Page 3 - Table of Contents; SETUP AND OPERATION; Quick Setup; IN THIS GUIDE
Table of Contents SETUP AND OPERATION Quick Setup Insert the Batteries ..............................................................S-1Making the Remote Work with Your Receiver ...................S-1Program the Remote to Control Your TV ...........................S-2Placing Your Remote in Limited M...
Page 4 - Insert the Batteries; Making the Remote Work
Insert the Batteries 1 2 S-1 Replace the remote battery cover. A B Batter y Batter y Insert 4 AAA batteries making sure to match the plus (+) ends with the plus markings on the battery case. 3 A B Batter y Batter y Quick Setup A B Pull the remote battery cover off. 1 RECORD Turn your receiver and TV...
Page 5 - Program the Remote to
S-2 Quick Setup Turn your TV on. Press & hold the TV Mode button until all Mode buttons light up. Press POWER. Press the UP ARROW repeatedly (about 1 press per second) until your TV turns off. Press POUND. Press the POWER button to turn the TV on and try other buttons to make sure the code works...
Page 6 - Quick Setup/Operation; Placing Your Remote; If You Lose Your Picture; Press
S-3 Quick Setup/Operation SELECT Press and hold RECOVER until all mode buttons light up. If you see the System Info screen, proceed to step 4. Otherwise, continue to step 3. Press RECOVER again & wait until the mode lights stop flashing. If you see the System Info screen, go to step 4. If not, r...
Page 7 - Operation; Remote Operation
S-4 Operation Remote Operation SAT Mode SAT To use the features described in this section, make sure you are in SAT mode by pressing the SAT Mode button. Note: Some features may not be available depending on your receiver model. Receiver Power & TV Power Receiver Menu Program Guide Arrows/Select...
Page 11 - Note; : This remote control may have features not used by your; Great Idea; : Whenever you finish using
1 R EMOTE C ONTROL O VERVIEW Use this full-function remote to control your DISH Network receiver. Also, you can program the remote to control most of the popular brands of audio/video equipment like a TV, VCR, DVD player, or a second DISH Network satellite receiver. See Programming for Other Equipme...
Page 13 - Programming Using the Equipment Code; IXED
3 L IMITED M ODE You can program your remote control in Limited Mode to keep from accidentally changing the channel on your TV or VCR. When Limited Mode is enabled, you cannot select TV mode. If you press the TV button while TV mode is programmed in Limited Mode, the TV button flashes and the SAT bu...
Page 14 - Instructions; Scanning for Equipment Codes
4 P ROGRAMMING U SING E QUIPMENT C ODE T ABLES You can set up the remote to control other equipment using the equipment codes listed on page 12 and the modes as shown on page 1. Instructions Additional Information 1 Turn the equipment on. Use the equipment’s front panel buttons or its remote control...
Page 15 - Scanning for; For
5 S CANNING FOR E QUIPMENT C ODES 9 Turn the equipment back on and try some other buttons to make sure they work. If the code works for other buttons, stop here. Note : If you have programmed your remote in Limited Mode, only the MUTE and VOLUME buttons work. For example, sometimes POWER works when ...
Page 16 - Placing Your
6 4 Press POWER . This puts your remote in the scan mode. 5 Press the UP or DOWN ARROW repeatedly until the equipment turns off. As you press the UP or DOWN ARROW , the remote tries each code in the memory to see if it can turn off your equipment. When the equipment turns off, you have found a code ...
Page 17 - Control Amplifier Volume
7 S WITCHING B ETWEEN TV AND A MPLIFIER V OLUME C ONTROL When you set up the remote to control a TV, the MUTE and VOLUME buttons control the TV volume, even if your remote control is in SAT mode. However, if you want to use the AUX mode to control a tuner or amplifier that has a volume setting, you ...
Page 18 - AUX M; User Guide
8 P ROGRAMMING THE R EMOTE TO C ONTROL A S ECOND R ECEIVER IN AUX M ODE If you have another DISH Network satellite receiver installed, you can use this remote in AUX mode to control it along with your new receiver. When you program the remote to control the other receiver, the remote sends out IR si...
Page 19 - twice
9 R EADING O UT THE R EMOTE C ONTROL C ODES These instructions explain how to check the codes you put in the remote control when you set it up. Be sure to write them in the spaces provided on the inside of the back cover. Instructions Additional Information 1 Press and hold the mode button for the e...
Page 20 - Changing the Remote and Receiver Address; Remote Address
10 D ISCRETE C ODES FOR L EARNING R EMOTES Remote control discrete On and Off IR commands are used by installers when programming macro commands into universal remotes. Using an On-only or Off-only command is more effective than a toggle On/Off command when trying to ensure the satellite receiver is...
Page 21 - you see on
11 5 Press RECORD . Make sure the Remote Address you see on the System Info screen is the same as the one you entered in step 3. If it isn’t, the remote cannot control the receiver. Press RECORD a second time. 6 Press SELECT to close the System Info screen.
Page 22 - TV C; ODES; Programming in AUX mode; : In most cases use these codes to
12 E QUIPMENT C ODES These tables contain the manufacturer codes for programming the remote to control your TV, a VCR, DVD player, or audio amplifier. Every attempt has been made to include all codes. If your equipment brand is not listed or if the codes do not work, the remote may not control your ...
Page 24 - VCR C
14 TV C ODES (C ONTINUED ) Scott 526 534 541 600 652 654 655 657 662 682 696 701 Sears 523 534 542 563 590 595 601 604 617 627 631 635 645 646 650 652 654 656 682 683 688 691 703 725 726 Seimitsu 627 Sharp 521 526 585 605 607 628 629 652 654 655 658 739 740 741 777 794 803 835 836 898 913 Shogun 652...
Page 27 - Programming for combination equipment; : Program the remote
17 JVC 637 703 725 786 827 Kenwood 676 691 726 728 774 795 828 829 830 831 832 840 842 Magnavox 654 705 Marantz 651 764 845 Nakamichi 671 NEC 716 Onkyo 642 660 662 678 785 788 790 791 792 796 801 846 Optimus 648 664 Panasonic 643 644 652 783 797 798 799 808 810 815 816 817 818 819 820 821 822 824 82...
Page 28 - Table continues on next page
18 TV/VCR/DVD C OMBO C ODES Programming for combination equipment : Program the remote control in TV mode using the TV code, then in VCR mode using the VCR code, and then DVD in AUX mode (press 1 before entering the DVD code) using the DVD code. TV/DVD C OMBO C ODES Programming for combination equip...
Page 30 - ROUBLESHOOTING
20 T ROUBLESHOOTING What’s Happening What’s Wrong What You Can Do While doing remote control procedure, the remote control stops working. • If you don’t press a button for 20 seconds in a programming sequence, the remote shuts off its programming function. Start over again. When you press a button o...
Page 33 - DISH N; ETWORK; Advance Exchange Program; CCESSORY; OU
23 DISH N ETWORK ’ S E XCHANGE P ROGRAMS DISH Network offers two options if you need to replace your remote control: the Advanced Exchange Program and the Post Receipt Exchange Program. Advance Exchange Program The Advanced Exchange Program allows you to have a replacement remote shipped immediately...
Page 34 - UBLISHING
24 d. We will: • Check the remote control, including whether it is covered under the warranty. • Replace any remote we find is defective with a new or refurbished remote, if the defective remote is covered under the warranty. We will ship the replacement remote at our expense. • If a defective remot...
Page 39 - To read out your remote codes, see page 9 for instructions.
To read out your remote codes, see page 9 for instructions. If you enter a “1” as the last number of your code, your remote is in Limited Mode (see page 3 for more details).
