Cisco IGX 8400 Series - Manual

Cisco IGX 8400 Series

Cisco IGX 8400 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
Page: / 52

Table of Contents:

  • Page 2 – ACM1. Refer to the Cisco IGX 8400 Series Reference for details.; The locations for the NPMs and SCMs in a Cisco IGX:; — NPM in front slot number 1
  • Page 7 – Inserting the Cards; To insert a Cisco IGX module:; Be sure that you are inserting the module into the correct slot.; Push down on the ejector levers to properly seat the card.
  • Page 8 – Making Signal Connections; — HSSI
  • Page 9 – Connecting Trunks; Bringing Up a UXM-E Trunk; To attach the cables to a back card:
  • Page 11 – dspcds; cnfclksrc; Inverse Multiplexing over ATM on Trunks; All physical ports of an IMA trunk use the same line configuration.
  • Page 12 – Full support for individual physical line alarms and statistics.; Adding an IMA Feeder Trunk; Adding Links to an IMA Feeder Group; dsptrks; cnftrk slot.primary link
  • Page 13 – Removing Links from an IMA Feeder Group; Reduce the number of retained links on the IMA feeder node.; The primary link cannot be removed from an IMA group.; UXM-E Inverse Multiplexing ATM IMA Lines
  • Page 14 – Connecting an NTM T1 or Y1 Trunk; Make the T1 connections as follows:; remaining lines in ascending order.; Connecting an NTM E1 or Subrate Trunk; Make the E1 connections as follows:; Use the cable management feature to help route the cables.
  • Page 15 – Bringing Up a UXM-E in UNI or NNI Port Mode; To attach the cables:
  • Page 16 – To check the status of the lines, use dsplns.; Installing Voice Cards; Connecting a CVM to a T1 or J1 Line; lines in ascending order.
  • Page 17 – Connecting a CVM to an E1 Line or a Subrate Trunk; TDM Transport on the CVM
  • Page 18 – Connecting a UVM to T1 Lines; On port 1 of the primary UVM, connect the cable to the CPE.
  • Page 20 – Connecting a UVM to E1 Lines
  • Page 22 – Connecting a UVM to J1 Lines
  • Page 24 – Making Serial Data Connections
  • Page 25 – Configuring the Port Modes of the HDM Back Cards; At the back of the IGX node, remove the SDI card, as follows:
  • Page 26 – HDM and LDM Redundancy; Configuring the Mode of an LDI Port; Determines whether the port operates in DCE mode or DTE mode
  • Page 28 – Making Frame Relay Connections; Maximum Connections Per Port with Signalling Protocols; The back cards have the following terminations:; Y-Cable Redundancy on the UFMs
  • Page 30 – Connecting UFM Cabling; A UFM-U does not require activation with the upln command.
  • Page 31 – Activate the ports using the upfrport command.; Commands for T1/E1 Frame Relay; Setting Up Frame Relay on an FRM
  • Page 33 – Insert and tighten the mounting screws.; Frame Relay Card Redundancy
  • Page 34 – Setting Up Frame Relay Ports and Connections (FRM)
  • Page 35 – Delete any connections on the port with delcon.; Making Alarm Relay Output Connections; Note that the FAIL LED on the ARM is off. The ACTIVE LED is also off.
  • Page 37 – Table 3-2 shows the unassigned connector pins.; Making External Clock Connections; Connecting a Single Network Management Station
  • Page 39 – LAN Connection for the Network Management Station
  • Page 40 – Configuring the LAN Port; Configure the LAN parameters before connecting the node to a LAN.; The cnflan command has the following parameters:
  • Page 41 – A cnflan screen looks like this:
  • Page 42 – typically applies to network communication.; Manager Operations publication.
  • Page 43 – Connecting a Network Management Station to Multiple Networks
  • Page 44 – Connecting the Printer; Attach the printer to the IGX node as follows:
  • Page 45 – Plug the printer power cord into the appropriate wall receptacle.; Connecting a Modem
  • Page 46 – Connecting the Power Supply Monitor; Initial Startup of the IGX
  • Page 47 – The AC and DC “Okay” LEDs immediately turn on.; NPM Startup Diagnostic Test; The fail screen looks like this:
  • Page 48 – Card Self Test
  • Page 49 – board for checking voltages.; IGX Configuration Summary; The basic tasks to configure an IGX node are as follows:; — Set up optional y-cable redundancy if you require it (addyred)
  • Page 50 – For setting up voice lines:
  • Page 51 – For setting up data connections:; Interworking Connections in a Tiered Network
  • Page 52 – Adding Connections in a Tiered Network through the CLI; where the card in slot is a BNI; Converting a Routing Node to an Interface Shelf
Loading the manual

C H A P T E R

Card Installation and Node Startup 3-1

3

Card Installation and Node Startup

This chapter covers the following topics:

•

How to install the cards in an IGX node that has arrived without cards already installed. (The
rack-mount models of the IGX 8420 and IGX 8430 nodes arrive with cards not installed.)

•

Information unique to each card type that applies to bringing up the node and the network.

•

Connections to LAN, modem, and printer ports.

•

Checklist of readiness before you attempt to bring up the node.

•

The commands and steps for bringing up the node and each type of card set in the node.

•

Power-up diagnostics.

•

IGX configuration summary and IGX management.

Preparing the Cards

The locations of the system cards in the IGX node depend on the hardware configuration. Primary
and redundant NPMs must reside in front slot 1 and 2. The SCM must reside in back slot 1. Except
for these reserved slots, cards can reside in any slot on the appropriate side of the node (but Cisco
recommends that the optional ARM/ARI card set reside in the slot on the far right).

Before you install cards in a rack-mounted IGX 8420 or IGX 8430 node, to indicate whether the
system is an IGX 8420 or an IGX 8430 node, you must either remove or leave a jumper switch on
the SCM. (For the IGX 8410 node and standalone IGX 8420/8430 systems, Cisco sets the switch at
the factory.) The switch is W6. It sits above component U7P (near the top of connector P2). To
indicate an IGX 8430 node, remove the jumper. To indicate an IGX 8420, leave the jumper. Make a
record of this step so you do not have to remove the SCM later to check it. See Figure 3-1.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - ACM1. Refer to the Cisco IGX 8400 Series Reference for details.; The locations for the NPMs and SCMs in a Cisco IGX:; — NPM in front slot number 1

3-2 Cisco IGX 8400 Series Installation and Configuration Preparing the Cards Figure 3-1 W6 Jumper Many card sets support Y-cable redundancy. This feature requires an extra set of cards and a Y-cable.A set of commands exists to specify, delete, and display Y-cable redundancy. For instructions onsetti...

Page 7 - Inserting the Cards; To insert a Cisco IGX module:; Be sure that you are inserting the module into the correct slot.; Push down on the ejector levers to properly seat the card.

Card Installation and Node Startup 3-7 Inserting the Cards Inserting the Cards To insert a Cisco IGX module: Step 1 Attach an ESD-preventive wrist strap to handle the cards. Note The IGX 8410 cabinet has an attached wrist strap both at the front and back. Step 2 Using the 5/32-inch Allen wrench, ope...

Page 8 - Making Signal Connections; — HSSI

3-8 Cisco IGX 8400 Series Installation and Configuration Making Signal Connections Making Signal Connections The remaining sections of this chapter describe how to set up physical lines, ports, trunks, and signalconnections. The Cisco WAN Switching Command Reference and Cisco WAN Switching SuperUser...

Other Cisco Models

All Cisco Other