Page 2 - CHANNEL STEREO MODE
2 4 CHANNEL STEREO MODE INPUTS • Under the “INPUTS”, move the switch to either position of “2IN or 4IN” depending on how many inputs you are using to run the amp, 2 or 4. • If you are only using one single pair of RCA’s from your source, then plug them into the Channel 3+4 or (REAR) RCA inputs, and ...
Page 3 - Figure 2B | 4 Channel Stereo Mode Wiring Diagram
3 Select “ NORM ” Front Channel 1+2 Adjustments Select the amount of inputs you are using Rear Channel 3+4 Adjustments FRONT SPEAKERS + – + – REAR SPEAKERS + – + – BATTERY 50 AMP FUSE GROUND AMP TURN ON FDP SPORT LEFT Ch. 1 RIGHT Ch. 2 LEFT Ch. 3 RIGHT Ch. 4 Figure 2B | 4 Channel Stereo Mode Wiring ...
Page 4 - CHANNEL BRIDGED STEREO MODE; INPUTS; SLOPE; GAIN CONTROL; SPEAKER OUTPUTS
4 2 CHANNEL BRIDGED STEREO MODE INPUTS • You only need to use Rear INPUT Channels 3+4. NORMAL/BRIDGED • Set switch to “BRIDGED” SLOPE • Using the “SLOPE” switch on the top, select 12db for your crossover slope. CHANNELS 3 & 4 CROSSOVER CONFIGURATION • To adjust the crossovers, you will be lookin...
Page 5 - Figure 3B | 2 Channel Bridged Stereo Mode Wiring Diagram
5 LEFT RIGHT GROUND BATTERY 50 AMP FUSE AMP TURN ON Select “ BRIDGE ” 2 Channel Bridged Mode Adjustments Use Rear Inputs 3+4 Figure 3B | 2 Channel Bridged Stereo Mode Wiring Diagram FDP SPORT V2 FDP SPORT V2
Page 6 - CHANNEL STEREO & BRIDGED MONO MODE
6 3 CHANNEL STEREO & BRIDGED MONO MODE INPUTS • When using 1 set of RCA inputs to run the 3 channels, you only need to use INPUT Channels 3+4. Then switch the “2IN 4IN” switch to “2IN” • If using 2 sets of RCA inputs to run this configuration, you will switch the “2IN 4IN” switch to “4IN” NORMAL...
Page 7 - Figure 4B | 3 Channel Stereo & Bridged Mode Wiring Diagram
7 FRONT SPEAKERS + – + – SUBWOOFER + – + – GROUND AMP TURN ON BATTERY 50 AMP FUSE FDP SPORT LEFT Ch. 1 RIGHT Ch. 2 LEFT Ch. 3 RIGHT Ch. 4 Figure 4B | 3 Channel Stereo & Bridged Mode Wiring Diagram Select NORM Use these controls to adjust your Stereo HP Channels Select 2 IN Use these controls to ...
Page 8 - TROUBLESHOOTING; > FOCAL SIGN DOES NOT LIGHT
8 TROUBLESHOOTING > FOCAL SIGN DOES NOT LIGHT 1. Measure the voltage at the amplifier power terminal. It should be between 12 and 15 volts. 2. Measure the voltage at the amplifier REM terminal. It should be between 12 and 15 volts. 3. Is the REM wire connected? 4. Check your power and ground conn...
Page 9 - > FOCAL SIGN IS FLASHING
9 > FOCAL SIGN IS FLASHING 1. Is the amp very hot? Wait a few minutes for it to cool down. You need to get more fresh cool air to the amplifier. Do not cover the amplifier or mount it flush into a hole. 2. If the amp is cold and the Focal sign is flashing, there is an internal fault. 3. Start you...
Page 10 - WARRANTY INFORMATION; them to be free of manufacturing defects for a period of
10 WARRANTY INFORMATION Focal America / Orca Design & Manufacturing supports their products and guarantees them to be free of manufacturing defects for a period of 1 year (non-transferrable) from the date of purchase, if purchased from an authorized retailer . This time period is extended to 3 y...
Page 11 - TECHNICAL SPECIFICATIONS
11 TECHNICAL SPECIFICATIONS 4 x 150w RMS into 4 ohms @ 1% THD 4 x 200w RMS into 2 ohms @ 1% THD 2 x 400w RMS Bridged into 4 ohms @ 1% THD Do NOT bridge into 2 ohms. All power ratings are at 14.4v DC. Frequency Response: 20 – 30KHz + or -, 1dB Signal/Noise Ratio: 95dB (A) Input Voltage for rated outp...
