Dewalt DCS371P1 - User Manual

Page 3 - English; ) POWER TOOL USE AND CARE; Keep cutting tools sharp and clean.; ) BATTERY TOOL USE AND CARE; Recharge only with the charger specifi

2 English tool while you are tired or under the inﬂ uence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non- skid sa...

Page 6 - WARNING: Fire hazard. Do not store or carry the battery pack; The RBRCTM Seal; WALT and other battery users, has

5 English WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery pack case is cracked or damaged, do not insert into the charger. Do not crush, drop or damage the battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run...

Page 7 - DO NOT attempt to charge the battery pack with any

6 English WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock may result. CAUTION: Burn hazard. To reduce the risk of injury, charge only D E WALT rechargeable battery packs. Other types of batteries may overheat and burst resulting in personal injury and propert...

Page 8 - NEVER; Chargers; Your tool uses a D; Indicator Light Operation; PACK CHARGING; Charge Indicators

7 English • Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorized service center. • Do not disassemble the charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result...

Page 9 - LEAVING THE BATTERY PACK IN THE CHARGER; Important Charging Notes; Shock hazard. Don’t allow any liquid to get inside the; Storage Recommendations

8 English LEAVING THE BATTERY PACK IN THE CHARGER The charger and battery pack can be left connected with the charge indicator showing Pack Charged. WEAK BATTERY PACKS: Weak batteries will continue to function but should not be expected to perform as much work. FAULTY BATTERY PACKS: This charger wil...

Page 10 - Releasing the trigger switch also automatically; Blades; DO NOT; Blade Selection; Blade Description; SAVE THESE INSTRUCTIONS; INTENDED USE

9 English the motor OFF. Releasing the trigger switch also automatically actuates lock-off button. WARNING: This tool has no provision to lock the switch in the ON position, and should never be locked ON by any other means. LED Worklight (Fig. 2) There is a worklight (S) located above the blade The ...

Page 11 - Never use the band saw to cut resin materials; BLADE DESCRIPTION; WARNING: To reduce the risk of serious personal; TO ADJUST THE BLADE TRACKING; Turn and open the blade tension lever (I) to allow access

10 English The following table is intended as a general guide only. Determine the type of material and dimension of the workpiece and select the most appropriate band saw blade. NOTICE: Never use the band saw to cut resin materials which are subject to melting. Melting of resin material caused by hi...

Page 12 - Turning the tracking screw clockwise

11 English 3. Use a 3 mm hex wrench (E) to turn one of the tracking screws (O) 1/4 turn clockwise. Turn the other tracking screw 1/4 turn clockwise. NOTE: Turning the tracking screw clockwise moves the blade toward the guide roller, turning the tracking screw counterclockwise moves the blade away fr...

Page 13 - WARNING: To reduce the risk of serious personal injury,

12 English FUEL GAUGE BATTERY PACKS (FIG. 2) Some D E WALT battery packs include a fuel gauge which consists of three green LED lights that indicate the level of charge remaining in the battery pack. To actuate the fuel gauge, press and hold the fuel gauge button (R). A combination of the three gree...

Page 14 - NOTE; It is available at extra cost from your local dealer or authorized

13 English FIG 6 FIG. 7 F Installing the Brush, Brush Cap and Blade Guards (Fig. 8) WARNING: To reduce the risk of serious personal injury, turn tool off and remove the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause inju...

Page 15 - Cutting

14 English OPERATION WARNING: To reduce the risk of serious personal injury, turn tool off and remove the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. Cutting Refer to Figure 10 for recommended cutting position...

Page 16 - WARNING: To reduce the risk of serious personal injury, the; Tips for Better Cutting; coolants will cause build-up on tires and reduce performance.; MAINTENANCE; Lubrication; RECOMMENDED CUTTING POSITIONS

15 English 7. Whenever possible, hold the saw ﬁ rmly in both hands. If the optional blade guards (Fig. 8) are installed, the saw can be operated with one hand. Keep your free hand clear of the blade area and do not allow the saw to fall against the clamped or supported material or your body when the...

Page 17 - CHARGER CLEANING INSTRUCTIONS; Accessories; CONFIRMATION OF OWNERSHIP:; Three Year Limited Warranty; YEAR FREE SERVICE

16 English Cleaning WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic p...

Page 18 - WALT is not responsible for any injury caused by tampering and

17 English 2 YEARS FREE SERVICE ON D E WALT BATTERY PACKS DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120, DCB127, DCB201, DCB203 and DCB207. 3 YEARS FREE SERVICE ON D E WALT BATTERY PACKS DCB200, DCB204, DCB205 D E WALT BATTERY PACKS Product warranty voided if the battery pack is tampered wi...