Cypress CY7C1364C - Manual
Cypress CY7C1364C – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Selection Guide; Unit; Pin Configuration
- Page 4 – Pin Definitions
- Page 5 – Functional Overview
- Page 6 – ZZ Mode Electrical Characteristics
- Page 7 – Truth Table
- Page 8 – Truth Table for Read/Write
- Page 9 – Electrical Characteristics
- Page 10 – Capacitance; Thermal Resistance; AC Test Loads and Waveforms
- Page 11 – Switching Characteristics
- Page 12 – Switching Waveforms; Read Cycle Timing
- Page 13 – Write Cycle Timing
- Page 14 – Read/Write Cycle Timing
- Page 15 – ZZ Mode Timing; CLK
- Page 16 – Ordering Information
- Page 17 – Package Diagram
- Page 18 – Document History Page; Issue Date
CY7C1364C
9-Mbit (256K x 32) Pipelined Sync SRAM
Cypress Semiconductor Corporation
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Document #: 38-05689 Rev. *E
Revised September 14, 2006
Features
• Registered inputs and outputs for pipelined operation
• 256K × 32 common I/O architecture
• 3.3V core power supply (V
DD
)
• 2.5V/3.3V I/O power supply (V
DDQ
)
• Fast clock-to-output times
— 2.8 ns (for 250-MHz device)
• Provide high-performance 3-1-1-1 access rate
• User-selectable burst counter supporting Intel
®
Pentium
®
interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed writes
• Asynchronous output enable
• Available in JEDEC-standard lead-free 100-Pin TQFP
package
• TQFP Available with 3-Chip Enable and 2-Chip Enable
• “ZZ” Sleep Mode Option
Functional Description
[1]
The CY7C1364C SRAM integrates 256K x 32 SRAM cells with
advanced synchronous peripheral circuitry and a two-bit
counter for internal burst operation. All synchronous inputs are
gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CE
1
), depth-expansion Chip Enables (CE
2
and CE
3
[2]
), Burst
Control inputs (ADSC, ADSP, and ADV), Write Enables
(BW
[A:D]
, and BWE), and Global Write (GW). Asynchronous
inputs include the Output Enable (OE) and the ZZ pin.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
Address, data inputs, and write controls are registered on-chip
to initiate a self-timed Write cycle.This part supports Byte Write
operations (see Pin Descriptions and Truth Table for further
details). Write cycles can be one to four bytes wide as
controlled by the Byte Write control inputs. GW when active
LOW causes all bytes to be written.
The CY7C1364C operates from a +3.3V core power supply
while all outputs may operate with either a +2.5 or +3.3V
supply. All inputs and outputs are JEDEC-standard
JESD8-5-compatible.
Notes:
1. For best-practices recommendations, please refer to the Cypress application note
System Design Guidelines
on www.cypress.com.
2. CE
3
is not available on 2 Chip Enable TQFP package.
Logic Block Diagram-CY7C1364C (256K x 32)
ADDRESS
REGISTER
ADV
CLK
BURST
COUNTER
AND
LOGIC
CLR
Q1
Q0
ADSP
ADSC
MODE
BWE
GW
CE
1
CE
2
CE
3
OE
ENABLE
REGISTER
OUTPUT
REGISTERS
SENSE
AMPS
OUTPUT
BUFFERS
E
PIPELINED
ENABLE
INPUT
REGISTERS
A0, A1, A
BW
B
BW
C
BW
D
BW
A
MEMORY
ARRAY
D Q s
SLEEP
CONTROL
ZZ
A
[1:0]
2
DQ
A
BYTE
WRITE REGISTER
DQ
B
BYTE
WRITE REGISTER
DQ
C
BYTE
WRITE REGISTER
DQ
D
BYTE
WRITE REGISTER
DQ
A
BYTE
WRITE DRIVER
DQ
B
BYTE
WRITE DRIVER
DQ
C
BYTE
WRITE DRIVER
DQ
D
BYTE
WRITE DRIVER
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CY7C1364C Document #: 38-05689 Rev. *E Page 2 of 18 Selection Guide 250 MHz 200 MHz 166 MHz Unit Maximum Access Time 2.8 3.0 3.5 ns Maximum Operating Current 250 220 180 mA Maximum CMOS Standby Current 40 40 40 mA Pin Configuration A A A A A 1 A 0 NC NC V SS V DD NC NC A A A A A A A NCDQ B DQ B V DD...
CY7C1364C Document #: 38-05689 Rev. *E Page 4 of 18 Pin Definitions Name TQFP I/O Description A 0 , A 1 , A 37, 36, 32, 33, 34, 35, 43, 44, 45, 46, 47, 48, 49, 50, 81, 82, 99, 100 Input- Synchronous Address Inputs used to select one of the 256K address locations . Sampled at the rising edge of the C...
CY7C1364C Document #: 38-05689 Rev. *E Page 5 of 18 Functional Overview All synchronous inputs pass through input registers controlledby the rising edge of the clock. All data outputs pass throughoutput registers controlled by the rising edge of the clock. The CY7C1364C supports secondary cache in s...
