Cisco ONS 15454 SDH - Manual
Cisco ONS 15454 SDH – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Chapter 5 Ethernet Cards; Ethernet Cards for the ONS 15454 SDH; Card; Card” section on page 5-10; Ethernet Card Software Compatibility
- Page 3 – shows the faceplate and; E100T-G Faceplate and Block Diagram
- Page 4 – Card-Level Indicators
- Page 5 – “5.8 GBICs and SFPs” section on page 5-14
- Page 7 – G1000-4 Faceplate and Block Diagram
- Page 8 – “5.8 GBICs and SFPs” section on; Description
- Page 9 – shows the card faceplate and the block diagram of the card.; G1K-4 Faceplate and Block Diagram
- Page 10 – Caution
- Page 11 – Cisco ONS 15454 SDH Procedure Guide.
- Page 12 – Red SF LED; Blinking amber LED means that traffic is flowing.
- Page 15 – GBIC and SFP Card Compatibility
- Page 16 – GBIC dimensions are:
- Page 17 – Cisco; Supported Wavelengths for CWDM GBICs; CWDM GBIC Wavelengths; Supported Wavelengths for DWDM GBICs; Blue Band; CWDM Mux
- Page 18 – G-Series with CWDM/DWDM GBICs in Cable Network; of latch is a bail clasp (; Mylar Tab SFP
- Page 19 – Bail Clasp SFP
C H A P T E R
5-1
Cisco ONS 15454 SDH Reference Manual, R5.0
April 2008
5
Ethernet Cards
Note
The terms “Unidirectional Path Switched Ring” and “UPSR” may appear in Cisco literature. These terms
do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.
Rather, these terms, as well as “Path Protected Mesh Network” and “PPMN,” refer generally to Cisco’s
path protection feature, which may be used in any topological network configuration. Cisco does not
recommend using its path protection feature in any particular topological network configuration.
The Cisco ONS 15454 SDH integrates Ethernet into a SDH time-division multiplexing (TDM) platform.
This chapter describes the Cisco ONS 15454 SDH E-Series Ethernet cards, G-Series Ethernet cards, and
ML-Series Ethernet cards. It includes descriptions, hardware specifications, and block diagrams for each
card. For G-Series and E-Series Ethernet application information, see
Chapter 14, “Ethernet Operation.”
For installation and card turn-up procedures, refer to the
Cisco ONS 15454 SDH Procedure Guide.
For
ML-Series configuration information, see the
Ethernet Card Software Feature and Configuration Guide.
Chapter topics include:
•
5.1 Ethernet Card Overview, page 5-1
•
•
•
•
•
•
•
5.1 Ethernet Card Overview
The card overview section summarizes card functions, power consumption, and temperature ranges.
Note
Each card is marked with a symbol that corresponds to a slot (or slots) on the ONS 15454 SDH shelf
assembly. The cards are then installed into slots displaying the same symbols. See the
Cisco ONS 15454 SDH Procedures Guide
for a list of slots and symbols.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
5-2 Cisco ONS 15454 SDH Reference Manual, R5.0 April 2008 Chapter 5 Ethernet Cards 5.1.1 Cards Summary 5.1.1 Cards Summary Table 5-1 lists the Cisco ONS 15454 SDH Ethernet cards. 5.1.2 Card Compatibility Table 5-2 lists the CTC software compatibility for each Ethernet card. See Table 2-6 on page 2-4...
5-3 Cisco ONS 15454 SDH Reference Manual, R5.0 April 2008 Chapter 5 Ethernet Cards 5.2 E100T-G Card The ports autoconfigure to operate at either half or full duplex and determine whether to enable or disable flow control. You can also configure Ethernet ports manually. Figure 5-1 shows the faceplate...
5-4 Cisco ONS 15454 SDH Reference Manual, R5.0 April 2008 Chapter 5 Ethernet Cards 5.2.1 E100T-G Slot Compatibility 5.2.1 E100T-G Slot Compatibility You can install the E100T-G card in Slots 1 to 6 and 12 to 17. Multiple E-Series Ethernet cards installed in an ONS 15454 SDH can act independently or ...
