Cypress CY7C1330AV25 - Manual
Cypress CY7C1330AV25 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PRELIMINARY; Selection Guide; Unit; Pin Configurations
- Page 3 – Pin Definitions
- Page 4 – Introduction; Functional Overview; Pipelined Read Accesses; Sleep Mode
- Page 5 – Cycle Description Truth Table
- Page 6 – Instruction Register; ) when the BYPASS instruction is executed.
- Page 7 – EXTEST; BYPASS
- Page 8 – TAP Controller State Diagram
- Page 9 – TAP Controller Block Diagram
- Page 10 – TAP Timing and Test Conditions; Test Clock; Identification Register Definitions
- Page 11 – Scan Register Sizes
- Page 12 – Bump ID
- Page 13 – Maximum Ratings; Electrical Characteristics
- Page 14 – AC Test Loads and Waveforms; Capacitance; Thermal Resistance
- Page 15 – Switching Characteristics
- Page 16 – Switching Waveforms; ADDRESS
- Page 17 – CLK
- Page 18 – Ordering Information; Commercial; Package Diagram
- Page 19 – Document History Page; Issue Date
PRELIMINARY
18-Mbit (512K x 36/1Mbit x 18)
Pipelined Register-Register Late Write
CY7C1330AV25
CY7C1332AV25
Cypress Semiconductor Corporation
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Document No: 001-07844 Rev. *A
Revised September 20, 2006
Features
• Fast clock speed: 250, 200 MHz
• Fast access time: 2.0, 2.25 ns
• Synchronous Pipelined Operation with Self-timed Late
Write
• Internally synchronized registered outputs eliminate
the need to control OE
• 2.5V core supply voltage
• 1.4–1.9V V
DDQ
supply with V
REF
of 0.68–0.95V
— Wide range HSTL I/O Levels
• Single Differential HSTL clock Input K and K
• Single WE (READ/WRITE) control pin
• Individual byte write (BWS
[a:d]
) control (may be tied
LOW)
• Common I/O
• Asynchronous Output Enable Input
• Programmable Impedance Output Drivers
• JTAG boundary scan for BGA packaging version
• Available in a 119-ball BGA package (CY7C1330AV25
and CY7C1332AV25)
Configuration
CY7C1330AV25 – 512K x 36
CY7C1332AV25 – 1M x 18
Functional Description
The CY7C1330AV25 and CY7C1332AV25 are high perfor-
mance, Synchronous Pipelined SRAMs designed with late
write operation. These SRAMs can achieve speeds up to 250
MHz. Each memory cell consists of six transistors.
Late write feature avoids an idle cycle required during the
turnaround of the bus from a read to a write.
All synchronous inputs are gated by registers controlled by a
positive-edge-triggered Clock Input (K). The synchronous
inputs include all addresses (A), all data inputs (DQ
[a:d]
), Chip
Enable (CE), Byte Write Selects (BWS
[a:d]
), and read-write
control (WE). Read or Write Operations can be initiated with
the chip enable pin (CE). This signal allows the user to
select/deselect the device when desired.
Power down feature is accomplished by pulling the
Synchronous signal ZZ HIGH.
Output Enable (OE) is an asynchronous input signal. OE can
be used to disable the outputs at any given time.
Four pins are used to implement JTAG test capabilities. The
JTAG circuitry is used to serially shift data to and from the
device. JTAG inputs use LVTTL/LVCMOS levels to shift data
during this testing mode of operation.
K,K
A
x
WE
BWS
x
CE
OE
512Kx36
Logic Block Diagram
DQ
x
Data-In REG.
Q
D
CE
CONTROL
and WRITE
LOGIC
ZZ
1Mx18
OUT
O
UT
REGISTERS
a
nd L
OGIC
512Kx36
1Mx18
A
X
DQ
X
BWS
X
X = 18:0
X = 19:0
X = a, b
X = a, b, c, d
X = a, b
X = a, b, c, d
Clock
Buffer
MEMORY
ARRAY
(2stage)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PRELIMINARY CY7C1330AV25CY7C1332AV25 Document No: 001-07844 Rev. *A Page 2 of 19 Selection Guide CY7C1330AV25-250CY7C1332AV25-250 CY7C1330AV25-200 CY7C1332AV25- 200 Unit Maximum Access Time 2.0 2.25 ns Maximum Operating Current 600 550 mA Maximum CMOS Standby Current 280 260 mA Pin Configurations 2 ...
PRELIMINARY CY7C1330AV25CY7C1332AV25 Document No: 001-07844 Rev. *A Page 3 of 19 Pin Definitions Name I/O Type Description A Input- Synchronous Address Inputs used to select one of the address locations . Sampled at the rising edge of the K. BWS a BWS b BWS c BWS d Input- Synchronous Byte Write Sele...
PRELIMINARY CY7C1330AV25CY7C1332AV25 Document No: 001-07844 Rev. *A Page 4 of 19 Introduction Functional Overview The CY7C1330AV25 and CY7C1332AV25 are synchronous-pipelined Late Write SRAMs running at speeds up to 250 MHz.All synchronous inputs pass through input registers controlledby the rising e...
