ClearSounds CL600 - Manual

5 Using the volume reset override Page 24 Using the outgoing speech volume Page 25 Using the last number redial Page 25 Using the fl ash button Page 25 Using the mute button Page 25 CL600 Caller ID Operation Viewing your Caller ID display Page 26 Viewing incoming calls Page 27 New calls / message wa...

9 OK button is used to con fi rm action or a choice on the screen. “UP / DOWN arrow” buttons are used to highlight or scroll through the menu. C button is used to cancel or con fi rm an action/entry or clear a stored Caller ID call. Your CL600 Phone has a screen with different icons, which help you ...

10 Installation Steps Installation of your ClearSounds ™ CL600 Emergency Connect Phone is easy. There are some basic steps you need to take when you set-up your CL600 Emergency Connect Phone for the fi rst time. 1. Check parts list.2. Install (4) AAA Alkaline batteries (not included). Batteries are ...

11 PHONE MOUNTING INSTALLATIONS Choose a location for the CL600 Emergency Connect Telephone that is as central as possible in the house, while providing access to a modular jack and an AC outlet. The telephone may be placed on a shelf or table, or may be fi xed to a wall using the mounting bracket. ...

12 5. Holding the phone slightly above the mounting screws on the wall jack, push the phone against the mounting screws so they are hooked into upper and lower key-hole slots on the back of the phone. Slowly slide the phone down until it snaps into place (See diagram #10) . 6. Connect the handset co...

13 PROGRAMMING THE RINGER & AUXILIARY ALERT Ringer Volume: You can adjust the ringer volume of your CL600 as high as 95+ dB. The ringer volume adjustment is located on the right side of the telephone. The settings are OFF, LO, HI, (See diagram #11) . Your phone comes with the ringer switched to ...

14 Your CL600 Phone is equipped with a bright STROBE light, which fl ashes a very bright strobe when the phone rings (See diagram #13) . It’s almost impossible to miss telephone calls when you select the Strobe Ringer. If you purchased the optional Bed Shaker, simply plug it into the shaker jack (Se...

15 To program your one-touch memory dial buttons please follow instructions below: 1. Lift the handset.2. Press the PROG (program) button (See diagram #16). 3. Using the keypad, dial the number you would like to save, including “1” and the area code (if applicable). (See diagram #17) . 4. Press one ...

16 CL600 Emergency Connect Phone Operation The ClearSounds ™ CL600 Emergency Connect Phone allows you to ask for help con- veniently when there is an emergency. To activate the function, you need to preset the emergency connect SOS number and record an emergency connect SOS message, which will be he...

18 Phone will dial the next emergency connect SOS number automatically. NOTE : The friend, relative or neighbor whom you have chosen are required to have touch- tone phone service and a phone that will generate touch-tone code. Test the CL600 emergency connect phone 1. Make sure the phone numbers an...

20 AUTO ON HOOK When the Auto On Hook feature is ON, Your ClearSounds CL600 will automatically discon-nect the line after 5 - 8 minutes if the phone is left off the hook. This will restore your line to be able to receive another call even if you leave the handset off the base.In the hook position, 1...

21 a. Dial a number from the keypadb. Press one of the Priority or Memory dial buttons (See pages 14-15 for instructions on programming Priority/Memory Dial Buttons.) c. Dial from your Phone Book or Caller ID (See page 34 for instructions on setting up your Phone Book.) 4. On completion of the call,...

23 Using the Ampli fi cation Function The CL600 Phone has an AMPLI button that controls the loudness and tone of the hand- set. Without pressing the AMPLI button, you are able to amplify the handset up to 30 dB of ampli fi cation. Once the AMPLI button is pressed, an extra level of ampli fi cation i...

25 Using the Outgoing Speech Volume You can adjust the sending volume (outgoing volume up to 12 dB of gain) by using the Speech Volume Control located on the right side of your CL600 phone. If your voice is faint or weak, adjust the volume to “ HI ”. You can also decrease the volume as well. There a...

26 available in all areas. This product can provide information only if both you and the caller are in areas offering Caller ID service, and if both telephone companies use compatible equipment. Viewing Your Display Screen: Your CL600 Emergency Connect Telephone has a large LCD screen that provides ...

27 Viewing Incoming Calls If you subscribe to Caller ID service with your local phone service provider, this phone stores all incoming calls with valid Caller ID information in the call history. Your LCD screen will display the time and date, the caller’s phone number and name (if they are sent with...

28 Turn OFF the New Calls / Message Waiting Indicator Light This red light (See diagram #35) will remain lit unless you do one of the following in the hook position: 1. If you do not have Caller ID or Message Waiting Service, your CL600 will alert you that you have missed a call by causing the red i...

29 5. Press the C button to con fi rm. 6. Press the OK button to exit. NOTE : Once a call is removed from call history, it cannot be retrieved. Call Waiting Your CL600 Phone also has a Caller ID with Call Waiting feature that works with your service from the local phone service provider. Caller ID w...

31 5. Press the OK button. 6. Using the arrow buttons, enter your area code. After each number press the OK but- ton. The phone accommodates up to six (6) digits (allows for International codes). Once you have entered your area code, even if you are not using all six (6) digits, press the OK button ...

32 5. Press the OK button. 6. Using the arrow buttons, select <<DAY-MONTH>> or <<MONTH-DAY>> . 7. Press the OK button. 8. Press the C button twice to exit. Hour format You can choose between (2) two formats:12 hours or 24 hoursIn the hook position, 1. Press the MUTE button to...

34 4. Using the or arrow buttons, scroll to select <<REVIEW>> . 5. Press the OK button. 6. Using the arrow buttons to locate the number you want to delete.7. Press the C button, then the LCD Screen will display <<DEL?>> . 8. Press C button once more to con fi rm. To Save Numb...

35 4. Press the C button. 5. The Screen will display “ DEL? ” 6. Press again the C button to con fi rm. 7. Press the OK button to exit. Auto On Hook Should you leave the CL600 or another telephone off the hook, when the Auto On Hook feature is ON , your ClearSounds CL600 will automatically hang-up t...

36 There is a red light that continues to fl ash 1. You have un-reviewed Caller ID / Call Waiting information or missed a call (See page #28). 2. Your Voice Mail account needs to be set-up as Visual Indicator only. Contact your local phone company; if the account is setup as Audible or Audible/Visua...

37 Maintenance and Care The CL600 Emergency Connect Telephone has been designed to give you years of de-pendable service with a minimum of care. To ensure the utmost in performance, follow these guidelines in caring for your phone: 1. Avoid dropping or knocking the unit.2. Dust the unit regularly. U...

38 Speci fi cations Maximum Gain: 42 dB in Wide band (300 to 3400Hz)52 dB max Low Frequency (Bass 300 Hz)52 dB max High Frequency (Treble 3400Hz) Maximum Outgoing Gain: +12 dB Dimensions: Size: 10.5” (with Caller ID screen fl at) X 8” X 2” Weight: 4.33 lbs Power Requirements: AC Power Adapter: Input...

39 represented by 10 are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.] e) If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service m...