Ford 2010 Focus - Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide/Customer Information Guide that is provided to you along with your Owner’s Guide. Special instructions For you...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation of their vehicle. Only use cel...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Continued driving ...

Airbag readiness: If this light fails to illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediately by your authorized dealer. A chime will soundwhen there is a malfunction in the indicator light. Safety belt: Reminds you to fasten your safety b...

Overdrive off (if equipped): Illuminates when the overdrivefunction of the transmission hasbeen turned off, refer to the Driving chapter. If the light flashes steadily or does not illuminate, have the transmission serviced soon, or damage may occur. Speed control (if equipped): Illuminates when the ...

Low fuel: Illuminates when the fuel level in the fuel tank is at or nearempty (refer to Fuel gauge in this chapter). Door ajar: Illuminates when the ignition is in the on position and anydoor is open. Turn signal: Illuminates when the left or right turn signal or thehazard lights are turned on. If t...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range. If it enters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, s...

Odometer: Registers the total miles (kilometers) of the vehicle. If equipped with a message center,refer to Message center in this chapter on how to switch thedisplay between Metric and English. Trip odometer: Registers the distance of individual journeys. • Standard instrument cluster: Press the SE...

Info Press the INFO button repeatedly tocycle through the following features: TRIP A/B Registers the distance of individual journeys. Press and release INFObutton until the A or B trip appears in the display (this represents thetrip mode). Press and hold RESET until it resets. Refer to UNITS later i...

• Differences in the automatic shut-off points on the fuel pumps atservice stations • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed controlsystem engaged to ...

7. MYKEY(S) PROGRAMMED 8. ADMIN KEYS PROGRAMMED Note: Some systems show a message only if a condition is present. UNITS Displays the current units in English or Metric. Press RESET to change between English and Metric. AUTOLOCK This feature automatically locks all vehicle doors when the vehicle issh...

AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM/single CD satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. F...

In TEXT MODE: Sometimes the display requires additional text to be displayed. When the < / > indicator is active, press TEXT and thenpress SEEK/TRACK to view the additional display text. CAT (Category) / FOLD (Folder): Press to switch between turning the most recently selected satellite radio ...

The song will appear in the display for confirmation. Press OK againand the display will read SONG DELETED. If you do not want todelete the currently listed song, press / to select either RETURN or CANCEL. Note: If there are no songs presently saved, the display will read NO SONGS. c. DELETE ALL SON...

d. RESET PIN: Press OK when RESET PIN is displayed. The display will read ARE YOUR SURE. Press OK again to automatically reset thePIN number to its initial password setting (1234). PIN RESET TODEFAULT PIN will be displayed. e. RETURN: Press OK when RETURN is displayed and the system will exit back t...

To play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. Ensure that the battery in your portable music player is new or fullycharged and that the device is turned off. 3. Attach one end of the audio extension cable to the headp...

location, such as the center console or the glove box, when the vehicle isin motion. The audio extension cable must be long enough to allow theportable music player to be safely stored while the vehicle is in motion. USB port (if equipped) WARNING: Driving while distracted can result in loss of vehi...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. R Rear defroster: Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this chapter for more information. 3. Defrost: Distributes ou...

9. Temperature control: Controls the temperature of the airflow in the vehicle. 10. Passenger heated seat control (if equipped): Press to activate/deactivate the passenger heated seat. See Heated seats in the Seating and Safety Restraints chapter. 11. Recirculated air: Press to activate/deactivate a...

During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C in theMAX A/C position, reduce blower fan speed from the highest setting andput the vehicle’s transmission into the PARK gear position (automatictransmission only) to...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Fog lamp control (if equipped) The fog lamps can be turned onwhen the headlamp control is inthe or position and the high beams are not turned ...

Rear dome lamp When the lamp control is in themiddle position, the rear dome lampwill come on when a door is openedor the unlock button is pressed onthe remote keyless entry. If the control is moved to the driverside position, the lamp will not comeon at all. If the control is moved to the passenger...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pr...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down until you find thedesired position. 3. While holding the steering wheelin place, pull the lever up to itsoriginal positi...

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

Window lock (if equipped) The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. INTERIOR MIRROR The interior rear view mirror has tw...

EXTERIOR MIRRORS Power side view mirrors (if equipped) WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the direc...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

• Press the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off thespeed control: • Press the speed control OFFcontrol. • Turn off the ignition. Note: When you turn off the speed control or the ignition, your speedco...

To vent the moon roof: Press and release the TILT control, the moon roof will move to the vent position automatically from any moon roofposition. Press the switch again to stop the moon roof. Pull and hold theTILT control to close the moon roof. The moon roof has a built-in sliding shade that can be...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

Power door unlock/lock procedure Before starting, ensure the ignition is in the off position and all vehicledoors are closed. You must complete Steps 1–5 within 30 seconds or theprocedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of 30 seconds before beginning ag...

