Chief single stud wall mount accessory - Manual

Page 2 - Installation Instructions; DISCLAIMER

WMA1S Installation Instructions 2 DISCLAIMER Milestone AV Technologies and its affiliated corporations andsubsidiaries (collectively "Milestone"), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all details,condit...

Page 3 - LEGEND

Installation Instructions WMA1S 3 LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fis...

Page 4 - TOOLS REQUIRED FOR INSTALLATION

WMA1S Installation Instructions 4 TOOLS REQUIRED FOR INSTALLATION PARTS #2 5/32" (included) (security) 1/2" (12.7mm) 1/2" (12.7mm) steel stud 7/32" (5.6mm) wood 2" x 4" stud 3/8" (10mm) concrete and concrete block A (1)[WMA1S Assembly] B (1)[Wall bracket] C (4)5/16 x 2-1/...

Page 5 - Site Requirements

Installation Instructions WMA1S 5 Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto asteel stud structure. If the structur...

Page 6 - ASSEMBLY AND INSTALLATION; Installing Mounting Bracket; Concrete or Concrete Block; If installing to a concrete or concrete; Figure 1; Wood Studs; Figure 3

WMA1S Installation Instructions 6 ASSEMBLY AND INSTALLATION The WMA1S single stud wall mount accessory can be mountedto concrete, concrete block, 2" x 4" wood studs or steel studs. Installing Mounting Bracket WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABL...

Page 7 - Figure 4; Steel Studs; See; section before; Figure 5

Installation Instructions WMA1S 7 5. Install three 5/16 x 2-1/2" hex head lag screws (C) throughthree 5/16" washers (D), inner holes of wall bracket (B) andinto drilled holes. (See Figure 4) Figure 4 Steel Studs IMPORTANT ! : See Site Requirements section before proceeding with Steel Studs i...

Page 8 - Figure 8; Installation to Wall Bracket

WMA1S Installation Instructions 8 8. Snap off plastic straps on anchor at wall by pushing side toside, snapping off straps level with flange of plastic cap.(See Figure 8) 9. Repeat Steps 5 through 8 for each mounting hole. Figure 8 10. Place wall bracket (B) over anchors and align mounting holes in ...

Page 9 - Installing Mount Covers; PROJECTOR INSTALLATION; The maximum length column that can

Installation Instructions WMA1S 9 Installing Mount Covers 1. Raise lower cover (X) up to WMA1S. (See Figure 12) Figure 12 2. Lower top cover (W) onto WMA1S. (See Figure 13) 3. Install two #10 x 1" Phillips pan head tapping screws (V)through holes on sides of covers. (See Figure 13) 4. Install tw...

Page 10 - Removing Mount Covers; or

WMA1S Installation Instructions 10 Removing Mount Covers 1. Remove two #8 x 1/2" Phillips pan tapping screws (U) andtwo #10 x 1" Phillips pan tapping screws (V) to free top cover(W) and expose pitch adjustment screw. (See Figure 15) 2. Remove lower cover (X) from WMA1S. (See Figure 15) Figur...

Page 11 - Extension Adjustment

Installation Instructions WMA1S 11 3. Route projector cable(s) under mount cover and throughWMA1S arm. (See Figure 18) Figure 18 4. (Optional) Cables may be tied to inside of WMA1S front cover using cable ties (not included). Route cables nearfront cover and wrap cable tie through slots on front cov...

Page 16 - Europe; Asia Pacific

WMA1S Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Office No. 1 on 12/F, Shatin Ga...

Chief single stud wall mount accessory - Manual

Table of Contents:

Summary

Other Chief Models