Cypress CY7C1471BV33 - Manual
Cypress CY7C1471BV33 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – Pin Configuration
- Page 6 – TMS
- Page 8 – Pin Definitions
- Page 9 – Functional Overview; Single Read Accesses
- Page 10 – Single Write Accesses; Truth Table for; Burst Write Accesses; Single Write; Sleep Mode; Interleaved Burst Address Table
- Page 11 – Truth Table
- Page 13 – Disabling the JTAG Feature; Performing a TAP Reset; TAP Registers; nstruction Register; Boundary Scan Register
- Page 14 – TAP Instruction Set; “Identification
- Page 15 – TAP Controller State Diagram; R E SE T
- Page 16 – TAP Controller Block Diagram
- Page 17 – V TAP AC Output Load Equivalent; T D O; TAP DC Electrical Characteristics and Operating Conditions
- Page 18 – T e st Clo ck
- Page 22 – Electrical Characteristics
- Page 24 – Switching Characteristics
- Page 25 – Switching Waveforms; Figure 5
- Page 27 – Mode Timing; CLK
- Page 28 – Ordering Information; for actual products offered.
- Page 29 – Package Diagrams
- Page 32 – Document History Page; Issue; See ECN
CY7C1471BV33
CY7C1473BV33, CY7C1475BV33
72-Mbit (2M x 36/4M x 18/1M x 72) Flow-Through
SRAM with NoBL™ Architecture
Cypress Semiconductor Corporation
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Document #: 001-15029 Rev. *B
Revised March 05, 2008
Features
■
No Bus Latency™ (NoBL™) architecture eliminates dead
cycles between write and read cycles
■
Supports up to 133 MHz bus operations with zero wait states
■
Data is transferred on every clock
■
Pin compatible and functionally equivalent to ZBT™ devices
■
Internally self timed output buffer control to eliminate the need
to use OE
■
Registered inputs for flow through operation
■
Byte Write capability
■
3.3V/2.5V IO supply (V
DDQ
)
■
Fast clock-to-output times
❐
6.5 ns (for 133 MHz device)
■
Clock Enable (CEN) pin to enable clock and suspend operation
■
Synchronous self-timed writes
■
Asynchronous Output Enable (OE)
■
CY7C1471BV33, CY7C1473BV33 available in
JEDEC-standard Pb-free 100-pin TQFP, Pb-free and
non-Pb-free 165-Ball FBGA package. CY7C1475BV33
available in Pb-free and non-Pb-free 209-Ball FBGA package
■
Three Chip Enables (CE
1
, CE
2
, CE
3
) for simple depth
expansion
■
Automatic power down feature available using ZZ mode or CE
deselect
■
IEEE 1149.1 JTAG Boundary Scan compatible
■
Burst Capability—linear or interleaved burst order
■
Low standby power
Functional Description
The CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33
are 3.3V, 2M x 36/4M x 18/1M x 72 synchronous flow through
burst SRAMs designed specifically to support unlimited true
back-to-back read or write operations without the insertion of
wait states. The CY7C1471BV33, CY7C1473BV33, and
CY7C1475BV33 are equipped with the advanced No Bus
Latency (NoBL) logic. NoBL™ is required to enable consecutive
read or write operations with data being transferred on every
clock cycle. This feature dramatically improves the throughput of
data through the SRAM, especially in systems that require
frequent write-read transitions.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock input is qualified by the
Clock Enable (CEN) signal, which when deasserted suspends
operation and extends the previous clock cycle. Maximum
access delay from the clock rise is 6.5 ns (133 MHz device).
Write operations are controlled by two or four Byte Write Select
(BW
X
) and a Write Enable (WE) input. All writes are conducted
with on-chip synchronous self timed write circuitry.
Three synchronous Chip Enables (CE
1
, CE
2
, CE
3
) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. To avoid bus contention,
the output drivers are synchronously tri-stated during the data
portion of a write sequence. For best practice recommendations,
refer to the Cypress application note
“SRAM System
Guidelines”.
Selection Guide
Description
133 MHz
117 MHz
Unit
Maximum Access Time
6.5
8.5
ns
Maximum Operating Current
305
275
mA
Maximum CMOS Standby Current
120
120
mA
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CY7C1471BV33 CY7C1473BV33, CY7C1475BV33 Document #: 001-15029 Rev. *B Page 4 of 32 Pin Configuration A A A A A1 A0 NC/288M NC /144M V SS V DD A A A A A A DQP B DQ B DQ B V DDQ V SS DQ B DQ B DQ B DQ B V SS V DDQ DQ B DQ B V SS NC V DD DQ A DQ A V DDQ V SS DQ A DQ A DQ A DQ A V SS V DDQ DQ A DQ A DQP...
CY7C1471BV33 CY7C1473BV33, CY7C1475BV33 Document #: 001-15029 Rev. *B Page 6 of 32 Pin Configuration (continued) 165-Ball FBGA (15 x 17 x 1.4 mm) Pinout CY7C1471BV33 (2M x 36) CY7C1473BV33 (4M x 18) 2 3 4 5 6 7 1 A B CD E F G H J K L M N P R TDO NC/576M NC/1G DQP C DQ C DQP D NC DQ D CE 1 BW B CE 3 ...
CY7C1471BV33 CY7C1473BV33, CY7C1475BV33 Document #: 001-15029 Rev. *B Page 8 of 32 Pin Definitions Name IO Description A 0 , A 1 , A Input- Synchronous Address Inputs used to select one of the Address Locations . Sampled at the rising edge of the CLK. A [1:0] is fed to the two-bit burst counter. BW ...
