Dish Network 104333 - Manual

VCR (VideoCassette Recorder) Mode 10 104333 U P /D OWN (A RROW ) B UTTONS Use the Up/Down arrow buttons to change channels on the TV. R ECALL B UTTON Press this button to return to the last channel you were watching. Press it again to switch between the last two channels that you watched. N UMBER B ...

AUX (Auxiliary) Mode for Cable TV Box 12 104333 N UMBER B UTTONS Use these buttons to enter numbers in a menu. AUX (A UXILIARY ) M ODE FOR C ABLE TV B OX AUX M ODE B UTTON To use the remote to operate a cable TV box, you must first set up the remote to control the cable box. See Controlling a Device...

AUX (Auxiliary) Mode for Tuner or Amplifier 104333 13 S ELECT B UTTON The Select button works as the Enter button for the cable box. U P /D OWN (A RROW ) B UTTONS Use the Up/Down arrow buttons to change channels on the cable box. R ECALL B UTTON Press this button to return to the last channel you we...

Controlling a Device 104333 15 R EMOTE C ONTROL P ROCEDURES C ONTROLLING A D EVICE This section explains how to set up the remote to control a device, such as a satellite TV receiver, a TV, a VCR, a cable TV box, a tuner, or an amplifier. Note: The remote already is set up to control the receiver. B...

Changing the Remote Control Address 16 104333 C HANGING THE R EMOTE C ONTROL A DDRESS Note: Do not change the address of the remote unless absolutely necessary , because the remote cannot control the receiver if the two devices have different addresses. If you start doing this procedure and then do ...

Installing an Attenuator 104333 17 I NSTALLING AN A TTENUATOR Unwanted UHF signals may block signals from the remote control to the receiver. To prevent such blockage, you can install a 10 dB attenuator. This will help keep out other UHF signals, but also reduce the distance at which you can use the...

Controlling Sound Volume 18 104333 C ONTROLLING S OUND V OLUME R ECEIVER V OLUME C ONTROL The receiver may have its own volume control. When you first install such a receiver, it is set up so that the remote cannot control the receiver sound volume. You can set up the receiver so that the remote can...

Controlling Sound Volume 104333 19 TV OR A MPLIFIER V OLUME C ONTROL If you set up the remote to control a television, the Mute and Volume buttons - in any mode - control the TV volume. This applies whether or not the receiver has its own volume control. This does not apply if you use the AUX mode t...

Doing the Device Code Scan 20 104333 D OING THE D EVICE C ODE S CAN If a device is not listed in the tables or if the listed codes do not work, you can scan through all the codes, testing each one. Remember that the remote may not control some devices. 1. Press and hold the mode button for the devic...

Finding the Device Codes 104333 21 F INDING THE D EVICE C ODES You can find out what device code is set for each remote control mode. Do the following: 1. Press and hold the mode button for the device, for about three seconds. When all the other mode button backlights come on, release the mode butto...

22 104333 D EVICE C ODES Use these codes to set up the remote to control other devices. If a device is not listed or the codes do not work, the remote may not be able to control the device. Note: The end of the VCR table provides codes for DVD players. Only for a receiver that has its own volume con...

104333 25 T UNERS /A MPLIFIERS D VD Players N ote: You must set the remote control to VC R m ode to set i t up to control a DVD player. You m ust set the remote control to VCR mode to use it to control a DVD player. Magnavox 626 P ioneer 619 R CA 627 S ony 617 Toshiba 616 A iwa 2656, 2680 C arver 26...