Cisco OL-7822-06 - Manual

Cisco OL-7822-06

Cisco OL-7822-06 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
Page: / 64

Table of Contents:

  • Page 3 – iii; C O N T E N T S; Prepare for Installation; Connect the Power Supply Units
  • Page 4 – iv; Cable the Line Ports; Completing the Installation
  • Page 5 – Installing a Service Control Application; Advanced Configuration of the SCE Platform; Troubleshoot Startup Problems; SCE 1000 Operational Status
  • Page 7 – Information About Preparing for Installation; Site Preparation and Unpacking
  • Page 8 – Tools and Parts; Prepare for Rack-Mount Installation; Workbench or Tabletop Installation
  • Page 11 – The SCE 1000 Mounting Brackets
  • Page 12 – Attach the Brackets to the SCE 1000
  • Page 13 – Assemble the Crossrail Supports
  • Page 14 – Attach the Crossrail Supports to the Rack; Mount the System to the Rack
  • Page 15 – SUMMARY STEPS
  • Page 17 – Connect the Chassis Ground
  • Page 18 – Connecting the Power
  • Page 19 – Connect the DC-Input Power Supply Unit
  • Page 20 – Connect the AC-Input Power Supply Unit
  • Page 21 – Connect the Local Console
  • Page 22 – Perform the Initial System Configuration; Initial System Configuration
  • Page 23 – The Setup Command
  • Page 24 – Parameter
  • Page 26 – Example; Step 1: Configuring Initial Settings
  • Page 27 – Step 2: Configuring the Hostname
  • Page 28 – Step 4: Configuring Time Settings
  • Page 30 – Enter time interval in seconds between unicast updates [1024]:; Step 5: Configuring the DNS Settings
  • Page 31 – DETAILED STEPS; Enter Primary DNS IP address:
  • Page 32 – Step 6: Configuring the RDR Formatter Destination; Information About Access Control Lists
  • Page 33 – permit any; Initial IP address
  • Page 35 – Examples
  • Page 36 – Step 8: Configuring SNMP
  • Page 40 – Step 9: Configuring the Topology-Dependent Parameters; About the Topology-Dependent Parameters
  • Page 42 – Step 10: Completing and Saving the Configuration
  • Page 45 – Connect the Management Interface
  • Page 47 – Information About Cabling; Single Link: Inline Topology
  • Page 48 – Network
  • Page 49 – Cabling the Line Interfaces; Configure GigabitEthernet Auto-Negotiation
  • Page 50 – Connect the GBE Line Interface Ports; SCE Model
  • Page 53 – Examining the LEDs; Verifying Operational Status
  • Page 54 – Viewing the User Log Counters; Viewing Configuration
  • Page 55 – Saving the Configuration Settings
  • Page 57 – Loading and Activating a Service Control Application
  • Page 61 – Identifying Startup Problems; CLI Commands for Troubleshooting; Troubleshooting firmware package installation:; Troubleshooting the management subsystem:
  • Page 62 – Following isa sample output from the show interface Mng command.
Loading the manual

Americas Headquarters

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408

526-4000

800 553-NETS (6387)

Fax: 408

527-0883

Cisco Service Control Engine 1000 2xGBE
Quick Start Guide

Release 3.1
May 2007

Customer Order Number:
Text Part Number: OL-7822-06

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - iii; C O N T E N T S; Prepare for Installation; Connect the Power Supply Units

iii Cisco Service Control Engine 1000 2xGBE Quick Start Guide OL-7822-06 C O N T E N T S C H A P T E R 1 Prepare for Installation 1-1 Information About Preparing for Installation 1-1 Site Preparation and Unpacking 1-1 Tools and Parts 1-2 Prepare for Rack-Mount Installation 1-2 Workbench or Tabletop ...

Page 4 - iv; Cable the Line Ports; Completing the Installation

Contents iv Cisco Service Control Engine 1000 2xGBE Quick Start Guide OL-7822-06 EXAMPLE: 4-8 Step 4: Configuring Time Settings 4-8 EXAMPLE: 4-10 Step 5: Configuring the DNS Settings 4-10 EXAMPLE: 4-11 Step 6: Configuring the RDR Formatter Destination 4-12 EXAMPLE: 4-12 Step 7: Configuring Access Co...

Page 5 - Installing a Service Control Application; Advanced Configuration of the SCE Platform; Troubleshoot Startup Problems; SCE 1000 Operational Status

Contents v Cisco Service Control Engine 1000 2xGBE Quick Start Guide OL-7822-06 EXAMPLE 2: 6-4 C H A P T E R 7 Installing a Service Control Application 7-1 Advanced Configuration of the SCE Platform 7-1 Loading and Activating a Service Control Application 7-1 C H A P T E R 8 Troubleshoot Startup Pro...

Other Cisco Models

All Cisco Other