Page 3 - C O N T E N T S; Preface; Cisco 170 Series Appliance; Preparing for Installation
iii Cisco 170 Series Hardware Installation Guide OL-28365-01 C O N T E N T S Preface vii Contents vii Document Objectives vii Audience vii Document Organization viii Document Conventions viii Installation Warnings ix Where to Find Safety and Warning Information xiii Related Documentation xiii Obtain...
Page 4 - Installing and Connecting the Cisco 170 Series Appliance; Maintaining the Cisco 170 Series Appliance; Identifying Cable Pinouts
Contents iv Cisco 170 Series Hardware Installation Guide OL-28365-01 Preventive Site Configuration 2-4 Power Supply Considerations 2-5 Configuring Equipment Racks 2-7 C H A P T E R 3 Installing and Connecting the Cisco 170 Series Appliance 3--1 Installing the Cisco 170 Series Appliance with Slide Ra...
Page 5 - Document Objectives; Audience
vii Cisco 170 Series Hardware Installation Guide OL-28365-01 Preface Contents This preface includes the following sections: • Document Objectives, page vii • Audience, page vii • Document Organization, page viii • Document Conventions, page viii • Installation Warnings, page ix • Where to Find Safet...
Page 6 - Document Organization
viii Cisco 170 Series Hardware Installation Guide OL-28365-01 Document Organization This guide includes the following sections: Document Conventions Command descriptions use these conventions: • Braces ({ }) indicate a required choice. • Square brackets ([ ]) indicate optional elements. • Vertical b...
Page 7 - Installation Warnings; Power Supply Disconnection Warning; Jewelry Removal Warning
ix Cisco 170 Series Hardware Installation Guide OL-28365-01 Installation Warnings Before installing the appliance, be sure to read the Safety and Compliance Guide for the Cisco Content Security Appliances document at: http://www.cisco.com/en/US/docs/security/esa/hw/SafetyAndComplianceGuide.pdf . Thi...
Page 10 - Grounded Equipment Warning; Safety Cover Requirement; Faceplates and Cover Panel Requirement
xii Cisco 170 Series Hardware Installation Guide OL-28365-01 Grounded Equipment Warning Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39 Safety Cover Requirement Warning The safety cover is an integral part of the pr...
Page 11 - Where to Find Safety and Warning Information; Related Documentation
xiii Cisco 170 Series Hardware Installation Guide OL-28365-01 Where to Find Safety and Warning Information For safety and warning information, see the Safety and Compliance Guide for the Cisco Content Security Appliances document at the following URL: http://www.cisco.com/en/US/docs/security/esa/hw/...
Page 13 - Cisco 170 Series Overview
C H A P T E R 1-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 1 Cisco 170 Series Appliance We recommend that you read the entire guide before beginning any of the procedures contained herein. Warning Only trained and qualified personnel should install, replace, or service this equipment...
Page 14 - Cisco M170 Content Security Management Appliance; Cisco S170 Web Security Appliance
1-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Cisco C170 Email Security Appliance Cisco C170 Email Security Appliance (Cisco C170) automatically stops spam, viruses, and other anomalies. It prevents and responds to multilevel threats and includes capabilities such as: spam and...
Page 15 - Cisco 170 Series Appliance Panels; Front Panel LEDs
1-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Figure 1-3 shows the Cisco S170 front panel view. Figure 1-3 Cisco S170 Web Security Appliance Cisco 170 Series Appliance Panels This section describes the front and rear Cisco 170 series appliance panels. It includes the following...
Page 17 - Rear Panel LEDs
1-5 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Rear Panel LEDs This section describes the rear panel LEDs for the Cisco 170 series appliance. Figure 1-5 shows the rear panel LEDs that are available for the Cisco C170, Cisco M170 and Cisco S170 models (graphic shows the Cisco S1...
Page 18 - Rear Panel Ports
1-6 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Rear Panel Ports This section describes the rear panel ports on the Cisco 170 series appliance. Figure 1-6 and Figure 1-7 show the rear panel and ports that are available on the Cisco S170 model. Figure 1-6 Rear Panel and Ports for...
Page 20 - Alarm LED; Management Interface
1-8 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Alarm LED The Cisco 170 series appliance performs autonomous environment monitoring to poll all external sensors and monitor operating conditions. In the event of damage to certain internal components or surpassed temperature thres...
Page 21 - Hardware and Technical Specifications
1-9 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Hardware and Technical Specifications Table 1-1 contains hardware and technical specifications for the Cisco 170 series. Table 1-1 Hardware and Technical Specifications for Cisco C170, Cisco M170 and Cisco S170 Specifications Cisco...
Page 23 - Installation Overview
C H A P T E R 2-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 2 Preparing for Installation This chapter describes the steps to follow before installing the Cisco 170 series appliance or performing hardware maintenance. It includes the following sections: • Installation Overview, page 2-...
Page 24 - Safety Recommendations; Maintaining Safety with Electricity
2-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter • Cisco M170 Content Security Management Appliance Quick Start Guide: http://www.cisco.com/en/US/docs/security/security_management/sma/hw/quick_start/M170_QSG.pdf • Cisco S170 Web Security Appliance Quick Start Guide : http://www.c...
