Dewalt DCS551 - Manual

Defi nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.

DANGER:

Indicates an imminently hazardous situation which, if not avoided,

will

result in

death or serious injury

.

WARNING:

Indicates a potentially hazardous situation which, if not avoided,

could

result in

death or serious injury

.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided,

may

result

in

minor or moderate injury

.

NOTICE:

Indicates a practice

not related to personal injury

which, if not avoided,

may

result in

property damage

.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

E

WALT TOOL, CALL US

TOLL FREE AT:

1-800-4-D

E

WALT (1-800-433-9258)

.

WARNING:

To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.

1) WORK AREA SAFETY

a)

Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b)

Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or

fumes.

c)

Keep children and bystanders away while operating a power tool.

Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a)

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching

outlets will reduce risk of electric shock.

b)

Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed

or grounded.

c)

Do not expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

d)

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or

entangled cords increase the risk of electric shock.

e)

When operating a power tool outdoors, use an extension cord suitable for outdoor
use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f)

If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply.

Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a)

Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication.

A moment of inattention while operating power tools may

result in serious personal injury.

b)

Use personal protective equipment. Always wear eye protection.

Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.

c)

Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the
switch on invites accidents.

d)

Remove any adjusting key or wrench before turning the power tool on.

A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

e)

Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

f)

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts.

Loose clothes, jewelry or long hair can be caught in moving

parts.

g)

If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a)

Do not force the power tool. Use the correct power tool for your application.

The

correct power tool will do the job better and safer at the rate for which it was designed.

b)

Do not use the power tool if the switch does not turn it on and off.

Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c)

Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d)

Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool.

Power tools are

dangerous in the hands of untrained users.

e)

Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use.

Many accidents are caused by poorly

maintained power tools.

f)

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g)

Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed.

Use of the power tool for operations different from those intended could result in

a hazardous situation.

5) BATTERY TOOL USE AND CARE

a)

Recharge only with the charger specified by the manufacturer.

A charger that is suitable

for one type of battery pack may create a risk of fire when used with another battery pack.

b)

Use power tools only with specifically designated battery packs.

Use of any other

battery packs may create a risk of injury and fire.

c)

When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws, or other small metal objects, that can make a
connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d)

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help.

Liquid ejected from the battery may cause irritation or burns.

INSTRUCTION MANUAL

GUIDE D’UTILISA

TION

MANUAL DE INSTRUCCIONES

DCS551

20V Max* Cut Out T

ool

Outil à découper 20 

V max*

Recortadora de 20 V Máx*

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SER

VICIO Y

PÓLIZA DE GARANTÍA.

ADVER

TENCIA:

LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

D

E

WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

(MAR14) Part No. N382917 DCS551 Copyright © 2014 D

E

WALT

The following are trademarks for one or more D

E

WALT power tools: the yellow and black color scheme, the “D” shaped

air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on
the surface of the tool.

6) SERVICE

a)

Have your power tool serviced by a qualified repair person using only identical
replacement parts.

This will ensure that the safety of the power tool is maintained.

Additional Specifi c Safety Rules for Cut-Out Tools

• Use clamps or another practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body leaves it unstable and may lead to loss

of control.

• Hold power tools by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring.

Contact with a "live" wire will make exposed

metal parts of the tool "live" and shock the operator.

WARNING:

After changing bits or making any adjustments, make sure the collet nut is securely

tightened to avoid injury.

WARNING:

Do not press spindle lock or collet lock buttons while motor is running. The operator

may lose control and drop the tool. Personal injury or serious tool damage may result.

WARNING:

Shut off all live electric circuits to any areas where cut outs will be made, to avoid fire

or serious personal injury.

CAUTION:

Do not touch the bit or collet nut during or immediately after cutting material. The bit

and collet nut may be hot enough to burn bare skin.
•

Do not run tool while carrying at your side.

The spinning bit may become entangled with

clothing and injury may occur.

•

Always wear eye protection.

Dust mask and hearing protection must be used for appropriate

conditions. Using personal safety devices is recommended. WORK SAFE.

•

Always operate the tool with the depth guide in place.

The guide keeps the bit from plunging

too deeply through the material. A minimum of penetration should be maintained to eliminate the
danger of cutting into electric wiring.

•

Do not use this tool with drill or screwdriver bits.

This tool is not intended to be used as a

drill or screwdriver.

•

Be sure your cutting bits are sharp and in good condition.

Damaged bits can cause the tool

to jump, injuring the operator.

•

Never touch the bit immediately after use.

It may be extremely hot.

•

Always follow the bit manufacturer’s speed recommendations as some bit designs
require specific speeds for safety or performance.

If you are unsure of the proper speed or

are experiencing any type of problem, contact the bit manufacturer.

•

Be sure that the motor has stopped completely before you lay the tool down.

If the cutter

head is still spinning when the tool is layed down, it could cause injury or damage.

