Cisco 78-16409-03 - Manual
Cisco 78-16409-03 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Overview; Note; LED Color
- Page 3 – Installing the 4GE SSM; Connecting the Interface Cables
- Page 4 – Replacing the 4GE SSM; Installing and Removing the SFP Modules
- Page 5 – SFP Module; SFP Module; SX
- Page 6 – Installing the SFP Module; Caution
- Page 7 – Removing the SFP Module; Warning
- Page 8 – Installing and Replacing the ASA SSM 10/20; Assigning Traffic to the SSM
- Page 9 – Installing an ASA SSM 10/20
- Page 10 – Removing and Replacing the Chassis Cover; Removing the Chassis Cover; To
- Page 11 – Remove the screws from the top of the chassis (; Pull the top panel up as shown in
- Page 12 – Replacing the Chassis Cover; Reinstall the network interface cables.
- Page 13 – Working in an ESD Environment; Removing the AC Power Supply; “Rack-Mounting the Chassis” section
- Page 14 – Locate the power connector on the system board.; Chassis bottom; AC power supply
- Page 15 – Back panel
- Page 16 – Replacing the AC Power Supply; “Replacing the Chassis Cover”
- Page 17 – Installing the DC Model
- Page 18 – Install any remaining interface boards as described in
- Page 19 – Replace the DC power supply plastic shied.; Removing and Replacing the CompactFlash; Removing the System CompactFlash; To remove the system CompactFlash, perform the following steps:
- Page 20 – Carefully slide the CompactFlash out of its connector as shown in; System CompactFlash
- Page 21 – Replacing the System CompactFlash; To replace the system CompactFlash, perform the following steps:; Replace the adaptive security appliance cover. See the
- Page 22 – Removing the User CompactFlash; To remove the user CompactFlash, perform the following steps:; Carefully pull the card out of the slot.
- Page 23 – Replacing the User CompactFlash; To replace the user CompactFlash, perform the following steps:
A-1
Cisco ASA 5500 Series Hardware Installation Guide
78-16409-03
A P P E N D I X
A
Maintenance and Upgrade Procedures
This appendix describes how to install and replace the Cisco Security Services Modules (SSM), the
chassis cover, the power supply, and the CompactFlash. This appendix includes the following sections:
•
Installing and Replacing the 4GE SSM, page A-1
•
Installing and Replacing the ASA SSM 10/20, page A-8
•
Removing and Replacing the Chassis Cover, page A-10
•
Working in an ESD Environment, page A-13
•
Removing and Replacing the Power Supply, page A-13
•
Installing the DC Model, page A-17
•
Removing and Replacing the CompactFlash, page A-19
Installing and Replacing the 4GE SSM
The 4GE Security Services Module (SSM) has eight Ethernet ports: four 10/100/1000 Mbps, copper,
RJ-45 ports or four optional 1000 Mbps, small form-factor pluggable (SFP) fiber ports.
This section describes how to install and replace the 4GE SSM in the adaptive security appliance, and
includes the following sections:
•
•
Installing the 4GE SSM, page A-3
•
Replacing the 4GE SSM, page A-4
•
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
A-2 Cisco ASA 5500 Series Hardware Installation Guide 78-16409-03 Appendix A Maintenance and Upgrade Procedures Installing and Replacing the 4GE SSM Overview Figure A-1 lists the 4GE SSM ports and LEDs. Figure A-1 4GE SSM Ports and LEDs Note Figure A-1 shows SFP modules installed in the ports slots....
A-3 Cisco ASA 5500 Series Hardware Installation Guide 78-16409-03 Appendix A Maintenance and Upgrade Procedures Installing and Replacing the 4GE SSM Installing the 4GE SSM To install a new 4GE SSM for the first time, perform the following steps: Step 1 Power off the adaptive security appliance. Step...
A-4 Cisco ASA 5500 Series Hardware Installation Guide 78-16409-03 Appendix A Maintenance and Upgrade Procedures Installing and Replacing the 4GE SSM Replacing the 4GE SSM To replace an existing 4GE SSM, perform the following steps: Step 1 Enter the hw-mod mod 1 shut command in privileged EXEC mode. ...
