Cisco OL-3560-02 - Manual
Cisco OL-3560-02 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Synchronous Serial Overview; Note; For a brief description of the clock rate command, see; For
- Page 3 – Synchronous Serial Specifications; LEDs on the PA-4T—Horizontal Orientation Shown; Feet
- Page 4 – PA-4T Port Adapter Receptacles and Cables; LED Label
- Page 5 – For cable pinouts, refer to the
- Page 6 – Serial Port Adapter Cables; shows the connectors at the network end of
- Page 7 – shows the connectors at the network end of the adapter; V.35 Adapter Cable Connectors; Also available, but not shown in
- Page 8 – shows the connectors at the network; X.21 Adapter Cable Connectors; shows the DB-25 connector at the; EIA-530 Adapter Cable Connector; T Port Adapter Cable Pinouts
- Page 11 – Signal
- Page 12 – V.35 Adapter Cable Signals
- Page 13 – Port Adapter Slot Locations on the Supported Platforms; Cisco 7200 Series Router Slot Numbering; X.21 Adapter Cable Signals
- Page 14 – Port Adapter Slots in the Cisco 7206; VIP Slot Numbering; motherboard oriented as shown in; Interface processor slots are numbered as shown in; Port adapter slot 0
- Page 15 – Interface Slot Numbers—Cisco 7505 Shown; Identifying Interface Addresses; Interface ports are numbered from left to right starting with 0.; VIP in interface processor slot 3; Platform; Interface port—0 through 3
- Page 16 – Cisco 7200 Series Routers Interface Addresses; for the interface address format.; VIP Interface Addresses; See; If you remove the VIP with the PA-4T (shown in
C H A P T E R
1-1
PA-4T Synchronous Serial Port Adapter Installation and Configuration
OL-3560-02
1
Overview
This chapter describes the PA-4T port adapter and contains the following sections:
•
Port Adapter Overview, page 1-1
•
Synchronous Serial Overview, page 1-2
•
•
Cables, Connectors, and Pinouts, page 1-4
•
Port Adapter Slot Locations on the Supported Platforms, page 1-13
•
Identifying Interface Addresses, page 1-15
Port Adapter Overview
The PA-4T, shown in
, provides four channel-independent, synchronous serial ports that
support full-duplex operation at T1 (1.544 Mbps) and E1 (2.048 Mbps) speeds. Each port supports any
of the available interface types: Electronics Industries Association/Telecommunications Industries
Association (EIA/TIA)-232, EIA/TIA-449, V.35, X.21, and EIA-530. The cable attached to each PA-4T
interface port determines its type (EIA/TIA-232, and so forth) and its mode (DCE or DTE).
Note
Although the VIP supports online insertion and removal (OIR), individual port adapters do not. To
replace port adapters, you must first remove the VIP from the chassis, and then replace port adapters as
required.
Cisco 7200 series routers support OIR of all port adapter types.
Figure 1-1
PA-4T—Faceplate View
H4496
FAST SERIAL
EN
TD
TC
RD
RC
LB CD
TD
TC
RD
RC
LB CD
TD
TC
RD
RC
LB CD
TD
TC
RD
RC
LB CD
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
1-2 PA-4T Synchronous Serial Port Adapter Installation and Configuration OL-3560-02 Chapter 1 Overview Synchronous Serial Overview Synchronous Serial Overview The PA-4T supports the following interface types: EIA/TIA-232, EIA/TIA-449, V.35, X.21, andEIA-530. EIA/TIA-232, which is by far the most com...
1-3 PA-4T Synchronous Serial Port Adapter Installation and Configuration OL-3560-02 Chapter 1 Overview Synchronous Serial Specifications Synchronous Serial Specifications The PA-4T provides up to four synchronous serial interfaces. Each interface allows a maximumbandwidth of 2.048 Mbps; the speed de...
1-4 PA-4T Synchronous Serial Port Adapter Installation and Configuration OL-3560-02 Chapter 1 Overview Cables, Connectors, and Pinouts The green enabled LED on the port adapter indicates that the motherboard is enabled and receivingpower, and that the port adapter is ready for operation. The followi...
