Cisco 78-11180-01 - Manual
Cisco 78-11180-01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Before You Begin the Installation; Note
- Page 3 – MTU size; Introduction; Cisco PIX Firewall Configuration Guide, Version 5.2
- Page 4 – PIX 506 Installation Steps; Follow these steps to install a PIX 506:
- Page 5 – or; Configuring the PIX 506; For more configuration information, refer to the
- Page 8 – The PIX 515 can be mounted in a rack, on a wall, or on a flat surface.; Rack Mounting; Use the following steps to install the PIX 515 in a rack:
- Page 9 – Vertical Mounting; PIX 515 Installation Steps; Use the following steps to install a PIX 515:
- Page 11 – Configuring the PIX 515; PIX 515 Feature Licenses
- Page 12 – clear flashfs
- Page 13 – The LEDs display the following transmission states:
- Page 14 – LINK—Shows that data is passing through that interface.; PIX 525 Installation Steps; Use the following steps to install a PIX 525:
- Page 15 – Configuring the PIX 525
- Page 16 – PIX 525 Feature Licenses; Installing a PIX 520 or Earlier Model; PIX 520 or Earlier Model Installation Instructions
- Page 17 – Front
- Page 18 – Figure 2-18 lists the controls on earlier PIX Firewall models.
- Page 19 – PIX Firewall with a Four-Port Interface Card; Slot 0 Contains
- Page 20 – Installing Interface Cables to a PIX 520 or Earlier Model
- Page 21 – Connect one end of the RJ-45 null modem cable to the DB-9 connector.
- Page 22 – Startup Messages; First Messages
- Page 23 – show version; Configuration Guide for the Cisco Secure PIX Firewall Version 5.2; Installing for the First Time or Installing an Activation Key; aaaabbbb; After the Prompts
- Page 24 – The following messages then appear:
- Page 25 – PIX Firewall then displays the following messages:; Enter the; enable; Start configuration mode by entering the; configure terminal
- Page 26 – Writing Different Versions of the Configuration to Flash Memory
- Page 27 – The example startup messages continue:; Writing the Same Version of the Configuration to Flash Memory; If the versions are the same, you are prompted with the following:; Configuration Version Message
- Page 28 – Software Installation Notes; Boothelper Installation; kill
- Page 30 – The following is an example session:; When you are prompted, enter your activation key.; reload; command while the diskette is in the unit.; copy tftp flash; Downloading a Software Image over TFTP
- Page 31 – Using TFTP Commands; Using the copy tftp flash Command; location
- Page 33 – Using the monitor Command; send break; write memory
- Page 35 – The following is an example of the download screen display:
- Page 36 – TFTP Download Error Codes; Description
- Page 37 – Upgrading the Activation Key
C H A P T E R
2-1
Installation Guide for the Cisco Secure PIX Firewall Version 5.2
78-11180-01
2
Installing a PIX Firewall
The following sections in this chapter describe how to install a PIX Firewall:
•
•
Before You Begin the Installation
•
•
•
•
Installing a PIX 520 or Earlier Model
•
•
Installation Overview
Follow these steps to install a PIX Firewall:
Note
If your PIX Firewall model supports a failover configuration, perform the steps that follow
only on the Primary (Active) unit. Refer to Chapter 3, “Installing Failover” for
information about setting up a failover configuration. (Does not apply to the PIX 506.)
Step 1
Review the safety precautions outlined in the
Regulatory Compliance and Safety Information for the
Cisco Secure PIX Firewall Version 5.2
document. You can view this online at the following site:
http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_v52/pixrcs52.htm
Step 2
Completely read the release notes
for your respective software version referenced in the section
“Related Documentation” in “About This Manual.”
Step 3
Unpack the PIX Firewall. The PIX Firewall consists of two main components, the PIX Firewall unit and
a separate accessory kit. The accessory kit contains documentation, a power supply or cord, rack
mounting hardware (not applicable to the PIX 506), and additional software you can use with your
PIX Firewall.
Step 4
Place the PIX Firewall on a stable work surface.
Step 5
If you need to download software, refer to the “Software Installation Notes” section.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2-2 Installation Guide for the Cisco Secure PIX Firewall Version 5.2 78-11180-01 Chapter 2 Installing a PIX Firewall Before You Begin the Installation Before You Begin the Installation Note The information you gather here is required during configuration and is a reminder to find it while installing...
2-3 Installation Guide for the Cisco Secure PIX Firewall Version 5.2 78-11180-01 Chapter 2 Installing a PIX Firewall Installing a PIX 506 • MTU size —The maximum transmission unit (MTU) size for each network interface. You only need to specify a value if you want to set an MTU size that differs from...
2-4 Installation Guide for the Cisco Secure PIX Firewall Version 5.2 78-11180-01 Chapter 2 Installing a PIX Firewall Installing a PIX 506 Figure 2-2 PIX 506 Back Panel PIX 506 Installation Steps The PIX 506 should be placed on a flat, stable surface. The PIX 506 is not rack mountable. Follow these s...
