Dish Network 11 - Manual - manualsarea.com

Page 2 - Install Your Selected; Quick Setup

A B Separate the key from the remote by inserting your thumbnail or coin in the crease. Remove key by grasping at the bottom. Insert face up the key you selected on the previous page. Pull the remote battery cover off. the remote battery cover. Insert 4 AAA batteries making sure to match the plus (+...

Page 3 - Making the Remote Work; If you installed one of these

1 UHF PRO SYSTEM INFO RECORD Turn your receiver and INFO on the front of the receiver. Information screen. Press RECORD on your remote. The remote address will probably change on the screen. Confirm that your remote operates your receiver by pressing remote buttons. If your remote has a blue number ...

Page 4 - TV; Program the Remote to

# TV POWER TV Turn your TV on. Press & hold the TV Mode button until all Mode buttons light up. Press POWER. Press the UP ARROW repeatedly until your TV turns off (about 1 press per second) . Press POUND. Press the POWER button to turn the TV on and try other buttons to make sure the code works....

Page 5 - For TV2 Remote Controls on; Programming your Recover button allows

Programming the Recover Button for TV2 Operation For TV2 Remote Controls on 942, 625, & 522 Receivers Press STAR. # Press POUND. 1 2 TV Press & hold the TV Mode button until all Mode buttons light up. Enter the channel number you tune your TV to when you watch satellite programming. 4 3 C-5 ...

Page 6 - Placing Your Remote; Press; TV Mode button; Quick Setup/Operation

SELECT the mode lights stop flashing. If yousee the System Information screen,go to step 4. If not, repeat this stepuntil you do. 5 1 2 System Info Mon, October 18 Model ID DISH Player-DVR 942R00000000000-00S00000000000-00DNASP000 Rev000ABCDEFGH-I0000ABCD1-800-333-DISH (3474)1-800-333-DISH (3474)htt...

Page 8 - Remote Operation; TV Mode; button; Operation; Press this

R DVR SELECT POWER TV VCR AUX TV TV/VIDEO VOLUME PAGE MUTE GUIDE RECALL CANCEL INFO SKIP BACK BACK SKIP FWD FWD PAUSE STOP PLAY RECORD abc def T H E M E S B R O W S E P O S I T I O N D IS H O n Dema nd Remote Key may be different than shown here SAT C-8 Remote Operation TV Mode TV Power TV Menu Up/D...

Page 9 - VCR Mode; Top button

R DVR SELECT POWER TV VCR AUX TV TV/VIDEO VOLUME PAGE MUTE GUIDE RECALL CANCEL INFO SKIP BACK BACK SKIP FWD FWD PAUSE STOP PLAY RECORD PIP abc def T H E M E S B R O W S E P A W S P O S I T I O N D IS H O n Dema nd Remote Key may be different than shown here SAT C-9 Remote Operation VCR Mode VCR/DVD ...

Page 10 - Table of Contents; Switching Between TV and Amplifier

Table of Contents COLOR PAGES... IN THIS GUIDE... Quick Setup Confirm Your Receiver Model and Select the Right Key ..Install Your Selected Key .....................................................Insert the Batteries ...............................................................Making the Remote Wo...

Page 11 - Programming for Other Equipment; Note; : This remote control may have features not used by your; Great Idea; : Whenever you finish using

1 R EMOTE C ONTROL O VERVIEW Use this full-function remote to control a variety of DISH Network receivers, such as Standard Definition, High Definition, and Digital Video Recorder receivers. Also, you can program the remote to control most of the popular brands of audio/video equipment like a TV, VC...

Page 12 - OMBINATION

2 If you program the remote to control equipment in AUX mode, refer to the following for remote control operation instructions: • TVs, page C-7. • VCRs and DVD players, page C-8. • DISH Network satellite receivers, page C-9. • Stereo equipment use only these buttons: SELECT (change inputs), MUTE , V...

Page 13 - Programming Using the Equipment Code Tables; Scanning for Equipment Codes

3 L IMITED M ODE You can program your remote control in Limited Mode to keep from accidentally changing the channel on your TV or VCR. When you use the remote to control your TV in Limited Mode, you will only be able to use the POWER , MUTE , and VOLUME buttons to control your TV. Also, when you use...

