Page 2 - Accessing the System Wizard; Refer to page 12 for information; OR
C-1 Accessing the System Wizard Refer to page 12 for information on System Wizard Press MENU, select Settings and then System Wizard. OR
Page 3 - Insert the Batteries; Verify the Key; Quick Setup
C-2 Separate the key from the remote by inserting your thumbnail or a coin in the crease. Remove the key by grasping at the bottom. Insert the key face up and slide into place. Pull the remote battery cover off. Confirm your remote has the green number 1 key installed. Note: If you will be using the...
Page 4 - Making the Remote Work; Turn your ViP922 receiver
C-3 Quick Setup Confirm that your remote operates your receiver by pressing remote buttons. If this is not working, repeat step 5 . If the remote is still not linked to your ViP922 receiver, see page 10 in this guide. Making the Remote Work With Your Receiver 3 6 Turn your ViP922 receiver and TV on,...
Page 5 - Set Up the Remote to; step
C-4 Quick Setup Select TV Code and then follow the on-screen instructions to enter your TV’s device code. Set Up the Remote to Control Your TV 1 2 3 4 To set up the remote control to operate a TV, you can select a Device Code (see instructions on page 3). Your ViP922 DVR has a large database of Devi...
Page 6 - Quick Setup/Operation; Placing Your Remote; To take the remote out of Limited Mode, highlight
Quick Setup/Operation C-5 Placing Your Remote in Limited Mode Use the arrow button to highlight Enabled and then select it. 2 3 Highlight and select Save. 1 Select the Limited Mode option. To take the remote out of Limited Mode, highlight Disabled instead of Enabled in step 3 . Limited Mode locks ou...
Page 7 - Operation; Remote Operation
Receiver Power & TV Power Top button turns the receiver on/off, Bottom button turns the TV on/off Programming required (see C-4 ) Input Press once for Input Operation Remote Operation SAT Mode SAT Control TV volume Programming required (see C-4 ) Volume & Mute Buttons To use the features des...
Page 11 - Table of Contents
Table of Contents Quick Setup Verifying the Key ................................................................... C-2Inserting the Batteries ........................................................... C-2Linking Your Remote Control ................................................ C-3 Operation Set...
Page 13 - Note; : This remote control may support features not used by your; Great Idea; : Whenever you finish using
1 R EMOTE C ONTROL O VERVIEW Use this full-function remote control to operate the DISH Network ViP® 922 SlingLoaded™ DVR receiver. Also, you can program this remote control to operate most popular brands of audio/video equipment like a TV, a DVD/BD player (or VCR), or an audio receiver/amplifier. Se...
Page 14 - • POWER; VOLUME; • SELECT; MUTE; input so; OMBINATION
2 If you program the remote control to operate other equipment, refer to page C-6 and the following for remote-control operation instructions: • POWER , INPUT, MUTE , and VOLUME remote buttons are used to control your TV when it is programmed in TV mode. • The same buttons your DVR uses when in SAT ...
Page 15 - Instructions; MENU
3 (or TV/VCR), follow the instructions to program the remote to operate the TV using its code, and then repeat those instructions for the DVD/BD player or VCR in AUX mode using its code. Press the TV mode button to use the combination device’s TV functions, or the AUX mode button to use DVD/BD (or V...
Page 16 - Next; Entering Equipment Codes; Enter Model; POWER
4 5 Scroll the Sort By: (or Aux Device: ) list to position the option you wish to select within the blue highlight bar. Then highlight your device’s name in the Brand: list and select Next . If the brand is not listed, see Entering Equipment Codes on page 5. If there is no equipment code for your de...
Page 17 - Yes; OPTIONAL—For setting
5 E NTERING E QUIPMENT C ODES 10 If the code worked for other buttons, select Yes and continue with step 11. If the code did not work, select No and repeat steps 6 through 9 for the next code for your brand. Choose the code that provides the remote with support for the most device functions. If you ...
Page 20 - Control Audio Amplifier Volume
8 S WITCHING B ETWEEN TV AND A MPLIFIER V OLUME C ONTROL If a remote control used with the ViP922 DVR has been set up to operate a TV, then MUTE and VOLUME +/- buttons adjust the TV’s volume. To use the remote to adjust the volume of your remote-controllable audio equipment instead of adjusting your...
Page 21 - RF I; NTERFERENCE; DJUSTING; AUX
9 V IEWING E QUIPMENT C ODES These instructions explain how to read out and verify the device code(s) for the equipment you have programmed the remote to control. You may write these code(s) in the spaces provided in the table on the last page, just in case you need to enter a device code manually. ...
Page 22 - DVR B; UTTONS; SKIP BACK
10 1 Make sure the UHF-2G remote antenna is connected to the correct input on the receiver’s back panel and is not touching anything else. It should be tightened only by hand. Note : Remote antennas used with other DISH Network satellite receivers and remotes cannot be used with your ViP922 receiver...
Page 23 - twice on another linked; Locate
11 C OLORED B UTTONS The following table lists some of these shortcuts for the colored set of buttons on your ViP922 DVR remote control. Note that scheduled updates to your receiver software may add to or modify these shortcuts. L OCATING A L OST R EMOTE The next time you misplace a remote control o...
Page 24 - Settings; tile and then; System Wizard
12 To access the System Wizard from your ViP922 DVR front panel: 1 With your receiver turned on, touch the front panel to activate it, and then select MENU . 2 Use the arrow controls to highlight the Settings tile and then SELECT it. 3 Use the arrow controls to scroll down the list of Settings items...
Page 25 - ROUBLESHOOTING
13 T ROUBLESHOOTING What’s Happening What’s Wrong What You Can Do The remote control or one or more buttons on it seems to have stopped working. The remote control has gone to “sleep” to reduce battery drain. Wake the remote control by pressing one or more button(s) on the remote, such as the SELECT...
Page 27 - DISH N; ETWORK
15 L IMITED W ARRANTY This warranty extends only to the original user (“you,” “your”) of the DISH Network remote control and is limited to the purchase price of the remote control. EchoStar Technologies L.L.C., formerly known as EchoStar Technologies Corporation, and its affiliated companies (“we,” ...
Page 28 - CCESSORY
16 Advance Exchange Program The Advanced Exchange Program allows you to have a replacement remote shipped immediately to you. Depending upon where you live, the remote should arrive within 3 to 5 business days. You will not have to return your defective remote to DISH Network using this program.A sh...
Page 30 - Printed in
18 R EGULATORY F ACTORS This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Change...
Page 31 - To read out your remote codes, see page 9 for instructions.; then only Volume and Mute buttons work in TV mode.
To read out your remote codes, see page 9 for instructions. If your remote is in Limited Mode (see page C-6), then only Volume and Mute buttons work in TV mode. Remote Key Auxiliary Equipment Code 1
