000 km) or 12 months. For example, setting oil life start value to 60% sets...

Press RESET to turn the warning chime on or off. The system will revertto chime on each time the vehicle is started. The heads up display and/orchime will activate briefly to confirm the last setting. COLLISION WARN SYSTEM (if equipped) This feature warns the driver of a possible collision. See Coll...

INTKEY COULD NOT PROGRAM — Displayed when an attempt is made to program a fifth integrated key to the remote key entry system.For more information on integrated key, refer to the Locks and Security chapter in this manual. CRUISE ON RADAR READY (if equipped) — Displayed when the driver pressed the cr...

AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford...

Setting the clock To set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and minutes. The clock will then beginfrom that time. AM/FM Radio / VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decreas...

LOAD:For a single CD system– This control is not operational. To load aCD, simply insert the disc, label side up, into the CD slot. For a CD6 system– Press LOAD. When the display reads SELECT SLOT, choose the desired slot number using memory presets 1–6. Whenthe display reads LOAD CD #, load the des...

CAT (Category) / FOLD(Folder): Press to toggle between turning the most recently selectedsatellite radio category on or off. The category icon (CAT) will illuminatein the display when a specific category is selected (the icon will notilluminate during CATEGORY ALL). If no category has ever beenselec...

OK. The song will appear in the display for confirmation. Press OKagain and the display will read SONG DELETED. If you do not wantto delete the currently listed song, press SEEK to select either RETURN or CANCEL. Note: If there are no songs presently saved, the display will read NO SONGS. c. DELETE ...

d. RESET PIN: Press OK when RESET PIN is displayed. The display will read ARE YOUR SURE. Press OK again to automatically reset thePIN number to its initial password setting (1234). PIN RESET TODEFAULT PIN will be displayed. e. RETURN: Press OK when RETURN is displayed and the system will exit back t...

Required equipment: 1. Any portable music player designed to be used with headphones 2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connectors at each end To play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. En...

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the portable music player should be stored in a securelocation, such as the center console or the glove box, when the vehicle isin motion. The audio exte...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thundersto...

Do not use any irregular shapedCDs or discs with a scratchprotection film attached. CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker r...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna. You are in a location that i...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear th...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. + Fan speed control: Press to increase the fan speed. 2. Defrost: Distributes outside air through the windshield defros...

Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. CLIMATE: Press to control the climate control system through the touch display screen. See Touchscreen functions later in this section. 2. R Rear defroster: Press to activa...

• : Distributes air through the floor vents, rear seat floor vents. • : Distributes air through the windshield defroster vents, de-mister vents, floor vents and rear seat floor vents. The system willautomatically provide outside air to reduce window fogging. To return to full automatic control, pres...

For maximum cooling performance: • Automatic operation: 1. Press AUTO for full automatic operation. 2. Do not override A/C or (recirculated air). 3. Set the temperature to 60°F (16°C). • Manual operation: 1. Select MAX A/C. 2. Select (panel) or (panel/floor). 3. Select (recirculated air) to provide ...

CABIN AIR FILTER The cabin air filter element is designed to reduce the concentration ofairborne particles such as dust, spores and pollen in the air beingsupplied to the interior of the vehicle. The presence of a particulate filterelement provides the following benefits: • Improves your driving com...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled b...

3. Turn the ignition switch to on and then back to off. 4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. High beams Push the lever toward theinstrument p...

Operation - The high beam switch can be used to turn the high beams on. They will then remain on until the switch has been returned to theneutral position and the auto high beam system has turned the highbeams off. Scenario 3: Conditions - The automatic high beam system is set to ON in the message c...

For significant blockages (e.g. bird dropping, bug splatter, snow, or ice),the automatic high beam system uses a blocked sensor computerprogram. If it detects a blockage, it will be monitored for two minutes. Ifno changes are observed, the system will go into low beam mode untilthe blockage is clear...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicablelit components in the vehicle duringheadlamp and parking lampoperation. • Tap the top or bottom of thecontrol to brighten/dim all interiorlit components incrementally, or • Press and hold the top or bottom of ...

