Cisco WS-C6513-E-RF - Manual

Cisco WS-C6513-E-RF

Cisco WS-C6513-E-RF – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
Page: / 34

Table of Contents:

  • Page 2 – Contents; CMM Module
  • Page 3 – Note; Color Description
  • Page 4 – -Port T1 and E1 Port Adapters; Table 3; Color
  • Page 5 – 4-Port FXS Port Adapter; Table 4; Warning
  • Page 6 – Ad-Hoc Conferencing and Transcoding Port Adapter; Figure 4; Requirements; Hardware Requirements, page 7
  • Page 7 – Hardware Requirements; The hardware requirements for the modules are as follows:; Software Requirements; For software requirements, see the; Safety Overview
  • Page 10 – Required Tools; Installing and Removing the Module; Installing the Module, page 10; Installing the Module
  • Page 13 – Figure 6
  • Page 15 – Figure 9
  • Page 16 – Caution
  • Page 17 – Tighten the two captive installation screws on the module.; Removing the Module
  • Page 18 – To remove a module from the chassis, perform these steps:
  • Page 19 – Removing and Replacing Port Adapters; Removing a Port Adapter from Module Slots 1 through 3, page 19; Removing a Port Adapter from Module Slots 1 through 3
  • Page 22 – Installing a Port Adapter in Module Slots 1 through 3
  • Page 24 – Tip
  • Page 25 – Verifying the Installation; show module; RJ-45 Port Connector and Cabling Specifications
  • Page 26 – Pin; Description
  • Page 27 – RJ-21 Port Connector and Cabling Specifications
  • Page 28 – Accessing the Port Adapter Ports; followed by; Signal; GND
  • Page 29 – Configuring the Port Adapter Ports; Configuring the Port Adapter Clock Source; command in controller configuration
  • Page 30 – Disaster Recovery for Module Software Upgrades; Supervisor Engine Model; Cisco IOS Software
  • Page 31 – “Removing and Replacing Port Adapters” section on page 19
  • Page 32 – alias; boot; reset; Password Recovery; “Removing the Module” section
  • Page 33 – Regulatory Standards Compliance; publication at this; Related Documentation
Loading the manual

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco Communication Media Module for
Catalyst 6500 Series Switch and Cisco 7600
Series Router Installation and Verification Note

Product Number: WS-SVC-CMM

Last Updated: March 23, 2009

This publication contains the procedures for installing and configuring the Catalyst 6500 series switch
and Cisco 7600 series router Communication Media Module (CMM). Installation and configuration
procedures are provided for the following CMM port adapters:

•

6-port T1 port adapter (WS-SVC-CMM-6T1)

•

6-port E1 port adapter (WS-SVC-CMM-6E1)

•

24-port FXS port adapter (WS-SVC-CMM-24FXS)

•

128-port ad-hoc conferencing and transcoding (ACT) port adapter (WS-SVC-CMM-ACT)

Note

Except where specifically differentiated, the term “Catalyst 6500 series switches” includes both the
Catalyst 6500 series switches and the Catalyst 6000 series switches.

Note

Throughout this publication, except where specifically differentiated, the term

supervisor engine

refers

to Supervisor Engine 1, Supervisor Engine 2, Supervisor Engine 720, and the Supervisor Engine 32.
Additionally, the term

Multilayer Switch Feature Card (MSFC)

refers to MSFC, MSFC2, and MSFC3.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Contents; CMM Module

Contents 2 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note Contents This publication contains these sections: • Front Panel Descriptions, page 2 • Requirements, page 6 • Safety Overview, page 7 • Required Tools, page 10...

Page 3 - Note; Color Description

Front Panel Descriptions 3 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note Note For information on the supervisor engine LEDs, see the Catalyst 6500 Series Switch Supervisor Engine Guide at this URL: http://www.cisco.co...

Page 4 - -Port T1 and E1 Port Adapters; Table 3; Color

Front Panel Descriptions 4 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note 6-Port T1 and E1 Port Adapters The front panel features of the 6-port T1 and E1 port adapters are as follows: • Receive port LEDs—The LEDs on th...

Other Cisco Models

All Cisco Other