Cisco OC-12/STM-14 - Manual
Cisco OC-12/STM-14 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Configuring the OC-12 Controller
- Page 3 – Parameter
- Page 4 – Configuring the DS3 Serial Interface; “Related Documents” section on page 19; global configuration mode
- Page 5 – Turn off keepalive messages:; Change the shutdown state to up and enable the interface:; Write the new configuration to memory:; explanation of show commands, see the; “Using show Commands to Check System Status” section on; Cisco Remote Connection Management
- Page 7 – Verifying Local and Remote DS3 Port Settings; Figure 2; Setting the Sending and Receiving Rate; Confirmation Message
- Page 8 – Note; Configuring the Clock Source; Using show Commands to Check System Status
- Page 9 – show controllers oc12 slot/port
- Page 12 – Using Loopback Commands; OC-12 Controller Loopback Mode; Loopback modes
- Page 13 – DS3 Channel Loopback Mode; The DS3 channel supports three loopback modes:; Configuring DS3 Port BER Testing
- Page 14 – Checking Bit Errors Using a BERT; BERT Pattern
- Page 15 – Entering Errors in BER Tests; Using show Commands to Verify BERT Configuration; Commands; Shows the fields of a BER test that is still in progress.
- Page 16 – BERT Information; BER test is finished because the interval expired.
- Page 19 – Additional References; Related Documents; Related Topic; Hardware installation; Description
Corporate Headquarters:
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco IOS Software Configuration for the 1-Port
Channelized OC-12/STM-4 (DS3) Line Card
This document describes the software configuration procedure for the 1-port channelized OC-12/STM-4
(DS3) line card on the Cisco 12000 Series Router. This line card is sometimes referred to as the
Channelized OC-12 to DS3 line card or the OC12-DS3 line card.
Feature History for the 1-Port Channelized OC-12/STM-4 (DS3)
Finding Support Information for Platforms and Cisco IOS Software Images
Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image
support. Access Cisco Feature Navigator at
. You must have an account on
Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at
the login dialog box and follow the instructions that appear.
Contents
•
Prerequisites for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card, page 2
•
Information About the 1-Port Channelized OC-12/STM-4 (DS3) Line Card, page 2
•
How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card, page 2
•
Configuration Examples for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card, page 17
•
Additional References, page 19
Release
Modification
11.2(19)GS4
This feature was introduced.
12.0(8)S
This feature was introduced on the 12.0 S train.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Cisco IOS Software Configuration for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card Prerequisites for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 2 Cisco IOS Release 12.0(8)S Prerequisites for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card The Cisco 12000 Series Router must have at le...
Cisco IOS Software Configuration for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 3 Cisco IOS Release 12.0(8)S (Remainder of displayed text omitted from example) Table 1 shows the default OC-12 controller configuration of a 1-...
Cisco IOS Software Configuration for the 1-Port Channelized OC-12/STM-4 (DS3) Line Card How to Configure the 1-Port Channelized OC-12/STM-4 (DS3) Line Card 4 Cisco IOS Release 12.0(8)S Configuring the DS3 Serial Interface After you verify the OC-12 controller configuration, you can configure the ass...