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. To see a clearer light pattern for adjusting, you may want to block thelight from one headlamp while adjusting the other. 4. On the wall or screen you willobserve an area of high intensitylight. The top of the high ...

INTERIOR LAMPS Dome lamps and map lamps The map lamps are located on theoverhead console. Press the controlson either side of each map lamp toturn on the lamps. Your vehicle may also have readinglamps within the rear dome lamp(s). Press the switches on either side ofthe dome lamp to turn on thereadi...

BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product of this design. When moist airenters the lamp assembly through the vents, there is a possibility thatcondensation can occur when the temperature is...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Rain sensing wipers (ifequipped): The rain sensing wipers will automatically activate whenmoisture is present on thewindshield ...

Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining onthe windshield. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluidlevel frequ...

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on thevisor mirror lamp. Slide on rod feature The visor will slide back and forthon the rod for increased sunlightcoverage. Rotate the visor towardsthe side window and extend itrearward for additional sunlightcoverage. Note: To stow the visor ba...

ELECTRONIC COMPASS (IF EQUIPPED) The compass heading is displayed in the center stack display. The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objects placed in, on or near the vehicle may also affectcom...

4. Press and release the 7 and 9radio preset buttons together,repeatedly until ZONE XX changesto the correct zone (1–15) in theCID. 5. The direction will display afterthe buttons are released. The zoneis now updated. Compass calibration adjustment Perform compass calibration in an open area free fro...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Note: The appearance and features of the center console may be different thanshow based on your vehicle’s option level. These include: • Cupholders • Utility compartment with audioinput jack, USB port and powerpoint • Pe...

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse. Do not hang any type of accessory oraccessory bracket from the plug. Improper use of the poweroutlet can cause damage ...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or bu...

Driver’s and passenger’s windowone-touch up or down (ifequipped) To operate one touch-down: • Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press theswitch to any position to stop thewindow operation. If the switch is pressed and held...

and the window will travel up with no bounce-back or pinch protection. If the switch is released before the window is fully closed, the window will stop. For example, this can be used to overcome theresistance of ice on the window or seals. Window lock The window lock feature allows onlythe driver t...

Automatic dimming interior rear view mirror (if equipped) Your vehicle may be equipped with an interior rear view mirror that hasan auto-dimming function. The electronic day/night mirror will changefrom the normal (high reflective) state to the non-glare (darkened) statewhen bright lights (glare) re...

Blind spot mirrors (if equipped) Your vehicle may be equipped with blind spot information mirrors. See Blind Spot Information System 威 (BLIS 威 ) with Cross Traffic Alert (CTA) in the Driving chapter. Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an auto...

WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel. The followingbuttons work with speed control: RESUME: Press to resume a set speed. SET +: Press to increase the set spee...

WARNING: Always pay close attention to changing road conditions, especially when using Adaptive Cruise Control. Adaptive Cruise Control cannot replace attentive driving. Failing tofollow any of the warnings below or failing to pay attention to the roadmay result in a collision, serious injury or dea...

3. Press and release the SET +control. The vehicle speed will bestored in the memory and themessage center will display SETXXX MPH (your desired speed). 4. Take your foot off the acceleratorpedal. 5. The green cruise indicator light on the instrument cluster willilluminate if there are no vehiclesde...

Cause Action The surface of the radar in thegrille is dirty or obstructed insome way Clean the grille surface in front ofthe radar or remove the objectcausing the obstruction The surface of the radar in thegrille is clean but the messageremains in the display Wait a short time. It may takeseveral mi...

STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features VOL + (Volume): Press to increase the volume. VOL – (Volume): Press to decrease the volume. (Seek): Press to select the previous/next radiostation preset, CD track or satelliteradio channel preset depending onwhich media mode you are in. M...

SYNC 威 system hands free control feature (if equipped) Press briefly to use the voice command feature. You will hear atone and LISTENING will appear inthe radio display. Press andhold to exit voice command. Press to activate phone mode or answer a phone call. Press andhold to end a call or exit phon...

