Cisco OL-12811-01 - Manual
Cisco OL-12811-01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Channelized T1/E1 PRI Network Modules with G.703; Modular Access Router
- Page 5 – Channelized T1/ISDN PRI Network Modules; Connecting CT1/PRI Modules to the Network
- Page 6 – Channelized T1/ISDN PRI with CSU Network Modules
- Page 7 – Connecting CT1/PRI CSU Modules to the Network
- Page 8 – CE1/PRI Module Jumper Settings; Connecting CE1/PRI-B Modules to the Network; CE1/PRI Module Type Default Setting
- Page 11 – Connecting CE1/PRI-U Modules to the Network; PRI Module LEDs; Channelized T1/E1 PRI Network Module with G.703 LEDs; LED
- Page 12 – CT1/PRI Network Module LEDs
- Page 13 – CT1/PRI CSU Network Module LEDs
- Page 14 – CE1/PRI Network Module LEDs
- Page 15 – Upgrading ISDN PRI Network Modules; show diag; Related Documents; Related Topic
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Connecting Cisco ISDN PRI Network Modules to
the Network
Revised: May 1, 2008, OL-12811-01
This guide describes how to connect Cisco Integrated Services Digital Network (ISDN) Primary Rate
Interface (PRI) network modules to your network. It contains the following sections:
•
Channelized T1/E1 PRI Network Modules with G.703, page 2
•
Channelized T1/ISDN PRI Network Modules, page 5
•
Channelized T1/ISDN PRI with CSU Network Modules, page 6
•
Channelized E1/ISDN PRI Balanced (120-Ohm) Network Modules, page 7
•
Channelized E1/ISDN PRI Unbalanced (75-Ohm) Network Modules, page 10
•
•
•
Upgrading ISDN PRI Network Modules, page 15
•
•
Obtaining Documentation, Obtaining Support, and Security Guidelines, page 16
Note
Unless specifically identified, references to PRI modules in this chapter include all these network
modules.
Note
Do not install an ISDN BRI network module in the same chassis as an ISDN PRI network module, unless
you are using Cisco IOS Release 11.3(3)T or later. Earlier Cisco IOS releases do not support this
configuration.
CT1/PRI modules are available with or without a built-in channel service unit (CSU), and with one or
two ports. CT1/PRI modules connect to an external CSU; CT1/PRI-CSU modules connect directly to the
network. Each T1 module provides up to 24 virtual channels per T1 port. Each channel can be configured
individually as a serial interface.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Connecting Cisco ISDN PRI Network Modules to the Network Channelized T1/E1 PRI Network Modules with G.703 2 Connecting Cisco ISDN PRI Network Modules to the Network CT1/PRI and CT1/PRI-CSU modules receive and transmit data bidirectionally, at the T1 rate of 1.544 Mbps. Channelized T1/E1 PRI Network ...
Connecting Cisco ISDN PRI Network Modules to the Network Channelized T1/ISDN PRI Network Modules 5 Connecting Cisco ISDN PRI Network Modules to the Network Figure 4 Connecting a Channelized T1/E1 PRI Network Module with G.703 to a Networking Device Channelized T1/ISDN PRI Network Modules This sectio...
Connecting Cisco ISDN PRI Network Modules to the Network Channelized T1/ISDN PRI with CSU Network Modules 6 Connecting Cisco ISDN PRI Network Modules to the Network Figure 7 Connecting a CT1/PRI Module to a T1 CSU Channelized T1/ISDN PRI with CSU Network Modules This section provides information abo...
