Cisco MAS-7507 - Manual
Cisco MAS-7507 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Product Overview; Figure 1
- Page 6 – Prerequisites
- Page 7 – Safety Guidelines; Warning; Keep tools and chassis components away from walk areas.
- Page 8 – Lifting the Chassis Safely
- Page 9 – Safety with Electricity; Never install telephone wiring during a lightning storm.; Use caution when installing or modifying telephone lines.; Cable Strain Relief
- Page 10 – List of Parts and Tools; Number 2 Phillips screwdriver; Preventing Electrostatic Discharge Damage; Caution
- Page 11 – Following are guidelines for preventing ESD damage:; should be within the range of 1 and 10 megohms.; Preparing the Work Area; Unpacking the Chassis
- Page 13 – Replacing a Rack-Mounted Chassis; Adding a New Chassis to the Rack; with the heaviest component at the bottom of the rack.; network interface cables.
- Page 14 – Replacing the Existing Rack-Mounted Chassis; Turn all power supplies OFF.; Note
- Page 18 – Moving System Components; Moving the Processor Modules
- Page 21 – Proceed to the next section to move the power supplies.; Moving Power Supplies; Follow these steps to move a power supply:
- Page 22 – Repeat Steps 2 through 9 for the second power supply, if any.
- Page 24 – Verifying the Installation; Checking Connections; Check the power supplies for the following:; Restarting the System
- Page 25 – Normal LED is on
- Page 26 – Troubleshooting the Installation; LED Descriptions; Power Supply LEDs
- Page 28 – System Front Panel LEDs; Front Panel LEDs (Cisco 7000 Shown—Identical to Cisco 7507)
- Page 30 – EJECT
- Page 31 – The SP or interface processor has failed.
- Page 32 – If the boot error goes on then goes off as expected, proceed to Step 5.
- Page 34 – Router name
- Page 36 – Translated Safety Warnings; Power Disconnection Warning; siitä virta ja kytke virtajohto irti.; Power Supply Warning
- Page 37 – Power Supply Disconnection Warning; AC units disconnect the power at the circuit breaker on DC units.
- Page 38 – Electric Shock Warning; disconnect the two power supply cords before servicing the unit.
- Page 39 – Chassis Lifting Warning
- Page 40 – DC Power Disconnection Warning
- Page 41 – Lightning Activity Warning; werken of kabels aan te sluiten of te ontkoppelen.
- Page 42 – Chassis Warning—Rack-Mounting and Servicing; Waarschuwing; naar boven te laden met het zwaarste onderdeel onderaan in het rek.; Varoitus; kaikkein raskaimmalla esineellä ja siirry sitten sen yläosaan.; Attention; en plaçant l'élément le plus lourd dans le bas.
- Page 43 – montare nel supporto.; Advarsel; bunnen og opp med den tyngste komponenten nederst i kabinettet.; Aviso; na parte inferior da estante, arrumando-os de baixo para cima.
- Page 45 – DC Power Supply Wiring Warning
- Page 46 – DC Power Connection Warning
- Page 48 – Cisco Information Online; You can access CIO in the following ways:; To obtain general
1
Doc. No.
Copyright © 1995
Cisco Systems, Inc.
All rights reserved.
Cisco 7000 and Cisco 7507
Chassis Replacement Instructions
78-1064-02
Product Numbers: CHAS-7K, MAS-7K, CHAS-7507, MAS-7507
Customer Order Number: DOC-781064=
This document contains instructions for replacing a Cisco 7000 and Cisco 7507 chassis as a spare
part.
Note
With a few exceptions, the chassis replacement procedures are identical for both chassis;
therefore, throughout this document, both chassis are referred to as the chassis; the exceptions are
clearly noted.
You will remove the processor modules and power supplies from your existing chassis and install
them in the replacement chassis. The term processor modules refers to the RP, SP (or SSP), and
interface processors in the Cisco 7000, and the RSP2 and interface processors in the Cisco 7507.
These instructions are applicable only to systems that are already operational and for which first-time
installation and startup verification has been performed. If you have not already installed the system
and verified that it operates properly, or if you are moving the chassis to a new location, refer to the
Cisco 7000 Hardware Installation and Maintenance or Cisco 7507 Hardware Installation and
Maintenance publications for installation information.
The sections in this document include the following:
•
•
•
Unpacking the Chassis, page 11
•
Replacing a Rack-Mounted Chassis, page 11
•
Moving System Components, page 18
•
Verifying the Installation, page 24
•
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Product Overview Product Overview The Cisco 7000 and Cisco 7507 replacement chassis comprise the sheet metal housing, front chassispanels, and all internal components (MAS-7K and MAS-7507, respectively). An optionalreplacement chassis is s...
6 Cisco 7000 and Cisco 7507 Chassis Replacement Instructions Prerequisites Prerequisites Before you move a chassis or any of the system components, review the safety guidelines andrequirements in this section and ensure that you have the necessary parts and tools you will need. Warning This warning ...
Cisco 7000 and Cisco 7507 Chassis Replacement Instructions 7 Prerequisites Safety Guidelines The following guidelines will help to ensure your safety and protect the equipment. This list is notinclusive of all potentially hazardous situations, so be alert. Warning Before working on a system that has...