To open the moon roof: Press and release the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof. WARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the mo...

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink 威 buttons be erased for security purposes, refer to Programming in thi...

5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the pres...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

To erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outsideCar2U 威 system buttons simultaneously for approximately20 seconds until the indicator lightsbegin to blink rapidly. The indicatorlights are located directly a...

INTERIOR TRUNK CONTROL The trunk release button is locatedon the instrument panel near theradio. Press the button to open thetrunk. CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided. Do notput more than 50 lb...

KEYS Integrated Keyhead Transmitters (IKTs) (If equipped) Your vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle andunlocks/locks all the doors. Thetransmitter portion functions as theremote entry transmitter. Yo...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart unlocks This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors and you lock the vehicle with thepower d...

If your vehicle’s perimeter alarm is in the armed state, the smart unlockfeature will not allow you to lock your IA key inside the trunk. When thealarm is armed, if the IA key is detected in the trunk, the decklid willautomatically be released when you attempt to close it, and the horn willchirp, as...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition off. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user will receive a horn chirp to ind...

Keyless entry keypad autounlock enable/disable procedure 1. Turn the ignition off. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a second ti...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the oper...

WARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people oranimals to these high temperatures for even a short time can causedeath or serious heat-related injuries,...

Intelligent Access key Refer to Intelligent Access in this section for more features. Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. The typical operating range for your transmitter is approximately 33 f...

Intelligent Access (if equipped) WARNING: Radio waves from the Intelligent Access system transmitters in the vehicle may affect certain implanted medical devices such as pacemakers or cardiac defibrillators. People havingsuch implanted medical devices should ask the medical devicemanufacturer or the...

Push button start: Your vehicle is equipped with a push button start system, which allows you to start your vehicle without using a key. Tooperate the push button start system and start your vehicle, your IA keymust be present inside the vehicle, either in the passenger compartmentor in the trunk. R...

Car finder Press twice within three seconds. The horn will chirp and the turn lamps will flash. It is recommended that this method be used to locateyour vehicle, rather than using the panic alarm. Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash f...

2. Press and hold either the 1 or 2control located on the seat sideshield for five seconds. (A tone willbe heard after 1 1 ⁄ 2 seconds when the memory store is done) continue tohold until a second tone is heardafter five seconds. 3. Within three seconds pressthe on the transmitter. 4. A tone will be...

2. Remove the old battery. Note: Please refer to local regulations when disposing oftransmitter batteries. 3. Insert the new battery. Refer tothe instructions inside the IKT forthe correct orientation of thebattery. Press the battery down toensure that the battery is fully seated in the battery hous...

Replacing lost Integrated Keyhead Transmitters (IKTs) or IntelligentAccess Keys (IA keys) If you would like to have your IKTs or IA keys reprogrammed becauseyou lost one, or would like to buy additional transmitters you can eitherreprogram them yourself, or take all transmitters to your authorized d...

Battery saver The battery saver will shut off the lamps 10 minutes after the ignitionhas been turned off. • If the dome lamps were turned on using the panel dimmer control, thebattery saver will shut them off 10 minutes after the ignition has beenturned off. • If the courtesy lamps were turned on be...

SECURICODE™ KEYLESS ENTRY SYSTEM The keypad, located near the driver’s window, is invisible until touchedand then it lights up so you can see and touch the appropriate buttons. Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more ...

two-stage unlocking, refer to the Central Unlocking/Two stage unlocking section earlier in this chapter. To unlock all doors, enter the factory set code or your personal code, then press the 3 • 4 control within five seconds. Note: If equipped with Intelligent Access, if the Intelligent Access Key i...

engine. If a problem occurs, turn the ignition off, remove all objects onthe key chain away from the coded key and restart the engine. Note: Do not leave a duplicate coded key in the vehicle. Alwaystake your keys and lock all doors when leaving the vehicle. Anti-theft indicator The anti-theft indica...

Replacement Integrated Keyhead Transmitters (IKT) and codedkeys or Intelligent Access Keys Note: Your vehicle comes equipped with two Integrated Keyhead Transmitters (IKTs) or two Intelligent Access Keys. The Integrated Keyhead Transmitter (IKT) functions as both a programmed ignition key that opera...

