Cisco Cisco ASR 1006 - Manual

5 Step 4 Insert and tighten the black screws on one side. Figure 2 Front Rack-Mount Brackets for the Cisco ASR 1006 Router Step 5 Repeat Step 1 through Step 4 on the other side of the chassis. Use black screws to secure the rack-mount brackets to the chassis. Step 6 To install the Cisco ASR 1006 Rou...

6 Figure 3 Cisco ASR 1006 Router Rear Rack-Mounting Step 3 Insert and tighten the five screws. After the bracket is secured to the side of the chassis, slide the two remaining components (item 3, Figure 3 ) into the side rack-mount bracket. Step 4 Repeat Step 1 through Step 3 on the other side of th...

8 Step 7 Align the mounting bracket holes with the rack post holes and attach the chassis to the rack. At this point, if there is a third person, then that person can insert the screws while the other two people hold that chassis in place, unless the chassis is resting on a shelf). Step 8 Position t...

9 Figure 5 Installing the Cisco ASR 1006 Router in a Two-Post Rack Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and component damage. Step 1 Position the chassis so the front is closest to you and lift it carefully into the...

10 Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be easily attached to the rack-mount bracket when the chassis is in the rack. This completes the procedure for installing the chassis in a two-post rack. Proceed to the “Attach the Cable-Managem...

12 Chassis Ground Connection Installation Before you connect power or turn on power to your router, you must provide an adequate chassis ground (earth) connection for the router chassis. A ground connector is provided on each Cisco ASR 1006 Router. See Figure 7 . Caution The dual-lug chassis stud mu...

13 Step 8 Connect the opposite end of the grounding wire to the appropriate grounding point at your site to ensure an adequate chassis ground. This completes the procedure for attaching a chassis ground connection. Go to the “Connect the Router to the Network” section on page 13 for information on a...

14 – Connect to the port using the RJ-45-to-RJ-45 cable and RJ-45-to-DB-25 DTE adapter or using the RJ-45-to-DB-9 DTE adapter. Figure 8 Management Ethernet Port Connectors Step 3 Insert an Ethernet RJ-45 cable into the MGMT ETHERNET port. Step 4 Insert the other end of the RJ-45 cable to your manage...

15 Install the Cables in the Cable-Management Bracket No specific card level cable-management will be provided on the SIP carrier cards. SPAs utilize the SPA cable-management brackets that are provided with each SPA as part of their accessory kits. Cables coming off the front side of the SPAs and SI...

16 Step 2 Plug the power cable into the inlet. Note For additional AC power cable strain relief, secure the cable to the power supply handle by inserting a nylon cable tie through the hole in the handle and around the cable. Figure 10 Cisco ASR 1006 Series Router AC Power Supply Step 3 Plug the AC p...

18 Note DC input power cables must be connected to the PDU terminal studs in the proper positive (+) and negative (–) polarity. In some cases, the DC cable leads are labeled, which is a relatively safe indication of the polarity. However, you must verify the polarity by measuring the voltage between...

19 Figure 13 DC Power Supply Ground Studs and Cables Step 4 Ground the other end of the grounding wires to an appropriate grounding point at your site. Step 5 Repeat Steps 2 through Step 4 on the second DC power supply. Wiring the DC-Input Power Source Note The color coding of the DC-input power sup...

23 Figure 17 DC Power Supply Terminal Block and Plastic Cover Caution Secure the wires coming in from the terminal block so that they cannot be disturbed by casual contact. There are tabs located on the base of the DC power supply to which to secure the ties. Step 8 Use tie wraps to secure the wires...

24 Step 2 To ensure that the power supply state is OK, type the show platform command. This output sample is from a Cisco ASR1006 router. The other Cisco ASR1000 routers display similar type of output. MCP_SCAL_R1#sho plat Chassis type: ASR1006 The following output displays: MCP_SCAL_R1# If the LEDs...

30 Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVIPSERVICESK9-M), Experimental Version 12.2(20080110:152728) [BLD-mcp_dev.MCP_CRYPTO_INCREMENTAL_BLD_20080110 103] Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 10-Jan-08 07:29 by mcpre *Feb 13 12:49:01.253: %CRYPTO-6-ISAKMP_ON_O...

35 Note Basic management setup configures enough connectivity for managing the system; extended setup will ask you to configure each interface on the system. For detailed information about setting global parameters, refer to the Cisco ASR 1000_Series Aggregation Services Routers Software Configurati...

36 7 After Installation Follow the instructions in this section to replace field replaceable units (FRUs) after installation. The Cisco ASR 1006 Router supports the following components as FRUs: • Cisco ASR1000-ESP10 and Cisco ASR1000-ESP20 embedded services processors • Shared port adapters • Power...

37 Replace a Power Supply in a Cisco ASR 1006 Router This section provides instructions for removing and replacing the AC power supply and the DC power supply in a Cisco ASR 1006 Router. Before you begin, make certain the chassis is grounded. Remove and Then Replace an AC Power Supply To remove a li...

38 The second is after enabling console logging. Output is at the console (and in the log). 6ru_perf2#conf Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. 6ru_perf2(config)#log con % Ambiguous command: "log con" 6ru_perf2...

40 Console logging: disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 81 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled Persistent logg...