Page 14 - Limited Mode; Instructions

4 S CANNING FOR E QUIPMENT C ODES 6 If you want to program Limited Mode, press 1. If not, skip to step 7. See Limited Mode on page 3 for more information. 7 Press POUND (#). If you entered the code correctly, the mode button flashes three times. 8 Press POWER to turn off the equipment. If the equip-...

Page 16 - Control Amplifier Volume

6 S WITCHING B ETWEEN TV AND A MPLIFIER V OLUME C ONTROL When you set up the remote to control a TV, the MUTE and VOLUME buttons control the TV volume, even if your remote control is in SAT mode. However, if you want to use the AUX mode to control a tuner or amplifier that has a volume setting, you ...

Page 18 - System; twice

8 A VOIDING R EMOTE C ONFLICTS Because your remote control uses UHF, you may experience interference from other nearby remotes. The instructions in this section describe how to avoid remote conflicts. C HANGING THE R EMOTE AND R ECEIVER A DDRESS One quick way to avoid remote conflicts is by changing...

Page 19 - Remote Address; UHF F; System Information; Battery

9 3. Use the NUMBER PAD to enter any number between 1 and 16, but not the one you wrote in step 1. 4. Press POUND (# ). If you entered the address correctly, SAT will flash three times. Write down the number you entered in Your Remote Control Codes on page 24. 5. Press RECORD . Make sure the Remote ...

Page 21 - TV Out

11 6. Move the highlight to the address for the Remote Address as shown below. This is important - if you do not move the highlight, your remote will change the receiver's Remote Address and cause your Remote Control 1 to control the TV2 side of your receiver. 7. Press the RECORD button on the green...

Page 22 - TV C; ODES; Programming in AUX mode; : In most cases use these codes to

12 E QUIPMENT C ODES These tables contain the manufacturer codes for programming the remote to control your TV, a VCR, DVD player, or audio amplifier. Every attempt has been made to include all codes. If your equipment brand is not listed or if the codes do not work, the remote may not control your ...

Page 24 - VCR C

14 TV C ODES (C ONTINUED ) Technics 508 673 676 Techwood 523 573 652 654 660 676 Teknika 504 505 512 516 523 524 525 526 534 536 541 573 644 652 653 654 655 657 658 661 662 664 665 666 670 672 675 680 682 685 726 727 Telefunken 679 Toshiba 516 590 617 631 635 667 680 683 688 750 771 Totevision 526 6...

Page 26 - DVD P; LAYER

16 T UNER /A MPLIFIER C ODES Programming in AUX mode : Press 2 before entering the tuner/ amplifier code. Aiwa 636 641 656 687 718 720 724 725 726 Bose 761 Carver 653 Citizen 709 Curtis Mathes 734 Denon 647 674 757 758 759 760 762 Fisher 653 741 GE 711 Goldstar 677 690 Harmon/Kardon 640 672 751 Hita...

Page 28 - ROUBLESHOOTING

18 T ROUBLESHOOTING What’s Happening What’s Wrong What You Can Do While doing remote control procedure, the remote control stops working. • If you don’t press any button for 20 seconds in a programming sequence, the remote shuts off its programming function. Start over again. You cannot find the key...

Page 30 - DVANCE

20 L IMITED W ARRANTY This warranty extends only to the original user (“you,” “your”) of the DISH Network remote control and is limited to the purchase price of the remote control. EchoStar Technologies Corporation and its affiliated companies (“we,” “our,” “us”) warrant this remote control against ...

Page 33 - Reference Tables; To read out your remote codes, see page 10 for instructions.

Write down your remote address, channel numbers/inputs, TV, VCR, DVD player, and stereo equipment codes as you program them for future reference. Reference Tables TV VCR AUX Remote Address Channel or Input for Satellite Programming Channel for Satellite Programming on TV2 (942 receivers only) TV Cod...

Dish Network 11 - Manual

Table of Contents:

Summary

Other Dish Network Models