• Ensure that the trunk is closed and latched before driving yourvehicle. Failure to properly latch the trunk may cause objects to fallout or block the driver’s rear view. Replacing the battery The remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent. To replace...

How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. If all remote entry transmittersare not present during the programming procedure, the transmitters thatare not present during programming will no l...

The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Illuminated exit • When all vehicle doors and the trunk are closed, and the key isremoved from the ignition, the interior lamps and parking lamps willilluminate. The lamps will turn off if all...

key chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded key while starting the engine. Theseobjects will not cause damage to the coded key, but may cause amomentary issue if they are too close to the key when starting theengine. If a problem occurs, turn...

If the key was not successfully programmed, it will not start yourvehicle’s engine and the theft indicator light will flash on and off, or stayon for more than three seconds. If failure repeats, bring your vehicle toyour authorized dealer to have the new key(s) programmed. To program additional new ...

• The AdvanceTrac 威 system cannot be turned off. When this optional setting is on, the MyKey™ user will not be able to deactivate thesystem. Note: It may be beneficial to deactivate the AdvanceTrac 威 system if the vehicle is stuck in snow, mud, or sand. Create a MyKey™ To program MyKey™ on one of th...

Using MyKey™ with Remote Start Systems MyKey™ is not compatible with non-Ford approved aftermarket remotestart systems. If you choose to install a remote start system please seeyour authorized dealer for a Ford approved remote start system. When using a Ford-approved remote start system, the default...

Arming the system When armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash thepark/turn lamps and will sound the horn. The system is ready to arm whenever the key is removed from theignition. Either of the following actions will pr...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front manual seat WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of th...

Tip/slide front passenger seat (if equipped) Lift the control and fold theseatback forward. The seat can be slid forward toallow easier entry to the rear seats.Slide the seat back and fold backthe seatback until it locks with adistinct click. Rock the seat toensure that the catch is securelyengaged....

Lower the head restraint bypressing and holding the guidesleeve release button and pushingdown on the head restraint. For details about the individual components of the head restraints andabout how to remove the head restraints, refer to Adjustable head restraints at the beginning of this chapter. F...

SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System™ provides an improved overall level offrontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and crash ...

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbaginflation energy. A lower, less forceful energy level is provided for morecommon, moderate-severity impacts. A higher energy level is used forthe most severe impact...

The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint us...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, frontpassenger sensing system, and the driver seat position sensor. Inaddition, the RCM also mon...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the ...

2. To unfasten, press the releasebutton and remove the tongue fromthe buckle. Energy management feature • This vehicle has a safety belt system with an energy managementfeature at the front outboard seating positions to help further reducethe risk of injury in the event of a head-on collision. • Thi...

Safety belts with locking cinch tongue (rear center position only) The locking cinch tongue will slide up and down the belt webbing whenthe belt is in the stowed position or while putting safety belts on. Whenthe locking cinch tongue of the lap/shoulder combination safety belt islatched into the buc...

WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belton the outside shoulder only. Never wear the shoulder belt under thearm. 2) Never swing the safety belt aro...

Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch(20 cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the sa...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• safety belt pretensioners • one or more impact and safing sensors. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system later in this chapter. • a readi...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

WARNING: If the side air curtain has deployed, the air curtain will not functionagain. The side air curtainsystem (including the A, B andC pillar trim and headliner)must be inspected and servicedby an authorized dealer. If the air curtain is not replaced, theunrepaired area will increase therisk of ...

The feature will continue to operate until the vehicle runs out of power. Disposal of airbags and airbag equipped vehicles(including pretensioners) Contact your authorized dealer as soon as possible. Airbags MUST BEdisposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following ...

Recommendations for Safety Restraints for Children Child size, height, weight, orage Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four oryounger) Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Smallch...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Attach the tether strap afterward, if included with the child seat. Referto Recommendations for attaching child safety restraints for children in this chapter. Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap whichextends from the back of ...

2. Locate the correct anchor for theselected seating position. 3. Open the tether anchor cover. 4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat te...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Changing tires with TPMS Each road tire is equipped witha tire pressure sensor locatedinside the tire/wheel cavity. Thepressure sensor is attached tothe valve stem. The pressuresensor is covered by the tire andis not visible unless the tire isremoved. Care must be takenwhen changing the tire to avoi...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires, Wheels and Loading 165 2010 Focus (foc) O...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

Front Wheel Drive (FWD) vehicles with manual transmissions: If your vehicle is equipped with a manual transmission, shifting thetransmission into neutral (N) permits “flat-towing” (all wheels on theground) for pulling behind a motorhome. Before you tow your vehicle: • Release the parking brake. • Mo...

STARTING Positions of the ignition 1. Off — locks the steering wheel,automatic transmission gearshiftlever and allows key removal. Thisposition also shuts the engine andall electrical accessories off. 2. Accessory—allows the electricalaccessories such as the radio tooperate while the engine is notru...