Note: To program MyKey™ features, refer to MyKey™ in this chapter. MYKEY™ The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey™. The key will remain restricteduntil MyKey™ is dis...

Create a MyKey™ To program MyKey™ on one of the keys programmed to the vehicle,insert it into the ignition. (For vehicles equipped with push button start,put the Intelligent Access Key in the backup slot; see the Driving chapter for the location of the backup slot.) Turn the ignition on. Usethe mess...

Arming the system When armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash theturn signal lamps and will sound the horn. The system is ready to arm whenever the ignition is off. Any of thefollowing actions will prearm the alarm sys...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your transmitter. • Unlock the doors by using your keyless entry pad. • Turn ignition to the on position with a valid programmed SecuriLock™key or Integrated Keyhead Transmitter (IKT). • If eq...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

Press either up or down on thelumbar control to select the top,middle, or bottom part of the seatback. Press the front of the lumbarcontrol to increase the firmness ofthe selected portion of the seatbackand press the rear of the lumbar todecrease the firmness. We recommend first selecting the lumbar...

Press the control to recline theseatback forward or rearward. Using the power lumbar support (if equipped) The power lumbar control is locatedon the outboard side of the seat. Press one side of the control toadjust firmness. Press the other side of the controlto adjust softness. Dual setting heated ...

To operate the cooled seats: Press once to activate the high coolsetting (three indicator lights).Continue pressing to scroll throughthe other settings; medium cool(two indicator lights), low cool (one indicator light) or off. The cooled seats will turn off after 30 minutes. If the engine falls belo...

3. Remove filter. To install a filter: 1. First, position the filter in it’shousing making sure that the farforward end is all the way up in thehousing. 2. Push in on the center of theoutside edge of the filter and rotateup into the housing until it clips intoposition. Memory seats/power mirrors/adj...

2. Simultaneously press and holdboth the adjust/release button andthe unlock/remove button, then pullup on the head restraint. To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. Properly a...

The indicator light will illuminate when the heated seats have beenactivated. SAFETY RESTRAINTS Personal Safety System 姞 The Personal Safety System 威 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-relate...

appropriate to activate these safety devices. Front airbags are designedto activate only in frontal and near-frontal collisions (not rollovers, sideimpacts or rear impacts) unless the collision causes sufficientlongitudinal deceleration. The pretensioners are designed to activate infrontal and near-...

WARNING: Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag dep...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, driver seatposition sensor, and front passenger sensing system. In addition, theRCM also monitor...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the ...

2. To unfasten, press the releasebutton and remove the tongue fromthe buckle. All restraints in the vehicle are combination lap and shoulder belts. While you are fastened in the safety belt, the combination lap/shoulderbelt adjusts to your movement. However, if you brake hard, turn hard, orif your v...

Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. This mode should be used any time a ch...

How to disengage the automatic locking mode WARNING: Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify thatthe ⬙ automatic locking retractor ⬙ feature for child seats is still worki...

WARNING: The driver and front passenger safety belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results indeployment of front airbags, seat-mounted side airbags and SafetyCanopy 威 , and safety belt pretensioners. Safety ...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km/h) and more than1-2 minutes have elapsed sincethe ignition has been switchedon... The Belt-Minder 威 feature is activated - the safety belt warning l...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t...

• This will enable the Belt-Minder 威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light willflash four times per second for three seconds, followed by threeseconds with the light off, then followed by the safety belt warninglight flashing fo...

Important supplemental restraint system precautions Airbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest close tothe trim covering the airbag module. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belt...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbagsdid not inflate in a collision does n...

• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions, • the system determines that a small child is present in a forward-facingchild restraint that is installed according to the manufacturer’sinstructions, • the ...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the cond...

WARNING: Do not attempt to service, repair, or modify the Safety Canopy 威 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy 威 . See your authorized dealer. WARNING: All occupants of the vehicle including the driver should always wear their safety...