•

Be sure that the bit is clear of the workpiece before starting motor.

If the bit is in contact

with the workpiece when the motor starts it could make the tool jump, causing damage or injury.

•

If your tool fails to function properly, take it to an authorized service center.

There are no

user serviceable parts inside this tool and it should only be opened by trained service personnel.

•

Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long

hair can be caught in moving parts.

WARNING: ALWAYS

use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,
•

crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water.

Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING:

Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use.

Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the

battery pack but may be easily knocked over.
• The label on your tool may include the following symbols. The symbols and their definitions are as

follows:

V ...................... volts A

......................... amperes

Hz .................... hertz

W ........................ watts

min .................. minutes

or AC ............. alternating current

or DC ..... direct current

or AC/DC ...... alternating or direct current

.................... Class I Construction

no ........................ no load speed

........................

........................ (grounded)

n .......................... rated speed

................... Class II Construction

........................ earthing terminal

........................

(double insulated)

........................ safety alert symbol

…/min ............. per minute

BPM .................... beats per minute

IPM .................. impacts per minute

RPM .................... revolutions per minute

SPM ................ strokes per minute

sfpm .................... surface feet per minute

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include the catalog number and voltage.
Consult the chart at the end of this manual for compatibility of chargers and battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack and
charger, read the safety instructions below and then follow charging procedures outlined.

READ ALL INSTRUCTIONS

•

Do not charge or use the battery pack in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust.

Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT modify the battery pack in

any way to fit into a non-compatible charger as battery pack may rupture causing
serious personal injury.

Consult the chart at the end of this manual for compatibility of

batteries and chargers.

• Charge the battery packs only in designated D

E

WALT chargers.

•

DO NOT

splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature

may reach or exceed 105  °F (40  °C) (such as outside sheds or metal buildings in
summer).

For best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the trigger switch locked on.
Never tape the trigger switch in the ON position.

WARNING:

Fire hazard. Never attempt to open the battery pack for any reason. If the battery

pack case is cracked or damaged, do not insert into the charger. Do not crush, drop or damage
the battery pack. Do not use a battery pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped
on). Damaged battery packs should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects

can contact exposed battery terminals.

For example, do not place the battery pack in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently
come in contact with conductive materials such as keys, coins, hand tools and the
like.

The US Department of Transportation Hazardous Material Regulations (HMR) actually

prohibit transporting batteries in commerce or on airplanes (e.g., packed in suitcases and carry-
on luggage) UNLESS they are properly protected from short circuits. So when transporting
individual battery packs, make sure that the battery terminals are protected and well insulated
from materials that could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

•

Do not incinerate the battery pack even if it is severely damaged or is completely
worn out.

The battery pack can explode in a fire. Toxic fumes and materials are created

when lithium ion battery packs are burned.

•

If battery contents come into contact with the skin, immediately wash area with
mild soap and water.

If battery liquid gets into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is
composed of a mixture of liquid organic carbonates and lithium salts.

•

Contents of opened battery cells may cause respiratory irritation.

Provide fresh air. If

symptoms persist, seek medical attention.

WARNING:

Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corp

oration) Seal on the nickel

cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate
that the costs to recycle these batteries (or battery packs) at the end of their useful
life have already been paid by D

E

WALT. In some areas, it is illegal to place spent

nickel cadmium, nickel metal hydride or lithium ion batteries in the trash or
municipal solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC™, in cooperation with D

E

WALT and other battery users, has established programs in

the United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal
hydride or lithium ion batteries. Help protect our environment and conserve natural resources by
returning the spent nickel cadmium, nickel metal hydride or lithium ion batteries to an authorized
D

E

WALT service center or to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the

Rechargeable Battery Recycling Corporation.

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS:

This manual contains important safety and operating

instructions for battery chargers.
• Before using the charger, read all instructions and cautionary markings on the charger,

battery pack and product using the battery pack.

WARNING:

Shock hazard. Do not allow any liquid to get inside the charger. Electric shock

may result.

CAUTION:

Burn hazard. To reduce the risk of injury, charge only D

E

WALT rechargeable

battery packs. Other types of batteries may overheat and burst resulting in personal injury and
property damage.

NOTICE:

Under certain conditions, with the charger plugged into the power supply, the charger

can be shorted by foreign material. Foreign materials of a conductive nature, such as, but not
limited to, grinding dust, metal chips, steel wool, aluminum foil or any buildup of metallic particles
should be kept away from the charger cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug the charger before attempting to clean.
•

DO NOT attempt to charge the battery pack with any chargers other than the ones

in this manual.

The charger and battery pack are specifically designed to work together.

•

These chargers are not intended for any uses other than charging D

E

WALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock or

electrocution.

•

Do not expose the charger to rain or snow.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter

.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D

E

W

A

L

T

• www

.dewalt.com