Cisco V110 - Manual
Cisco V110 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Benefits; Transmission Speeds/Bearer Rates
- Page 3 – Related Features and Technologies; Supported Platforms
- Page 5 – show Command Examples
- Page 6 – show modem operational-status
- Page 7 – show modem log
- Page 10 – Debug Commands; Example Debug Commands for Cisco AS5200 and Cisco AS5300; Example Debug Commands for Cisco AS5800
Basic V110 for MICA Modems on Cisco Access Servers 1
Basic V110 for MICA Modems on
Cisco Access Servers
Feature Overview
This feature allows V.110 calls to be originated and terminated over ISDN. The V.110
recommendation of the ITU-T rate adapts a low speed connection to an ISDN-B channel allowing
the remote station or terminal adaptor to use the fast call set-up times offered by ISDN. This feature
enables GSM wireless connectivity.
This document describes the Cisco IOS commands and AT commands required to support V.110 on
MICA modems for AS5X00 Access Servers.
This MICA V.110 implementation supports 60 modems per board on the Cisco AS5300 and supports
other connect standards (V.34, V.90, etc.) in addition to V.110. Modems are not dedicated to V.110
only and are allocated dynamically. On the Cisco AS5200, 30 modems per board is supported and
72 modems per board is supported on the Cisco AS5800.
This V.110 implementation for calls on MICA modems are managed by special boardware and
modem code, along with the appropriate Cisco IOS image, in a manner similar to other modulation
standards.
Note
This document is in development. Portions of this document may not be complete or
developed according to the current documentation standards. This document is subject to revision
when the content is available and developed further. Please check the online version periodically
until the document is completed according to the usual documentation standards.
Feature Summary
•
Bearer Rate supported range from 600 bps to 38400 bps.
•
Modem Management is supported.
•
Modem Log for V.110 calls is supported.
•
show modem (Number of connections at specific line speeds is supported.)
•
show modem (Number of calls counters supported)
•
show modem (Display of Tx/Rx line speeds is supported.)
•
show modem version is supported.
•
show modem configuration is supported.
•
show modem operational-status is supported.
•
ATDI command is added to AT command set for V.110 modem dialouts.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Cisco IOS Release 12.0(4)XI1 Note This feature is distinct from the Asynchronous Management Protocol for V.110 Terminal Adaptor Module that runs in the Cisco AS5200 and Cisco AS5300. Benefits V.110 is a digital link access protocol and for Cisco access servers. It operates over an ISDN B channel. ...
Related Features and Technologies Basic V110 for MICA Modems on Cisco Access Servers 3 — 64k bps Related Features and Technologies This feature requires special modem code to be downloaded to the MICA Modems. See the online CCO modem information page. Related Documents See the modem code online docu...
show Command Examples Basic V110 for MICA Modems on Cisco Access Servers 5 http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/dial_r/drprt1/drmodmgt.htm#xtocid10451223 See also show modem at: http://www.cisco.com/univercd/cc/td/doc/product/software/ios113ed/113aa/113aa_2/58cfeats...
