Cisco Cisco 7513 - Manual
Cisco Cisco 7513 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Product Overview; Note
- Page 5 – Installation Safety, ESD Precautions, and Tools Required
- Page 6 – Safety Warnings
- Page 7 – Safety Guidelines; Keep tools and chassis components away from walk areas.
- Page 8 – Never install telephone wiring during a lightning storm.; Warning; measurement should be between 1 and 10 megohms.; Tools Required; ESD-preventive wrist strap
- Page 9 – Removing and Replacing Processor Modules; Removing Processor Modules; To remove processor modules, follow these steps:
- Page 11 – Replacing Processor Modules; To replace processor modules, follow these steps:
- Page 12 – proper flow of cooling air through the chassis.; Figure 7; Removing Power Supplies; To remove a power supply, follow these steps:
- Page 13 – Disconnect the power supply cables from the power supplies.; Figure 8
- Page 14 – Repeat Step 3 and Step 4 for the power supply blank, if one is present.; Removing the Old Card Cage and Backplane Assembly; Timesaver
- Page 15 – To remove the card cage and backplane assembly, follow these steps:; Caution
- Page 16 – Exchanging the EEPROM Devices
- Page 17 – The new EEPROM device(s) that shipped on your new card cage are blank.
- Page 18 – Installing the New Card Cage and Backplane Assembly
- Page 20 – Replacing Power Supplies; To replace the power supply, follow these steps:
- Page 21 – supply, reconnect the power cable at the power source.; Checking the System; Check the following components to make sure they are secure:
- Page 22 – Following is an example of this display:; model and Cisco IOS software release being used.
- Page 23 – Port and Slot Configuration Worksheet; Table 1; Location
- Page 24 – Cisco 7576 Slot Assignments; Router A; — Interface processors are placed in slots 0 through 5; Router B; — Interface processors are placed in slots 8 through 12
- Page 25 – Cisco Connection Online; You can access CCO in the following ways:
1
Cisco Systems, Inc.
All rights reserved.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Cisco Systems, Inc.
Corporate Headquarters
Copyright © 1999
Cisco 7513, Cisco 7513-MX, and
Cisco 7576 Card Cage and Backplane
Assembly Replacement Instructions
Product Numbers: MAS-7513CDCAGE= (Cisco 7513), MAS-7513MX-CDCAGE=
(Cisco 7513-MX), MAS-7576CDCAGE= (Cisco 7576)
This publication provides the procedures to replace the card cage and backplane assembly in the
Cisco 7513, Cisco 7513-MX, and Cisco 7576 routers. The card cage and backplane assembly for the
Cisco 7513, Cisco 7513-MX, and Cisco 7576 chassis can be replaced in the field. The assembly is a
single field-replaceable unit (FRU) that requires replacement by a Cisco-certified service provider
only.
This publication assumes you have already performed troubleshooting on your chassis and system
and determined that this replacement is required.
Document Contents
This publication includes the following sections:
•
•
Installation Safety, ESD Precautions, and Tools Required, page 5
•
Removing and Replacing Processor Modules, page 9
•
Removing Power Supplies, page 12
•
Removing the Old Card Cage and Backplane Assembly, page 14
•
Exchanging the EEPROM Devices, page 16
•
Installing the New Card Cage and Backplane Assembly, page 18
•
Replacing Power Supplies, page 20
•
•
Port and Slot Configuration Worksheet, page 23
•
Cisco Connection Online, page 25
Text Part Number: 78-1895-04
Customer Order Number: DOC-781895=
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Product Overview Caution Before replacing the card cage and backplane assembly, read the “Safety Guidelines” section on page 7. The specific procedures for removing and installing the card cage and ...
Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 5 Installation Safety, ESD Precautions, and Tools Required Figure 4 shows the location of the Cisco 7576 dual arbiters and chassis interfaces on the rear of thebackplane. Figure 4 Location of the Cisc...
6 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Installation Safety, ESD Precautions, and Tools Required Safety Warnings Safety warnings appear throughout this publication in procedures that, if performed incorrectly, mayharm you. A warning symbo...