Starting the engine 1. Turn the key to 3 (on) withoutturning the key to 4 (start). 2. Turn the key to 4 (start), thenrelease the key as soon as theengine begins cranking. Your vehiclehas a computer assisted crankingsystem that assists in starting theengine. After releasing the key fromthe 4 (start) ...

Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an anti-lock braking system (ABS). Thissystem helps you maintain steering control during emergency stops bykeeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking ...

Parking brake To set the parking brake (1), pullthe parking brake handle up as faras possible. The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. WARNIN...

Switching Off Traction Control If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off the Traction Control feature of the AdvanceTrac 威 system may be beneficial because the wheels are allowed to spin. Thiswill restore full engine power and will enhance momentum th...

• Do not fill the power steering fluid reservoir above the MAX mark onthe reservoir. If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: • an improperly inflated tire • un...

1. Apply the parking brake, turnignition key to off, then remove thekey. 2. Using a screwdriver (or similartool), remove the protective coverto the interlock release access holeon the console. 3. Insert the screwdriver (or similartool) into the access hole and pressdownward while pulling thegearshif...

D (Drive) without Overdrive Overdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever. • This position allows for allforward gears (1–3) exceptoverdrive. • Provides engine braking. • Use when driving conditionscause excessive shifting from O/Dto other g...

If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears, stopping between shifts in asteady pattern. Press lightly on the accelerator in each gear. If necessary, try turning the Traction Control™ system of...

Recommended shift speeds Do not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch. Upshift according to the following chart: Recommended upshifts (for best fuel economy) when accelerating 5-speed manual transmission Shift from: 1 - 2 14 mph...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

Note: With extended use, the flasher may run down your battery. FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activat...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Protected circuits 40 20A Not used (spare) 41 15A Door lock/sunroof switchillumination, Auto dimming rearview mirror, Ambient lighting 42 10A Not used (spare) 43 10A Not used (spare) 44 10A Not used (spare) 45 5A Front wipers (logic) 46 7.5A Front passenger sensin...

CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Your vehicle may be equipped with a conventional spare tire that isdifferent in one or...

• Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar sparetire/wheel The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and...

Tire change procedure WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatictransmission) or R (Reverse) (manual transmission). WARNING: To help prevent the vehic...

3. If equipped with a 6-spoke wheelcover that’s bolted on, remove thefour plastic nuts by turningcounterclockwise 1/4 turn for accessto the lug nuts. Note: To avoid damage to the wheel cover, the 6-spoke wheel covercannot be removed until the tire isoff the vehicle. 4. Loosen each wheel lug nutone-h...

WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is onlymeant for changing the tire. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with t...

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fasteners thatattach the rotor to the hub are secured so they do ...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and aff...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, press and hold the clutch pedal, place thegearshift in N (Neutral), and release the clutch pedal. 2. Block the wheels. WARNING: T...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine oil filler cap 2. Brake/Clutch fluid reservoir 3. Power distribution box 4. Battery 5. Air filter 6. Automatic transmission fluid dipstick (if equipped) 7. Engine oil dipstick 8. Power steering fluid reservoir 9. Engine coolant reservoir 10....

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the eng...

Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material...

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle orbattery. Lift the battery with a battery carrier or with your hands onopposite corners. WARNING: Keep batteri...

When the battery is disconnected or a new battery installed, theautomatic transmission must relearn its adaptive strategy. As a result ofthis, the transmission may shift firmly when first driven. This operation isconsidered normal and will fully update transmission operation to itsoptimum shift feel...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interval s...

• Do not mix coolants. Add the coolant type originally equippedin your vehicle. Refer to Maintenance product specifications and capacities in this chapter. Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems.Th...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the COLD FILL RANGE or the FULL COLD level on the reservoir.If you removed the radiator cap in an ...

• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your ve...

When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase. Once the engine...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel conta...

WARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise,fuel may spray out and injure you or others. WARNING: If you do not use the proper fuel filler cap, ex...

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your authorized dealer toprevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hes...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

POWER STEERING FLUID Check the fluid. Refer to scheduled maintenance information. 1. Start the engine and let it rununtil it reaches normal operatingtemperature. 2. Turn the steering wheel left andright several times. 3. Turn the engine off. 4. Check the fluid level. 5. If the fluid is below the MIN...

High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/orpossible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels ...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. I...

6. Replace the air filter housing cover and secure the clamps. Be surethat the air cleaner cover tabs are engaged into the slots of the aircleaner housing. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage tothe e...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A AdvanceTrac ..............................179 Air cleaner filter ...............256–257 Air conditioning manual heating and airconditioning system .................42 Airbag supplemental restraintsystem ........................110, 119, 121 and child safety seats ............112description ..........