WARNING: If the Safety Canopy 威 system has deployed, the Safety Canopy 威 will not function again unless replaced.The Safety Canopy 威 system (including the A, B, C, and Dpillar trim and headliner) must beinspected and serviced by anauthorized dealer. If the SafetyCanopy 威 is not replaced, it will not...

The SOS Post-Crash Alert can be turned off when any one of thefollowing actions are taken by the driver or any other person: • pressing the hazard control button, • or pressing the panic button on the remote entry transmitter. The feature will continue to operate until the vehicle runs out of power....

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier,convertible seat,or toddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

restrained properly, then restrain the child in the child safety seat orwith the belt-positioning booster. Remember that child seats andbelt-positioning boosters vary and may be designed to fit children ofdifferent heights, ages and weights. Children who are too large for childsafety seats or belt-p...

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol. The LATCH anchors are located atthe rear section of the rear seatbetween the cushion and seatback,below the locator symbols on theseat back. Follow the child seatmanufacturer’s...

Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap whichextends from the back of the child safety seat and hooks to an anchoringpoint called the top tether anchor. Tether straps are available as anaccessory for many older safety seats. Conta...

3. Open the tether anchor cover. 4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If the ...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The Tire Pressure Monitoring System is NOT a substitute for manually checking tire pressure. The ...

When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to identify an issue to remind youthat the damaged road wheel/tire needs to be repaired and put back onyour vehicle. To restore the full functionality o...

Low TirePressureWarning Light Possiblecause Customer Action Required FlashingWarning Light Spare tire inuse Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle to restoresystem functionality. For a descriptionof how the system functions underthese conditio...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

SUMMER TIRES Your Taurus SHO may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud and Snow (M+S or M/S) tire traction rating on the tire sidewall. Since summer tires do not have the same traction performance asAll-season or Snow tires...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. Tires, Wheels and Loading 225 2010 Taurus (500) Owners Guide (own2002) , 1st Printing USA (fus)

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (9 x45 kg) = 635 - 198 - 405 = 32 kg. The above calculations also assume that the loads are position...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

• It is recommended to select the L (Low) gear position when additionalengine braking is needed. In situations such as prolonged downhilldriving on steep grades (i.e., driving in mountainous areas), additionalengine braking is needed to reduce the load on the vehicle’s regularbrake system to prevent...

Front Wheel Drive (FWD) vehicles: Tow your Front Wheel Drive vehicle with all four wheels on the groundor with the front wheels off the ground by using a tow dolly. If you areusing a tow dolly follow the instructions specified by the equipmentprovider. All Wheel Drive (AWD) vehicles: Tow your All Wh...

STARTING Positions of the ignition (if equipped) If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessorie...

3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive. Note: If the engine does not start on the first try, turn the vehicle to the off position, wait 10 seconds and try Step 2 again. If the engine still failsto start, press the accelerator to the fl...

vehicle from the on mode. If you would like to start the vehicle and youare in on mode, you must first switch the vehicle off. 4. Start — press the START/STOP button (for any length of time) whileapplying the brake pedal. Note: The indicator light on the start button will illuminate when the vehicle...

the message center. You can re-start the vehicle (by applying the brakepedal and pressing the START/STOP button) for up to 20 seconds, eventhough the IA key is not present. After 20 seconds have expired, you canno longer start your vehicle without the IA key present inside thevehicle. Switching the ...

Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control during emergency stops bykeeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking ...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released....

Switching Off AdvanceTrac 威 If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the AdvanceTrac 威 system may be beneficial because the wheels are allowed to spin. This will restore fullengine power and will enhance momentum through the obsta...

AdvanceTrac 威 Features Controlswitchfunctions Mode “Sliding car off” icon Message Center Display (if equipped) ESC Traction Control Controlswitchpressed andheld formore thanfiveseconds,vehiclespeed =0 mph,brakesapplied AdvanceTrac 威 Disabled (SHO with Performance Pack Only) On ADVANCETRAC OFF Disabl...

• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir. If the steering wanders or pulls equipped with either EPS or Hydraulicsteering system, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspe...

