Focal FDP4.600V2 - User Manual
Focal FDP4.600V2 Car Amplifier – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL; The amplifier; LEVEL; control is adjusted to 8V.; SETTING LEVEL; Follow their gain overlap instructions.; NOT; FDP 4.600 V2 CONFIGURATION EXAMPLES; CHANNEL STEREO NON-BRIDGED
- Page 3 – IF YOU ARE USING TWO SUBWOOFERS; CHANNEL WITH BRIDGED SUBWOOFER; DO NOT use a 2 Ohm Subwoofer.
- Page 4 – BIAMP A WOOFER AND TWEETER; Connect the source deck front channel wires into inputs 3+4.
- Page 5 – CHANNEL BRIDGED; DO NOT USE a 2 ohm Speaker; adjustments, should be identical on both Channels.
- Page 6 – Remove the end panel by the power terminals
- Page 7 – TROUBLESHOOTING; > FOCAL SIGN DOES NOT LIGHT
- Page 8 – > SUBWOOFER REMOTE VOLUME CONTROL LED LIGHT; WARRANTY INFORMATION; from and authorized retailer; . This time period is extended to; no alterations; are; abuse, or modification; TECHNICAL SPECIFICATIONS
1
POWER PER CHANNEL
•
4 x 150 wRMS into 4 ohms @ 1% THD
•
4 x 200 wRMS into 2 ohms @ 1% THD
•
2 x 400 wRMS Bridged into 4 ohms @ 1% THD
DO NOT Bridge into 2 ohms
All power ratings are at 14.4v DC.
ROUTE SWITCH
•
1+2 = All four RCA inputs are used.
•
3+4 = Input signal on channels 3+4 are routed to channels 1+2. Use this mode when you need a band pass filter
on all four channels.
Recommended when bridging channels 1, 2, 3, 4.
The
LEVEL
controls still function.
•
Copy = Input signal and filters on channels 3+4 are copied to channels 1+2. Use this mode when you need a band
pass filter on all four channels.
Recommended when bridging channels 1,2,3,4.
The
LEVEL
controls still function.
CHANNELS 1 & 2 CROSSOVER CONFIGURATION
•
Flat: Full Range Signal. No crossover filter used.
•
HP: Activates the High Pass Filter for a midbass or tweeter.
CHANNELS 3 & 4 CROSSOVER CONFIGURATION
•
Flat: Full Range Signal. No crossover filter used.
•
HP: Activates the High Pass filter.
•
LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.
•
MONO Mode: Inputs 3+4 are mixed to mono for bridge mode operation. If 1+2 ROUTE is set to COPY then 1+2
will also be mono subwoofer and the remote volume control will control level.
The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control.
If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.
AUTOMATIC POWER TURN ON/OFF
1.
The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio
connected to the REM amplifier terminal.Band Pass for a subwoofer or midbass of a 3 way speaker.
2.
If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn
on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not
necessary.
FDP
4.600
V2
:
FOUR CHANNEL AMPLIFIER
OPERATION / CONFIGURATION MANUAL
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL • The amplifier LEVEL control has sufficient adjustment range for both low level and high level input into the RCA jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers, can be directly connected to ...
3 IF YOU ARE USING TWO SUBWOOFERS (SEE GRAPHIC B2) • Put your woofer/tweeters on channel 1+2. Set 1+2 switch to HP. Adjust 1+2 HP frequency to 70 Hz. • Subwoofers on channel 3+4. Set 3+4 switch to LP/BP. Set 3+4 switch to LP. Adjust 3+4 LP frequency to 70 Hz. Set the switch to MONO. Plug in the remo...
4 RADIO LP LP/BP 70Hz 3+4 70Hz HP MONO B3 (3 CHANNEL WITH BRIDGED SUBWOOFER) + – SUBWOOFER REMOTE SUB CONTROL XOVER XOVER BIAMP A WOOFER AND TWEETER (SEE GRAPHIC B4) • Connect the source deck front channel wires into inputs 3+4. • Set ROUTE switch to 3+4. • Set the switch to STEREO. • Connect your t...
