Cisco NI-1 - Manual
Cisco NI-1 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Supported Equipment
- Page 3 – Summary of Configuration Tasks; Network Timeout
- Page 4 – Initial System Upload
- Page 5 – Before You Upload: Creating a Network Object
- Page 6 – Creating a Node Object
- Page 8 – Network Upload; Uploading the Fabric and Service Elements for a Network Object
- Page 9 – Uploading the Fabric Elements for a Network Object; Uploading the Service Elements for a Network Object; Uploading for Individual Nodes; Uploading the Fabric and Service Elements for a Node Object
- Page 10 – Uploading the Fabric Elements for a Node Object; Uploading the Service Elements for a Node Object; Viewing the Upload Progress
- Page 11 – Working with Logical Ports; Creating Logical Ports; Modifying Logical Ports
- Page 12 – Deleting Logical Ports; Naming Logical Ports; Adding Links Using the GUI
- Page 13 – Working with Service Element Profiles; Creating a Service Element Profile
- Page 14 – Modifying a Service Element Profile; Deleting a Service Element Profile; DSL Physical Port Profile Attributes
- Page 21 – ATM Logical Port Profile Attributes
- Page 25 – ATM-ATM Cross Connection Service Element Profile Attributes
C H A P T E R
6-1
Cisco Provisioning Center User’s Guide
78-11339-01
6
Configuring the Cisco NI-1 DLSAM Equipment
Module
The Cisco 6100/6130 NI-1 DSLAM Equipment Module supports provisioning of cross connections on
Cisco 6100/6130 NI-1 DSL access concentrators. The Cisco 6100/6130 DSL access multiplexer
(DSLAM) is an ATM cell switch that multiplexes traffic from subscriber ports to a single ATM WAN
port. Its 32 slot multiport line-card architecture can support ADSL and SDSL technologies.
Supported Configurations
Two configurations are possible with this system:
•
Subscriber Connection Configurations
•
Subtending Configurations
Subscriber Connection Configurations
Subscriber Connection configurations include the following:
•
Direct Connect Configuration.
This involves connecting one subscriber directly to a modem (ATU-C or STU-C). Traffic is
multiplexed from up to 64 ADSL or 128 SDSL subscriber ports to a single ATM WAN port.
•
Digital Off-Hook Configuration (DOH).
This configuration uses a combination of a Multiplexer Chassis (MC), Line Concentration Chassis
(LCC), and POTS Splitter Chassis (PSC) to provide the highest subscriber concentration. This
configuration uses ADSL technology to support up to 400 ADSL users through 64 ADSL modem
ports, allowing connections to be made when they are needed (i.e., dial up). If a connection is not
established, the central office modem resources are made available to another CPE.
Subtending Configurations
Subtending Configurations include the following:
•
Non-subtended Network Configuration.
Allows individual DSLAMs to be directly linked to the WAN via a trunk that comes from the WAN
port.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
6-2 Cisco Provisioning Center User’s Guide 78-11339-01 Chapter 6 Configuring the Cisco NI-1 DLSAM Equipment Module Supported Equipment • Subtended Network Configuration. Allows up to seven Cisco 6100/6130 chassis to be linked to a single WAN trunk. Subtending is supported in both Direct Connect and ...
6-3 Cisco Provisioning Center User’s Guide 78-11339-01 Chapter 6 Configuring the Cisco NI-1 DLSAM Equipment Module Summary of Configuration Tasks Note In order to configure the NI-1 DLSAM Equipment Module you must have installed it during the CPC Server and Client installation procedures. For more i...
6-4 Cisco Provisioning Center User’s Guide 78-11339-01 Chapter 6 Configuring the Cisco NI-1 DLSAM Equipment Module Initial System Upload Step 4 Run the following commands in succession to source the Server environment and start the CPC Server: cd /opt/SY/Activator/Server/mng/utility . syccpovdef SYn...