Page 25 - Preventing Electrostatic Discharge Damage
2-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter • If an electrical accident occurs, proceed as follows: – Use caution; do not become a victim yourself. – Disconnect power from the system. – If possible, send another person to get medical aid. Otherwise, assess the condition of t...
Page 26 - General Site Requirements; Site Environment; Preventive Site Configuration
2-4 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter General Site Requirements The topics in this section describe the requirements your site must meet for safe installation and operation of your Cisco 170 series system. Ensure that your site is properly prepared before beginning ins...
Page 27 - Power Supply Considerations
2-5 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Power Supply Considerations The Cisco 170 series hardware operates on AC power and supports the ability to restore the previous power state of the system in the event that AC power is lost. Be aware of the following when interactin...
Page 29 - Configuring Equipment Racks
2-7 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Configuring Equipment Racks The following tips help you plan an acceptable equipment rack configuration: • Enclosed racks must have adequate ventilation. Ensure that the rack is not overly congested because each appliance generates...
Page 31 - Installing the Cisco 170 Series Appliance with Slide Rails; Verifying the Box Contents
C H A P T E R 3--1 Cisco 170 Series Hardware Installation Guide OL-28365-01 3 Installing and Connecting the Cisco 170 Series Appliance This chapter describes how to install the Cisco 170 series (Cisco 170 series) appliance using slide rails (standard configuration) or rack-mounting it (optional conf...
Page 32 - Disassembling the Slide Rail
3-0 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter • A—Slide rails (x2) (preconfigured for square hole racks) • B— Phillips flat-head screws for Inner Slide (x2) For round hole racks, you also need the following: • C—Round hole inserts (x4) • Phillips screwdriver For threaded hole ...
Page 33 - Attaching Inner Rails to the Appliance
3-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Slide the plastic tab forward, and pull the inner slide rail to disconnect it from the outer slide rail. Step 3 Repeat the previous steps for the other slide rail. Attaching Inner Rails to the Appliance Step 1 Align one of t...
Page 34 - Verifying the Rack Type
3-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Use a Phillips screwdriver to secure the inner slide rail with one Phillips flat-head screw (See B in Figure 3-1 ). Step 3 Secure the other inner slide rail to the appliance by repeating the previous steps. Verifying the Rac...
Page 35 - Securing Round Hole Racks
3-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Securing Round Hole Racks Step 1 Using a Phillips head screwdriver, remove the square insert from the rear of the rail. Retain the two Phillips head screws. Step 2 Remove the square insert from the front of the rail. Retain the two...
Page 36 - Attaching the Outer Slide Rail to Round and Square Hole Racks
3-4 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Remove the square hole insert from the front of the rail. Step 3 Align the threaded hole bracket (see D in Figure 3-1 ) to the front of the rail over the hooks. Secure it with the threaded hole standoff (see E in Figure 3-1 ...
Page 37 - Attaching the Outer Slide Rail to Threaded Hole Racks
3-5 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Secure the other outer slide rail to the rack by repeating the previous steps. Step 3 Proceed to the “Installing the Appliance” section on page 3-6 . Attaching the Outer Slide Rail to Threaded Hole Racks Step 1 Align the sli...
Page 38 - Installing the Appliance
3-6 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Align the slide rail to the rear rack post. Secure it with two of the included Phillips pan-head screws (see F in Figure 3-1 ). Step 3 Align the other slide rail to the rack by repeating the previous steps. Step 4 Proceed to...
Page 39 - Securing the Appliance
3-7 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Pull the side release tabs to unlock the inner slide rail and push the appliance assembly into the rack. Securing the Appliance Step 1 Secure the appliance to the rack with the front captive screws. 330 8 9 8 330 8 90
Page 40 - Rack Mounting the Cisco 170 Series Appliance; Guidelines and Recommendations; Rack Mounting the Cisco C170, Cisco M170, or Cisco S170 Appliances
3-8 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Rack Mounting the Cisco 170 Series Appliance If you have 2-post racks, you can order the rack mount spares to rack-mount the Cisco 170 series appliance as described in this section. This section contains the following topics: • Gui...
Page 42 - Connecting the Interface Cables and Verifying Connectivity
3-10 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Figure 3-4 Attaching the C170, M170, or S170 Appliance to the Rack Connecting the Interface Cables and Verifying Connectivity This section describes how to connect the cables to the Console, Auxiliary, and Management ports. Warnin...
Page 45 - Fixed AC Power Supply; Removing and Installing Hard Disk Drives
C H A P T E R 4-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 4 Maintaining the Cisco 170 Series Appliance This chapter provides maintenance information about the Cisco 170 series appliance, including information on how to replace the pre-installed hard disk drives (HDDs). This chapter ...
Page 46 - Maintenance Scenarios; Replacing the Hard Disk Drives
4-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Maintenance Scenarios Note Make sure that you replace the Cisco 170 series HDDs with Cisco supplied HDDs that are specific to and preconfigured for the Cisco 170 series appliance. Please contact Cisco Technical Support for more inf...
Page 47 - Contacting Service and Support
4-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Figure 4-2 shows the Cisco 170 series appliance with one HDD being inserted. Figure 4-2 Installing a HDD in the Cisco 170 Series Appliance Step 3 On the front panel of the Cisco 170 series appliance, make sure the HDD1 and HDD0 ind...