N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position. D (Drive) The normal driving position for the best fuel economy. Transmissionoperates in gears one through six. M (Manual) With the gearshift lever in...

Recommended shift speeds Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6 50 mph (80 km/h) The instrument cluster will show thecurrent...

Image delay if displayed through the rearview mirror: When shifting out of R (Reverse) and into any other gear, the image inthe rearview mirror will remain on for a few seconds before it shuts offto assist in parking or trailer hookup. Image delay if displayed through the Navigation screen: After sh...

Night time and dark area use At night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is necessary that bothreverse lamps are operating in order to get a clear image in the dark. Ifeither of the lamps are not operating, stop using the cam...

Operation The radar sensor detects vehiclesahead that are moving in the samedirection as your vehicle. If the radar detects that yourvehicle is rapidly closing on anothervehicle a red warning light willilluminate and an audible warningchime will sound. After that, if the risk of collisionfurther inc...

WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressedjust like for any typical braking situation. Blocked sensor If a message regarding a blockedsensor is displayed,...

Note: If the system cannot be turned off in a MyKey™ equipped vehicle, refer to MyKey™ in the Locks and Security chapter for more information. Note: If collision warnings are perceived as being too frequent or disturbing then the warning sensitivity can be reduced, though themanufacturer recommends ...

The CTA system detects vehicles approaching up to 45 feet (14 meters)away (approximately the width of five parking spaces). Coveragedecreases when vehicles and objects in close proximity block the CTAsensors (refer to figure for approximate zone coverage areas [sensor obstructed for vehicle on left]...

the BLIS 威 and/or the CTA is turned off, the message center displays BLIND SPOT SYS OFF and/or CTA SYSTEM OFF. When the BLIS 威 and/or the CTA system is off, the driver will not receive alerts. Refer to Message center in the Instrument Cluster chapter. Note: If the system cannot be turned off, refer ...

Once the blockage is removed, the system will require some driving timeand detection of at least two vehicle objects prior to resetting or thedriver can cycle the ignition key. If, however, blockage is still presentafter the key cycle, the system will sense again that it is blocked afterdriving in t...

ability to anticipate wheel slip and transfer torque to the rear wheelsbefore slip occurs. The AWD system is active all the time and requires noinput from the operator. All components of the AWD system are sealed for life and require nomaintenance. Note: When an AWD system fault is present, the warn...

When driving at slow speeds in deep sand under high outsidetemperatures, use L (Low) gear when possible. L (Low) gear operationwill maximize the engine and transmission cooling capability. Under severe operating conditions, the A/C may cycle on and off toprotect overheating of the engine. Avoid exce...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford MotorCompany joins the U.S. Forest Service and the Bureau of LandManagement in encouraging you to help preserve our national forest andother ...

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy off-...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Customer Information Guidefor information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase exten...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Left front power window, Smartwindow motor 2 15A Brake on/off switch 3 15A Driver power...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the d...

Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)and turn engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcoun...

3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground. Note : DO NOT LIFT ON THE PLASTIC MOLDING, as this coulddamage the molding. ONLY LIFT ONTHE SHEET METAL NOTCH. 4. Remove the lug nuts with the lug wrench. 5. ...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Place theextension bolt into the externalpocket of the felt bag. Take care toposition the jack as shown to ensurethat the locating holes in the jack...

If you are stowing the flat tire: 1. Remove the extension bolt fromthe exterior pocket of the felt bag. 2. Install the jack as shown inStep 4 under Stowing the tire and jack . 3. Screw the extension bolt onto thethreaded stud of the jack retentionbracket. 4. With the temporary spare tire onthe vehic...

• Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle. Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporarymobility kit: • Before operati...

• Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation. What to do when a tire is punctured A tire puncture within the tire’s tread area can be repaired in two stageswith the temporary mobility kit: • In the first stage, the tire will be reinfla...

