Cisco ONS 15600 - Manual
Cisco ONS 15600 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – NTP-E157 Provision a Multirate PPM
- Page 3 – NTP-E151 Provision an Optical Line Rate
- Page 4 – NTP-E150 Change the Optical Line Rate
- Page 5 – NTP-E149 Delete Pluggable Port Modules
- Page 6 – NTP-E66 Modify Line and Status Thresholds for Optical Ports
- Page 12 – NTP-E105 Change an Optical Port to SDH
- Page 13 – NTP-E125 Change Card Service State
C H A P T E R
11-1
Cisco ONS 15600 Procedure Guide, R5.0
February 2008
11
Change Card Settings
This chapter explains how to change transmission settings on cards in a Cisco ONS 15600.
Before You Begin
As necessary, complete the
“NTP-E57 Document Existing Provisioning” procedure on page 7-2
.
Before performing the following procedures, investigate all alarms and clear any trouble conditions.
Refer to the
Cisco ONS 15600 Troubleshooting Guide
as necessary.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1.
NTP-E157 Provision a Multirate PPM, page 11-2
—Complete this procedure to provision a multirate
pluggable port module (PPM), for the ASAP card. If a multirate PPM was preprovisioned, this
procedure is unnecessary.
2.
NTP-E151 Provision an Optical Line Rate, page 11-3
—Complete this procedure to provision the
optical line rate on a multirate PPM for the ASAP card. Single-rate PPMs do not need to be
provisioned.
3.
NTP-E150 Change the Optical Line Rate, page 11-4
—As needed, complete this procedure to edit
optical line rates for multirate PPMs on the ASAP card.
4.
NTP-E149 Delete Pluggable Port Modules, page 11-5
—As needed, complete this procedure to
delete PPMs for the ASAP card.
5.
NTP-E66 Modify Line and Status Thresholds for Optical Ports, page 11-6
—As needed, complete
this procedure to change line (drop) and threshold settings for all OC-N cards.
6.
NTP-E105 Change an Optical Port to SDH, page 11-12
—As needed, complete this procedure to
change an optical port from SONET to SDH.
7.
NTP-E125 Change Card Service State, page 11-13
—As needed, complete this procedure to change
card service state.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
11-2 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E157 Provision a Multirate PPM NTP-E157 Provision a Multirate PPM Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network. Step 2 Click the Alarms tab: a. Verify...
11-3 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E151 Provision an Optical Line Rate NTP-E151 Provision an Optical Line Rate Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network. Step 2 Click the Alarms tab:...
11-4 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E150 Change the Optical Line Rate Step 9 Click OK . The row on the Pluggable Ports pane turns light blue until the actual SFP is installed and then the row turns white. Stop. You have completed this procedur...
