Cisco AS5800 - Manual
Cisco AS5800 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CT3 Trunk Card; Each CT3 trunk card performs the following functions:; Note; Each D-channel consumes an HDLC controller.
- Page 3 – Processes counting information for performance monitoring.
- Page 4 – Clocking; CT3 Clocking; LED and Alphanumeric Indicators
- Page 5 – CT3 Trunk Card Front Panel LED and Alphanumeric Indicators; CT3 Trunk Card LED Indicators; LED
- Page 6 – Trunk Card Connectors; CT3 Trunk Card LED Indicators (continued)
- Page 7 – CT3 Trunk Card Front Panel Connectors; Cables; CT3 75-Ohm Coaxial Cable; Using the Test Port
- Page 8 – Trunk Card Bantam Jacks; To drop a particular T1 line to the test port, follow these steps:; Push and hold the push button for two or more seconds.
- Page 9 – Monitor Mode; To monitor a particular T1 line at the test port, follow these steps:; If the display shows
- Page 10 – Specifications; CT3 Trunk Card Specifications; Description
- Page 11 – CT3 Trunk Card BNC Cable Connections; Attach the network end of your CT3 cable to your external network.; Configuring Cable Length; Verifying and Troubleshooting the Installation
- Page 12 – Tips; Configuring the CT3 Trunk Card; Configuration Commands; Table 3-3 lists commands to help you configure your CT3 card.
- Page 13 – T3 Configuration Commands; Command; You are in interface mode when the prompt changes to; Enter an optional text description for the T3 controller.
- Page 14 – Configure clock priority, which is a value from 1 to 50.; Save your changes when ready.
- Page 16 – A typical T1 controller configuration appears as follows:
C H A P T E R
3-1
Cisco AS5800 Universal Access Server Dial Shelf Card Guide
78-7097-03
3
Channelized T3 Trunk Card
The Cisco AS5800 universal access server supports a channelized T3 (CT3) ingress interface that
provides asynchronous aggregation of channelized interfaces and multiplexing on a single T3 facility.
The CT3 trunk card is installed in the Cisco 5814 dial shelf chassis in slots 0 to slot 5. The
Cisco AS5800 currently supports as many as two CT3 trunk cards.
This chapter explains how to remove and replace a CT3 trunk card in the Cisco 5814 dial shelf chassis,
and also includes steps for verifying and troubleshooting your trunk card installation and configuring
your software.
CT3 Trunk Card Overview
The CT3 trunk card contains an onboard M13 multiplexer, which multiplexes 28 separate T1 lines into
a single T3 line. Each CT3 trunk card installed in the Cisco 5814 dial shelf contains all necessary
functionality to terminate link signaling and incoming digital calls.
Figure 3-1 shows the CT3 trunk card.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
3-2 Cisco AS5800 Universal Access Server Dial Shelf Card Guide 78-7097-03 Chapter 3 Channelized T3 Trunk Card CT3 Trunk Card Overview Figure 3-1 CT3 Trunk Card Each CT3 trunk card performs the following functions: • Provides physical termination for as many as 672 sessions. • Provides digital termin...
3-3 Cisco AS5800 Universal Access Server Dial Shelf Card Guide 78-7097-03 Chapter 3 Channelized T3 Trunk Card CT3 Trunk Card Overview • Processes counting information for performance monitoring. • Supports online insertion and removal (OIR), a feature that allows you to remove and replace a trunkcar...
3-4 Cisco AS5800 Universal Access Server Dial Shelf Card Guide 78-7097-03 Chapter 3 Channelized T3 Trunk Card CT3 Trunk Card Overview Clocking All Cisco AS5800 access server trunk cards use the same transmit clock. This clock can originate fromthe following sources: • TDM clock source—A priority val...
