Cypress CY7C1473BV25 - Manual
Cypress CY7C1473BV25 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – Pin Configurations
- Page 6 – TMS
- Page 9 – Functional Overview; Single Read Accesses; “Truth Table for
- Page 10 – ZZ Mode Electrical Characteristics
- Page 13 – Disabling the JTAG Feature; through a pull up resistor. TDO must be left unconnected.; Performing a TAP Reset; A RESET is performed by forcing TMS HIGH (V; Figure 3. TAP Controller State Diagram; Figure 4. TAP Controller Block Diagram
- Page 14 – TAP Registers; “TAP Controller Block Diagram”; BYPASS instruction is executed.; TAP Instruction Set; “Identification
- Page 15 – plus t; BYPASS; Figure 5. TAP Timing; T e st Clo ck
- Page 16 – T D O; TAP DC Electrical Characteristics And Operating Conditions
- Page 20 – Electrical Characteristics
- Page 22 – Switching Characteristics; “AC Test Loads and
- Page 23 – Switching Waveforms; Figure 8
- Page 24 – Figure 9. NOP, STALL and DESELECT Cycles
- Page 25 – shows ZZ Mode timing waveform.; Mode Timing; CLK
- Page 26 – Ordering Information; for actual products offered.
- Page 27 – Package Diagrams
- Page 30 – Document History Page; Issue
72-Mbit (2M x 36/4M x 18/1M x 72)
Flow-Through SRAM with NoBL™ Architecture
CY7C1471BV25
CY7C1473BV25, CY7C1475BV25
Cypress Semiconductor Corporation
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Document #: 001-15013 Rev. *E
Revised February 29, 2008
Features
■
No Bus Latency™ (NoBL™) architecture eliminates dead
cycles between write and read cycles
■
Supports up to 133 MHz bus operations with zero wait states
■
Data transfers on every clock
■
Pin compatible and functionally equivalent to ZBT™ devices
■
Internally self timed output buffer control to eliminate the need
to use OE
■
Registered inputs for flow through operation
■
Byte Write capability
■
2.5V IO supply (V
DDQ
)
■
Fast clock-to-output times
❐
6.5 ns (for 133-MHz device)
■
Clock Enable (CEN) pin to enable clock and suspend operation
■
Synchronous self timed writes
■
Asynchronous Output Enable (OE)
■
CY7C1471BV25, CY7C1473BV25 available in
JEDEC-standard Pb-free 100-pin TQFP, Pb-free and
non-Pb-free 165-ball FBGA package. CY7C1475BV25
available in Pb-free and non-Pb-free 209-ball FBGA package.
■
Three Chip Enables (CE
1
, CE
2
, CE
3
) for simple depth
expansion.
■
Automatic power down feature available using ZZ mode or CE
deselect.
■
IEEE 1149.1 JTAG Boundary Scan compatible
■
Burst Capability - linear or interleaved burst order
■
Low standby power
Functional Description
The CY7C1471BV25, CY7C1473BV25, and CY7C1475BV25
are 2.5V, 2M x 36/4M x 18/1M x 72 synchronous flow through
burst SRAMs designed specifically to support unlimited true
back-to-back read or write operations without the insertion of
wait states. The CY7C1471BV25, CY7C1473BV25, and
CY7C1475BV25 are equipped with the advanced No Bus
Latency (NoBL) logic required to enable consecutive read or
write operations with data transferred on every clock cycle. This
feature dramatically improves the throughput of data through the
SRAM, especially in systems that require frequent write-read
transitions.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock input is qualified by the
Clock Enable (CEN) signal, which when deasserted suspends
operation and extends the previous clock cycle. Maximum
access delay from the clock rise is 6.5 ns (133-MHz device).
Write operations are controlled by two or four Byte Write Select
(BW
X
) and a Write Enable (WE) input. All writes are conducted
with on-chip synchronous self timed write circuitry.
Three synchronous Chip Enables (CE
1
, CE
2
, CE
3
) and an
asynchronous Output Enable (OE) provide easy bank selection
and output tri-state control. To avoid bus contention, the output
drivers are synchronously tri-stated during the data portion of a
write sequence.
For best practice recommendations, refer to the Cypress appli-
cation note
AN1064, SRAM System Guidelines.
Selection Guide
Description
133 MHz
100 MHz
Unit
Maximum Access Time
6.5
8.5
ns
Maximum Operating Current
305
275
mA
Maximum CMOS Standby Current
120
120
mA
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CY7C1471BV25 CY7C1473BV25, CY7C1475BV25 Document #: 001-15013 Rev. *E Page 4 of 30 Pin Configurations A A A A A1 A0 NC/288M NC/ 144M V SS V DD A A A A A A DQP B DQ B DQ B V DDQ V SS DQ B DQ B DQ B DQ B V SS V DDQ DQ B DQ B V SS NC V DD DQ A DQ A V DDQ V SS DQ A DQ A DQ A DQ A V SS V DDQ DQ A DQ A DQ...
CY7C1471BV25 CY7C1473BV25, CY7C1475BV25 Document #: 001-15013 Rev. *E Page 6 of 30 Pin Configurations (continued) 165-Ball FBGA (15 x 17 x 1.4 mm) Pinout CY7C1471BV25 (2M x 36) 2 3 4 5 6 7 1 A B CD E F G H J K L M N P R TDO NC/576M NC/1G DQP C DQ C DQP D NC DQ D CE 1 BW B CE 3 BW C CEN A CE2 DQ C DQ...
CY7C1471BV25 CY7C1473BV25, CY7C1475BV25 Document #: 001-15013 Rev. *E Page 9 of 30 Functional Overview The CY7C1471BV25, CY7C1473BV25, and CY7C1475BV25are synchronous flow through burst SRAMs designed specifi-cally to eliminate wait states during write read transitions. Allsynchronous inputs pass th...