4. Plug the power cable into the 12Vpower point in the vehicle. 5. Remove the warning sticker found on the canister and place it on thetop of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) . 7. Turn dial (1) counterc...

tire pressure has to be checked with the compressor in the OFFposition to get the correct tire pressure reading. WARNING: Do not stand directly over the temporary mobility kit while inflating the tire. If you notice any unusual bulges or deformations in the tire’s sidewall during inflation, stop and...

4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jam area.Pressing the deflation button nearthe sealant canister removes airfrom the tire. Note: The tire pressure has to be checked with the compressor in theOFF position to get the correct...

Removal of the Sealant Canister from the Temporary Mobility Kit 1. Unwrap the clear tube from thecompressor housing. 2. Press the button located on thetemporary mobility kit compressorhousing below the canister whilepulling up on the sealant canister. Installation of the Sealant Canister to the Temp...

2. Once aligned, seat the sealantcanister by lightly pushing downuntil you hear an audible click. 3. Wrap the clear tube around thecompressor housing. Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorizeddealer f...

Bolt size Wheel lug nut torque* lb.ft. N • m 1/2-20 UNF 100 135 * Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recommended replacement fasteners. WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounti...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Note: Do not attach the negative (-) ...

2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper c...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, su...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

3.5L V6 SHO ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Wipe the surface with a damp, clean, white cotton cloth. For morethorough cleaning, use a mild soap and wate...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • For routine cleaning, wipe the surface with a soft, damp cloth. Formore thorough cleaning, wipe the surface with a mild soap and watersolution. In Canada, use Motorcraft Vinyl Cleaner (CXC-9...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specificat...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap ...

Engine shield Some vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter changes. It is secured withfour screws. WINDSHIELD WASHERFLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the ...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

5. Locate and carefully remove theengine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the...

• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions,...

Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andAp...

For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe battery terminals. If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neut...

Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe battery is disconnected or a new battery is installed, the engine mustrelearn its idle and fuel trim strategy for optimum driveability andperformance. To...

Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. WARNING: Do not add engine coolant when the engine is hot. Steam and scald...

WARNING: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can comeout forcefully when the cap is loosened slightly. Add the proper mixture of coolant and water to the cool...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications...

What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before incremental component damage is incurred.The “fail-safe” distance depends on ambient temperatures, vehicle loadand terrain. How fail-safe cooling work...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuelfiller nozzle. The overfilled fuel may run down the drain located withinthe fuel filler housing and to the ground. If the Check Fuel Fill Inlet message ...

Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may notbe covered under warranty. Octane recommendations 3.5L V6 engine Your vehicle will run normally on 87 octane regular fuel. Premium fuelwill provide improved performance. ...

Running out of fuel Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine....

1. After lifting the trunk cargocover, locate the white plasticfunnel. It is attached to the rear,lower edge of the spare tirecompartment. 2. Slowly insert the funnel into theEasy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container.4. When done, clean the funnel or properly ...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may re...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condition oftransmission fluid may cause shift and/or engagement concernsand/or possible damage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may...

Changing the air filter element 3.5L V6 3.5L V6 (SHO) 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove...

ENGINE DATA Engine 3.5L V6 engine 3.5L V6 SHO engine Cubic inches 214 214 Fuel See Octane recommendations earlier in this chapter. See Octane recommendations earlier in this chapter. Firing order 1–4–2–5–3–6 1–4–2–5–3–6 Ignition system 0.052–0.056 inch (1.32–1.42 mm) 0.033–0.037 inch (.838–.939 mm) ...

TRANSMISSION CODE DESIGNATIONS You can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmission each coderepresents. Description Code 6F 6-Speed Automatic Transmission J 6F55 6–Speed Automatic Transmission (withEcoBoost) C Maintenance and S...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ..........................82 Adaptive Cruise Control .............86 AdvanceTrac ..............................244 AdvanceTrac Sport Mode .........248 Air cleaner filter ...............357–359 Air conditioning ....................48, 51 automatic temperaturecontrol system ............

Transmission .............................251 brake-shift interlock (BSI) ....250fluid, checking and adding(automatic) .............................355 Trunk .........................................117 remote release ................108, 122 Turn signal ..................................65 U Univer...