Cypress CY7C1352G - Manual
Cypress CY7C1352G – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Selection Guide; Unit; Pin Configuration
- Page 3 – Pin Definitions
- Page 4 – Functional Overview; Single Read Accesses
- Page 5 – ZZ Mode Electrical Characteristics
- Page 6 – Electrical Characteristics
- Page 8 – Switching Characteristics
- Page 9 – Switching Waveforms
- Page 10 – ZZ Mode Timing; CLK
- Page 12 – Document History Page; Issue
4-Mbit (256K x 18) Pipelined SRAM with
NoBL™ Architecture
CY7C1352G
Cypress Semiconductor Corporation
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Document #: 38-05514 Rev. *D
Revised July 4, 2006
Features
• Pin compatible and functionally equivalent to ZBT™
devices
• Internally self-timed output buffer control to eliminate
the need to use OE
• Byte Write capability
• 256K x 18 common I/O architecture
• 3.3V core power supply (V
DD
)
• 2.5V/3.3V I/O power supply (V
DDQ
)
• Fast clock-to-output times
— 2.6 ns (for 250-MHz device)
• Clock Enable (CEN) pin to suspend operation
• Synchronous self-timed writes
• Asynchronous output enable (OE)
• Available in lead-free 100-Pin TQFP package
• Burst Capability—linear or interleaved burst order
• ZZ” Sleep Mode Option and Stop Clock option
Functional Description
[1]
The CY7C1352G is a 3.3V, 256K x 18 synchronous-pipelined
Burst SRAM designed specifically to support unlimited true
back-to-back Read/Write operations without the insertion of
wait states. The CY7C1352G is equipped with the advanced
No Bus Latency™ (NoBL™) logic required to enable consec-
utive Read/Write operations with data being transferred on
every clock cycle. This feature dramatically improves the
throughput of the SRAM, especially in systems that require
frequent Write/Read transitions.
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock. The
clock input is qualified by the Clock Enable (CEN) signal,
which, when deasserted, suspends operation and extends the
previous clock cycle. Maximum access delay from the clock
rise is 2.6 ns (250-MHz device).
Write operations are controlled by the two Byte Write Select
(BW
[A:B]
) and a Write Enable (WE) input. All writes are
conducted with on-chip synchronous self-timed write circuitry.
Three synchronous Chip Enables (CE
1
, CE
2
, CE
3
) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. In order to avoid bus
contention, the output drivers are synchronously tri-stated
during the data portion of a write sequence.
Note:
1. For best-practices recommendations, please refer to the Cypress application note
System Design Guidelines
on www.cypress.com.
A0, A1, A
C
MODE
BW
A
BW
B
WE
CE1
CE2
CE3
OE
READ LOGIC
DQs
DQP
A
DQP
B
D
A
T
A
S
T
E
E
R
I
N
G
O
U
T
P
U
T
B
U
F
F
E
R
S
MEMORY
ARRAY
E
E
INPUT
REGISTER 0
ADDRESS
REGISTER 0
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BURST
LOGIC
A0'
A1'
D1
D0
Q1
Q0
A0
A1
C
ADV/LD
ADV/LD
E
INPUT
REGISTER 1
S
E
N
S
E
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
E
CLK
CEN
WRITE
DRIVERS
ZZ
Sleep
Control
Logic Block Diagram
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CY7C1352G Document #: 38-05514 Rev. *D Page 2 of 12 Selection Guide 250 MHz 200 MHz 166 MHz 133 MHz Unit Maximum Access Time 2.6 2.8 3.5 4.0 ns Maximum Operating Current 325 265 240 225 mA Maximum CMOS Standby Current 40 40 40 40 mA Pin Configuration A A A A A 1 A 0 NC/2 88M NC /144M V SS V DD N C /...
CY7C1352G Document #: 38-05514 Rev. *D Page 3 of 12 Pin Definitions Name I/O Description A0, A1, A Input- Synchronous Address Inputs used to select one of the 256K address locations . Sampled at the rising edge of the CLK. A [1:0] are fed to the two-bit burst counter. BW [A:B] Input- Synchronous Byt...
CY7C1352G Document #: 38-05514 Rev. *D Page 4 of 12 Functional Overview The CY7C1352G is a synchronous-pipelined Burst SRAMdesigned specifically to eliminate wait states duringWrite/Read transitions. All synchronous inputs pass throughinput registers controlled by the rising edge of the clock. Thecl...
